KING CANADA PALM DETAIL SANDER Instruction Manual
- June 17, 2024
- KING CANADA
Table of Contents
KING CANADA PALM DETAIL SANDER
Specifications
- Model: 8303
- Manufacturer: King Canada Tools
- Warranty: 2-Year Limited Warranty for Non-Commercial Use
General Safety Instructions for Power Tools
-
Know Your Tool: Read and understand the owner’s manual and labels affixed to the tool. Learn its application, limitations, and potential hazards.
-
Keep Work Area Clean: Cluttered areas and benches invite accidents. Ensure the floor is clean and not slippery due to wax and sawdust build-up.
-
Avoid Dangerous Environment: Do not use power tools in damp or wet locations or expose them to rain. Keep the work area well lit and provide adequate surrounding workspace. Keep Children Away: All visitors should be
kept a safe distance from the work area. -
Make Workshop Child-Proof: Use padlocks, master switches, or remove starter keys to prevent unauthorized use.
-
Use Proper Speed: Operate the tool at the recommended speed for better performance and safety.
-
Use the Right Tool: Do not force the tool or attachment to perform tasks for which they were not designed.
-
Wear Proper Apparel: Avoid wearing loose clothing, gloves, neckties, or jewelry that may get caught in moving parts. Non-slip footwear is recommended, along with protective hair covering and rolled-up long sleeves. Safety glasses should always be worn.
Electrical Information & Assembly
Voltage Warning: The performance of the tool may vary depending on local line voltage. Extension cord usage can also affect tool performance.
Extension Cords
Your tool has a polarized, two-prong plug. Do not alter the plug in any
way. Only use rounded jacket extension cords listed by Underwriters
Laboratories (UL). Improper use of extension cords can result in inefficient
operation and overheating. Ensure your extension cord is rated to allow
sufficient current flow to the motor. If using the tool outdoors, use an
extension cord rated for outdoor use (signified by WA on the jacket). The
minimum wire size of the extension cord depends on the amperage of the tool
and the length of the extension cord. Refer to the chart below to determine
the required American Wire Gauge (AWG)rating for your situation:
| Length of Conductor | 0-25 feet | 26-50 feet | 51-100 feet |
|---|---|---|---|
| Wire Size Required (AWG) | Refer to chart | Refer to chart | Refer to chart |
Product Usage Instructions
Preparation
- Ensure you have read and understood all safety instructions mentioned above.
- Clean your work area and remove any clutter or obstacles.
- Gather all necessary materials and accessories.
- Inspect the palm detail sander for any visible damage or defects.
Power Connection
- Ensure the palm detail sander is unplugged before proceeding.
- Locate a suitable power outlet near your work area.
- Check the voltage requirements of the palm detail sander and ensure the outlet matches.
- Plug the sander into the power outlet securely.
Sanding Operation
- Select the appropriate sanding attachment for your desired task.
- Attach the sanding pad securely to the sander.
- Hold the palm detail sander firmly with both hands, ensuring a comfortable grip.
- Turn on the sander using the power switch.
- Move the sander gently across the surface, applying light pressure as needed.
- Avoid excessive pressure or prolonged sanding in one area to prevent damage.
- Continue sanding until you achieve the desired result.
Cleaning and Maintenance
- Turn off and unplug the palm detail sander.
- Remove the sanding pad and clean it using a brush or compressed air to remove dust and debris.
- Wipe down the sander with a clean, dry cloth to remove any remaining dust.
- Store the palm detail sander in a dry and secure location.
FAQ
Q: What is the warranty period for the palm detail sander?
A: The palm detail sander comes with a 2-year limited warranty for non-
commercial use. Please retain your proof of purchase for warranty and
servicing purposes.
Q: Can I use the palm detail sander in wet conditions?
A: No, it is not recommended to use power tools, including the palm detail
sander, in damp or wet locations or expose them to rain. Ensure a dry and
well-lit work area.
Q: How do I determine the appropriate extension cord for the palm detail
sander?
A: Refer to the chart provided in the manual to determine the minimum
American Wire Gauge (AWG) rating required based on the length of the extension
cord. Make sure to use extension cords listed by Underwriters Laboratories
(UL) and suitable for the tool’s power requirements.
GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS
-
KNOW YOUR TOOL
Read and understand the owners manual and labels affixed to the tool. Learn its application and limitations as well as its specific potential hazards. -
KEEP THE WORK AREA CLEAN.
Cluttered areas and benches invite accidents. Make sure the floor is clean and not slippery due to wax and sawdust build-up. -
AVOID DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations or expose them to rain. Keep work area well lit and provide adequate surrounding work space. -
KEEP CHILDREN AWAY.
All visitors should be kept a safe distance from work area. -
MAKE WORKSHOP CHILD-PROOF.
Use padlocks, master switches or remove starter keys. -
USE PROPER SPEED.
A tool will do a better and safer job when operated at the proper speed. -
USE RIGHT TOOL.
Don’t force the tool or the attachment to do a job for which it was not designed. -
WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings, watch) because they could get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair. Roll up long sleeves above the elbows. -
ALWAYS WEAR SAFETY GLASSES.
Always wear safety glasses (ANSI Z87.1). Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. Also use a face or dust mask if cutting operation is dusty. -
MAINTAIN TOOL WITH CARE.
Keep tools clean for best and safest performance. Follow instructions if any for lubricating and changing accessories. -
DISCONNECT TOOLS.
