GE Interlogix 60-639-95R Indoor and Outdoor PIR Motion Sensors Instruction Manual

GE Interlogix 60-639-95R Indoor and Outdoor PIR Motion Sensors

Product Information

Specifications

• Model Nos.: 60-639-95R, 60-639-95R-OD, 60-639-43-EUR, 60-639-43-EUR-OD
• Type: Passive-infrared (PIR) motion sensor
• Indoor Installation Guidelines: Use for large areas or open floor plans
• Outdoor Installation Guidelines: Use to identify motion in a protected outdoor area

Product Usage Instructions

Indoor Installation Guidelines

Follow these guidelines for installing indoor motion sensors:

1. Choose the appropriate mounting option: flush mount, inclined mount, or corner mount.
2. If using the optional swivel mount, attach it to the sensor.
3. Punch out the mounting holes that best fit your application.
4. For corner mounting, use the lower-side holes. For surface mounting with the standard lens, use the lower-back holes.
5. If you have pets, use the upper mounting holes and the optional animal alley lens.
6. If desired, remove the wall-tamper knockout for wall-tamper functionality.
7. Mark the location of the required holes on the mounting surface.
8. Secure the sensor to the mounting surface using wall anchors and screws.

Outdoor Installation Guidelines

Follow these guidelines for installing outdoor motion sensors:

1. Choose a suitable location in the protected outdoor area.
2. Mount the sensor using the appropriate mounting option: flush mount, inclined mount, or corner mount.
3. If using the optional swivel mount, attach it to the sensor.
4. Punch out the mounting holes that best fit your application.
5. For corner mounting, use the lower-side holes. For surface mounting with the standard lens, use the lower-back holes.
6. If you have pets, use the upper mounting holes and the optional animal alley lens.
7. If desired, remove the wall-tamper knockout for wall-tamper functionality.
8. Mark the location of the required holes on the mounting surface.
9. Secure the sensor to the mounting surface using wall anchors and screws.

FAQ

Q: Can outdoor motion sensors be used for intrusion protection?

A: No, outdoor motion sensors should not be used for intrusion protection.

Q: How does the motion sensor detect movement?

A: The motion sensor detects movement by sensing the infrared energy emitted from a body as it moves across the sensor’s field of view.

Q: What are the model numbers of the wireless motion sensor?

A: The model numbers are 60-639-95R, 60-639-95R-OD, 60-639-43-EUR, and 60-639-43-EUR-OD.

Installation Instructions

A passive-infrared (PIR) motion sensor detects movement within a specific area by sensing the infrared energy emitted from a body as it moves across the sensor’s field of view. When this motion is detected, the sensor transmits an alarm signal to the control panel.
Use the indoor motion sensor to protect locations where door/window sensors are impractical or not needed. For example, use a motion sensor to protect large areas or open floor plans. Motion sensors also provide backup protection for door/window sensors.
Use the outdoor motion sensor to identify motion in a protected outdoor area. Detected motion in this protected area can sound chimes or turn on outside lights.

Note

• Do not use outdoor motion sensors for intrusion protection.
• The wireless motion sensor includes the following features:
  • 35 feet by 40 feet coverage area for standard and optional animal alley lenses
  • A masking kit provided to block portions of the coverage area
  • Three-minute transmitter lockout time after an alarm, helping to extend battery life
  • Cover-activated tamper (optional wall-activated tamper is included)
  • Supervisory signals transmitted every 64 minutes to the control panel
  • Sensor low battery reports (trouble) to the control panel
  • Field-selectable sensitivity options

Installation

Indoor Installation Guidelines

Use the following guidelines for installing indoor motion sensors.

