fantech QB-X8US3-6G Hard Drive Array Installation Guide

FANTEC QB-X8US3-6G
8×3,5″ SATA HDD USB3.0 eSATA
Quick Installation Guide
Version 1.0

STEP 1 Note

Operation System
Windows Vista / 7 / 8 / 8.1 (32/64bit),
Macintosh OS X 10.5 or later, Linux
Operation Environment
Temperature 0 ~ 50 °C Humidity 90 ⊡ RH
References

1. Smart fan controlled by the built-in thermal sensor and it comes with 2 modes (auto/ manual) and 3 levels of speed:
   Level 1: higher than 55 °C
   Level 2: 45 °C ~ 54 °C
   Level 3: below 45 °C| 2,500rpm ~ 3,500rpm
   1,800rpm ~2,500rpm
   1,200rpm ~1,800rpm
   ---|---

2. eSATA transfer data up to 6.0 Gbps
   USB 3.0 transfer data up to 5.0 Gbps
   USB 1.1 / 2.0 / 3.0 compatible

3. Interface of USB / eSATA can not be used at the same time.3.

4. Under Windows Vista / 7, users can enable GPT when initializing HDD with a total capacity of more than 2TB.

5. Via eSATA port a controller with port multiplier (PM) is required.

STEP 2 Reminders

1. USB port of your PC must support power-off function so that the device would go to sleeping mode. Setting up motherboard’s ( power management ) in S3 is strongly recommended. For more details, please refer to user guide of motherboard BIOS setting.

2. Smart fan controlled by the built-in thermal sensor and it comes with 2 modes (auto / manual) and 3 levels of speed ⊡
   Low
   Medium
   High| below
   between
   hotter than| 45°C
   45°C~55°C
   55°C| 1200rpm
   1800rpm
   2500rpm
   ---|---|---|---

3. Maximum HDD capacity: 6TB each HDD (status: October 2014), 8 single hard drives are displayed at PC (JBOD)

4. • Follow all instructions.
   • Do not place this device near water.
   • Clean only with dry cloth.
   • Do not block any ventilation openings.
   • Only use attachments/accessories.
   • Do not drop or shake the device.
   • Do not move the device when it is powered on.

STEP 3 Front Panel Overview

LED Indication / Button

1. It needs to be pressed and held for 3 seconds to power off.
   Power button
   This design prevents accidental power off.

2. eSATA Link interface use

3. USB Link interface use

4. Blue Power on
   Orange Sleep mode

5. eSATA Link interface option.

6. USB Link interface optionUSB.

7. Smart Fan automatic mode.

8. Smart Fan manual mode.

9. Fan speed level 1.

10. Fan speed level 2.

11. Fan speed level 3.

12. Synchronization comes in 3 modes:
    Blue When the PC is off, the device goes off In 15 seconds.
    Orange When the PC is off, the device goes to sleep mode.
    Off Synchronization is off.

13. Interface button

14. Synchronization mode button
    It needs to be pressed and held for 3 seconds to power off.
    This design prevents accidental power off.

15.  Smart fan button : auto, manual and fan speed from level 1 to level 3
    HDD1 / HDD2 / HDD3 / HDD4 / HDD5 / HDD6 / HDD7 / HDD8
    Blue active
    Purple access

16. Key slot

STEP 4 Rear Panel Overview

Rear Panel

Descriptions

1. Fan
2. eSATA port
3. USB 3.0 / USB 2.0 port
4. AC Input port

HDD Handle

Keys

STEP 5 Quick Installation Guide

1. Please use screws to secure the handles to the HDDs.
2. Unlock the cover with the key supplied and press onto the lock to open the cover.
3. Open the inner covers.
4. Install the HDDs from up to down.
5. Close and secure the covers.
6. Plug in USB or eSATA cable
   USB interface is the default setting and if users wish to change to eSATA, press and hold “Interface” for 3 seconds.

STEP 6 Initialization

MS Windows (32/64 bit)
If the HDD is uninitialized, you may have to initialize it by doing steps as followed: At first click “Start” at your PC and key in “diskmgmt.msc”. After that please press “OK” key.

1. Start disk initialization.
2. Create new partition and format disk.
3. HDD format completed.

Start disk initialization.
Note: Please enable GPT (Vista/7) if the total capacity is more than 2TB and enable MBR if the total capacity is less than 2TB.

Mac OS X 10.5 or later

1. Click on Programs > Utility > Disk Utility icon.
2. HDD initialize…
3. Click Erase
4. Click Erase
5. HDD format in process
6. Format completed

STEP 7 Trouble Shooting

1. If the FANTEC QB-X8US3-6G (2-8 HDDs installed) is connected to the PC with eSATA cable and the PC does not recognize these 4 SATA HDDs, please check if the eSATA controller supportsPort Multiplier or update the eSATA driver version.
2. If the FANTEC QB-X8US3-6G (2-8 HDDs installed) takes too long to initialize, please check if the HDD is securely installed or update the eSATA driver version (for the housing are no drivers necessary!).
3. If the transfer rate seems to be too low, please check if the SATA HDD jumper is set up in 1.5 or 3.0 Gbps.
4. If there is noise with the fan, unscrew the fan, take out the cover, clean the fan and assemble it back.
5. To take the HDD out of the device, slightly press down the handle and pull it out.

Address for warranty return shipments:
FANTEC GmbH
Department RMA/Service
Billwerder Billdeich 605B
21033 Hamburg Germany
Declaration of conformity:
http://www.fantec.de/unternehmen/bestimmungenrichtlinien/ce/

www.fantec.com • www.fantec- forum.com
service@fantec.de

References

• Manual-Hub.com - Free PDF manuals!
• fantec-forum.com
• Homepage
• CE
• The domain name Fantec.eu is for sale!
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>