Before servicing, when changing accessories or attachments. -
AVOID ACCIDENTAL STARTING.
Make sure the switch is in the ‘’OFF’’ position before plugging in. -
CHECK DAMAGED PARTS.
Before further use of the tool, a guard or other parts that are damaged should be carefully checked to ensure that they will operate properly and perform their intended function. Check for alignment of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. Aguard or other parts that are damaged should be properly repaired or replaced. -
NEVER LEAVE MACHINE RUNNING UNATTENDED.
Turn power ‘’OFF’’. Don’t leave any tool running until it comes to a complete stop.
ELECTRICAL INFORMATION & ASSEMBLY
Warning
The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into thisN product, but must be supplied by the operator.
Note : The performance of this tool (if powered by line voltage) may vary
depending on variations in local line voltage. Extension cord usage may also
affect tool performance
VOLTAGE WARNING
Before connecting the tool to a power source (receptacle, outlet, ect.) be
sure the voltage supplied is about the same as that specified on the nameplate
of the tool. If one says 120V and the other says 115V then there will be no
complications. Never try to plug a 115V tool into a 230V outlet, or the other
way around. The plug and outlet have completely different shapes. This is
because a power source with a voltage greater than that specified on the tool
can result in SERIOUS INJURY to the user, as well as damage to the tool. If in
doubt, DO NOT PLUG IN THE TOOL.
EXTENSION CORDS
Your tool has a polarized, two-prong plug. Do not alter the plug in any
way. Only use rounded jacket extension cords listed by the Underwriters
Laboratories (UL). Improper use of extension cords may cause inefficient
operation of your tool which can result in overheating. Be sure your extension
cord is rated to allow sufficient current flow to the motor. If you are using
the tool outdoors, use an extension cord rated for outdoor use (signified by
“WA” on the jacket). The extension cord must have a minimum wire size
depending on the amperage of the tool and the length of the extension cord.
This size is determined by its AWG (American Wire Gauge) rating. The smaller
the gauge, the greater the cable’s capacity. The amount of cords used does not
matter: Total length determines the minimum AWG rating. Every cord must meet
the AWG rating. Use the chart below to determine what AWG rating is required
for your situation. Cord length is rated in feet.
ASSEMBLY
Your Detail Palm Sander comes fully assembled. For installation of sandpaper
and operating instructions, please refer to the operation section of this
manual.
OPERATION
OPERATION
Turning the Palm Sander On and Off
- Make certain that the object to be sanded is secure. Make sure that the sander is not in contact with the table or work materials. Starting the sander before placing it onto the work surface will reduce deep scratching in the surface to be sanded.
- Before you plug in the cord make certain the switch is in the OFF position. To turn the switch ON, press the switch up to the “I” position. See figure below.
- To turn the switch OFF, press it down to the “0” position. See Figure below.
INSTALLING AND REPLACING THE VELCRO SANDING PAPER
- Before installing sanding paper, make certain that the base is free of dust and dirt. Make certain that the tool is UNPLUGGED and that the switch is in the OFF position.
- The palm sander’s sanding paper have a velcro backing that affixes on the base easily and without clamps. To connect the sanding paper to the base, line up both and press together. Press the sanding paper firmly into place.
- To remove the velcro sanding paper, carefully peel the velcro sanding paper from the palm sander base.
Turning the Palm Sander On and Off
Installing and Replacing the Velcro Sanding Paper
SANDING
-
Choose the proper grit sanding paper. If preparing wood for painting, or if removing paint, use a coarse grit sanding paper. Use a fine grit for finish work.
-
Secure the item to be sanded. Make certain that the sanding paper is firmly in place.
-
With the sander not in contact with the workpiece, press the switch to the “ON” position.
-
Carefully move the Palm Sander to the workpiece and begin sanding.
Warning : Do not sand any area too heavily or for more than a few seconds at a time. Apply even pressure in a random pattern over the entire surface. -
To sand down profiles and grooves, use the point or edge of the plastic base.
-
Every few minutes, check the condition and wear of the sanding paper. Replace if necessary.
Warning : Do not use torn or severely worn sanding paper. You may damage your work surface or suffer physical injury. -
When you are done sanding the desired area, remove the sander from the work surface before turning OFF the sander!
Dust Extraction
Regularly clean the Palm Sander of excess dust and debris.
Note : A dust vacuum system hose (not included) can be attached to the 1-1/4” dust extraction chute for a more efficient method of sawdust collection.
PARTS DIAGRAM & PARTS LISTS
Refer to the Parts section of the King Canada website for the most updated
parts diagram and parts list.
IMPORTANT INFORMATION
PROOF OF PURCHASE
Please keep your dated proof of purchase for warranty and servicing purposes.
LIMITED TOOL WARRANTY
KING CANADA makes every effort to ensure that this product meets high quality
and durability standards. KING CANADAwarrants to the original retail consumer
a 2-year limited warranty as of the date the product was purchased at retail
and that each product is free from defects in materials. Warranty does not
apply to defects due directly or indirectly to misuse, abuse, negligence or
accidents, repairs or alterations and lack of maintenance. KING CANADA shall
in no event be liable for death, injuries to persons or property or for
incidental, special or consequential damages arising from the use of our
products. To take advantage of this warranty, Bthe product or part must be
returned for examination by the retailer. Shipping and handling charges may
apply. If a defect is found, KING CANADA will either repair or replace the
product.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>