•  If possible, locate sensors within 100 feet of the panel. While a transmitter may have a range of 500 feet or more out in the open, the environment at the installation site can have a significant effect on the transmitter range. Sometimes a change in sensor location can help overcome adverse wireless conditions.
• The recommended mounting height is 7 1/2 feet, but the sensor can be mounted from 5 to 8 feet high in the corner of the area you want to protect. See the Animal Alley lens guidelines for mounting the optional Animal Alley lens. Higher mounting provides better range (up to 35 feet), and lower mounting provides better protection close to the motion sensor (see Figures 2 and 3). The optional swivel mount (part #60-737) can be used for difficult mounting locations.
• Position the sensor to protect an area where an intruder would be most likely to walk across the detection pattern (see Figure 1).
• Mount the motion sensor on a rigid surface that is free from vibrations.
• Do not aim the sensor at windows, fireplaces, air conditioners, area heaters, forced air heating vents, or place it in direct sunlight. Sudden changes in temperature may trigger a false alarm from these devices.
• Do not mount the sensor near ductwork or other large metallic surfaces that may affect the RF signals (see RF Testing). The actual acceptable transmitter range should be verified for each installation.
• Mount the sensor permanently on a flat wall or in a corner. Do not set it on a shelf.
• Windows should be closed in any area which has an armed motion sensor.
• A pet will trigger a motion sensor. See animal alley lens guidelines to use a motion sensor when pets are present.
• Mount the motion sensor on an insulated, outside wall facing in.
• Position the sensor so it faces a solid reference point, like a wall.

Outdoor Installation Guidelines

Use the following guidelines for installing outdoor motion sensors.

• The outdoor motion sensor should be used for outdoor applications where there’s a tempera-ture range from 10° to 120° F (12° to 49° C).
• Do not use outdoor motion sensors for intrusion protection since any human, pet, or heated mechanical motion such as an automobile can activate the sensor.
• Follow the indoor motion sensor installation guidelines except for the last four items.
• Do not aim the sensor at objects that may be heated excessively by the sun, such as black top or dark colored objects.
• Do not aim the sensor at foliage or shrubbery which has a dark background.
• The housing is water-resistant but not water-proof. Mount the sensor underneath eaves or porch coverings to prevent over exposure to rain, ice, and direct sunlight.
• The sensor’s coverage area is shown in Figures 2 and 4.

Indoor Motion Sensor

Mounting

The sensor can be flush-mounted, incline-mounted, or corner-mounted depending on the lens used (see Figure 5). Also, the optional swivel mount (#60-737) can be used for difficult mounting locations.

Use the following procedure to mount the sensor.

1. Remove the mounting plate by depressing the button on the top of the sensor body. With the opposite hand pull the mounting plate away from the body of the sensor.

2. Punch out the mounting holes that best fit your application. See Figure 5 for wall mount options. See Figure 6 to determine which knockouts to use when mounting the motion sensor. Use the lower-side holes for corner mounting, or the lower-back holes for surface mounting with the standard lens.

3. For applications with pets, use the upper mounting holes and the optional animal alley lens.

4. If you desire wall-tamper functionality, remove the wall-tamper knockout.=
   Note
   The wall-tamper switch cannot be used when the sensor is swivel or corner mounted.

5. Mark the location of the required holes on the mounting surface.

6. Use wall anchors and screws to secure into place. Attach the sensor to the mounting plate.

7. When testing is completed the PIR can be securely attached to its mounting plate by screwing the smallest enclosed screw into the hole at the top of the mounting plate.

Indoor Motion Sensor Lens Replacement

1. To change the lens, first remove the sensor from its mounting plate by pressing the button on the top of the sensor.
2. Remove the cover by depressing the two tabs on the top and the one tab on the bottom of the sensor body and sliding the cover off (see Figure 8).
3. Remove the installed lens by gently placing pressure on the lens from the outside of the lens.
4. Replace with the appropriate lens by aligning its notches with the appropriate tabs on the cover.
5. Install the new lens with the smooth side facing out and the grooved side facing in.
6. Replace the cover and then replace the sensor with its mounting plate.

Animal Alley Lens Guidelines

The optional animal alley lens (part #60-709) protects installations where pets move about freely. See Figures 2 and 4 for coverage.

• Allowed mounting height is between 3 and 5 feet.
• Be sure to use the flush-mount position or the corner-mount position with the back of the PIR parallel to the walls. Do not use the inclined mount position since this would tilt the PIR’s field of view downward.
• Position the sensor to have a clear line of sight across the protected room.
• For best results, install the sensor higher than the highest point that the pet might reach in the detection area.
• If the detection area contains furniture or other objects upon which the pet could climb or jump, either remove these objects, mount the PIR a safe distance above these objects, or mask these areas.

Setting the Sensitivity

The PIR is set to standard sensitivity at the factory. This sensitivity is preferred for most applications and provides the best immunity to false alarms.

Caution

High sensitivity should only be used in extremely quiet environments where thermal transients are not expected.

1. Locate the sensitivity pins by first removing the mounting plate and the sensor cover as described in steps 1 and 2 of the Lens Replacement process.
2. Locate the sensitivity pins under the battery on the right side of the PIR when looking at the front of the PIR.
3. To change to high sensitivity, move the shorting jumper to the pair of pins that are closer to the top of the PIR (see Figure 7).
4. Walk test the PIR to verify sensitivity.

Outdoor Motion Sensor

Mounting

1. Determine the desired mounting location for the sensor leaving at least four inches of room above the wall mount plate to attach the sensor.
2. Using the screws and anchors supplied, attach the wall mount plate with the opening for the swivel mount facing downward.
3. Attach the sensor assembly to the wall mount plate by screwing the sensor assembly up into the opening in the wall mount plate.
4. To remove the sensor for testing or battery replacement, slide the front cover of the sensor upward until the sensor can be removed.

Filter Installation

A one-inch by one-inch piece of lens material has been included with the outdoor motion sensor. The filter reduces the sensor sensitivity to white light sources (sunlight and headlights) and infrared sources. Install the filter when experiencing unwanted sensor activations due to these sources.

1. Remove the sensor from its water-resistant enclosure by sliding the front cover upward until the sensor can be removed.
2. Remove the mounting plate of the sensor by pressing the button on top of the sensor.
3. Remove the front cover of the sensor by depressing the two tabs on the top and the one tab on the bottom of the sensor body and sliding the cover off (see Figure 8)
4. Place the sensor on its back and drop the filter into the lens chamber covering the sensor’s detector.
5. Replace the cover, making sure the filter remains in the lens chamber and does not interfere with the attachment of the cover.
6. Replace the sensor’s mounting plate and install the sensor in its water-resistant enclosure.

Testing

Walk Testing

Walk testing should be done to determine the sensor’s actual coverage area. The edge of the coverage pattern is determined by the first flash of the LED. This may change slightly depending on the sensitivity setting. Walk test the unit from both directions to determine the pattern boundaries.

1. Remove the sensor body from the mounted mounting plate, activate the tamper switch, and remount the body to activate the 60-second walk test mode.
2. Walk across the coverage pattern to determine the coverage area, indicated by LED activation. Each activation extends the walk test mode for an additional 60 seconds.

After 60 seconds without motion, the walk test mode and the LED will no longer activate when motion is detected.

Note

When the walk test mode has ended, an alarm can be transmitted only after 3 minutes have passed since the previous alarm. This 3-minute lockout time reduces unnecessary RF transmissions in high-traffic areas thereby extending battery life.

Caution

Environment Testing

Indoor Motion Sensors

Turn on all heating or air conditioning sources that would normally be active during the protec-tion period. Stand away from the sensor and outside the coverage pattern and watch for alarms.

Outdoor Motion Sensors

Verify that the sensor’s coverage area does not extend into undesired areas that might cause unwanted activations. These areas may include undesired human, pet, or automobile motion.

Coverage Masking

After walk testing and environment testing are completed, masking labels can be applied to the sensor’s lens to block the detection of problem areas. The masking labels provided are cut to match the corresponding lens segments.

1. Determine which detection zone/lens segment needs a masking label.
2. Peel the desired mask label from its backing and apply to the inside of the lens segment to be blocked.

Programming

Refer to the panel installation instructions for information on programming the sensor into the panel.

Final Testing

Final testing should be done to verify radio signal integrity and confirm control panel programming and response. The actual transmitter range can be determined by performing a sensor test as follows:

1. After the sensor has been mounted, remove it from its mounting plate and activate the tamper switch to start the walk test mode.
2. Replace the sensor in its mounting plate.
3. Place the control panel in test mode. Move across the detection pattern until the sensor’s LED turns on. STOP your motion.
4. Listen for the appropriate system response. If the system does not respond, proceed to the “Troubleshooting” section.

Maintenance

At least once a year, the range and coverage should be verified for proper operation. The end user should be instructed to put the sensor in walk test mode and walk through the far end of the coverage pattern to verify proper detection.

Replacing Batteries

When battery replacement is necessary, observe proper polarity (as shown in the battery compartment) when installing the new battery. The sensor may be damaged if installed incorrectly. As you look at the battery compartment, on the left side the positive battery end is down and on the right side the positive end is up. When the battery is replaced, wait at least 3 minutes after installing the battery before activating the walk test mode. See Figure 8 for battery locations.

Caution

Replace only with two AA 1.5V Alkaline batteries. Dispose of used batteries according to manufacturer’s instructions and local government authorities .

Troubleshooting

Follow these guidelines if the system does not respond correctly when the sensor is activated.

• Check to program and re-program the sensor into the panel if necessary.
• Move the sensor to another location and test for the correct response.

To relocate a sensor:

1. Test the sensor a few inches from the original position.
2. Increase the distance from the original position and retest until an acceptable location is found.
3. Mount the sensor in the new location.
4. If no location is acceptable, test the sensor as described below:
   • Test a known good sensor at the same location.
   • If the system does not respond, avoid mounting a sensor at that location.
   • If the replacement sensor functions, return the problem sensor for repair or replacement.

Specifications

• Compatibility: ……………………..Concord™, Concord Express, International Concord, Simon®, Euro Simon,
  • Quik Bridge®, 1 & 2 Channel Receiver, Quik Bridge Euro Repeater SAW,
  • Quik Bridge International Loop Receiver, SuperBus®, 2000 RF Receiver,
  • SuperBus 2000 433 MHz Receiver
• Power source: ………………………2 AA 1.5V alkaline batteries
• Typical battery life: ……………..2-4 years at 68° F (20° C) not verified by UL
• Transmitter Frequency: ……….319.5 MHz
• Operating temperature: ……….32° to 120° F (0° to 49° C) Indoor Motion Sensor
  • 10° to 120° F (12° to 49° C) Outdoor Motion
• Storage temperature range: ….-30° to 140° F (-34° to 60° C)
• Maximum Humidity…………….90% Relative Humidity non-condensing
• Dimensions: …………………………2.9 in. (7.3cm) x 2.4 in. (6 cm) x 1.9 in. (4.8 cm) (L x W x H)

Declaration of Conformity

• Manufacturer’s Name: …………GE Interlogix
• Manufacturer’s Address: ……..2266 North 2nd Street
  • North St. Paul, MN, USA 55109
• EU Representative:………………Interlogix Europe & Africa
  • Excelsiorlaan 28
  • B-1930 Zaventum
  • Belgium
• Product Identification: …………Product: Indoor and Outdoor PIR Motion Sensors
  • Model Numbers: 60-639-43-EUR and 60-639-43-EUR-OD
  • Brand: GE Interlogix

Means of Conformity

We declare under our sole responsibility that this product is in conformity with Directive 93/68/EEC (CE Marking) and complies to the essential requirements of 1999/5/EC (R&TTE) based on test results using (non)-harmonized standards in accordance with the Directives mentioned.

Concerning| R &TTE|
---|---|---
A sample of the product has been tested by:| Mikes Product Service| KTL Arnhem
Standards used:| I-ETS 300 220

(10.1993)

| EN50130-4 (1995)

EN50130-4/A1 (1998)

EN60950, 1992 (A1, A2, A3, A4, A11) IEC950, 2nd ed. (A1, A2, A3, A4)

Test report:| T14152-1-02SM| 98639220

98639250

Notices

Approved for use in the countries marked with a check (√).

© 2002 GE Interlogix Quik Bridge, Simon, and SuperBus are registered trademarks of GE Interlogix. Concord is a trademark of GE Interlogix All other trademarks are All rights reserved 2266 Second Street North

• North Saint Paul. MN 55109
• Technical Support: 800-777-2624

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>