KING CANADA KCG-130 13 HP Gasoline Engines Instruction Manual

GASOLINE ENGINES
Instruction Manual MODEL: KCG-65
(6.5 HP)
MODEL: KCG-130
(13 HP)

KCG-130 13 HP Gasoline Engines

Read this manual. Do not attempt to operate engine until you have read and understood the safety, operation, and maintenance instructions in this manual.
INSTRUCTION MANUAL
COPYRIGHT © 2011 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
1-YEAR LIMITED WARRANTY
FOR 6.5 HP OR 13 HP ENGINE
KING CANADA TOOLS
OFFERS A 1-YEAR LIMITED WARRANTY FOR NON-COMMERCIAL USE.

IF YOU ARE EXPERIENCING PROBLEMS, DO NOT RETURN TO THE RETAILER, CALL THIS TOLL-FREE NUMBER FOR SERVICE INFORMATION
1-877-636-4214

BEFORE CALLING THE ABOVE TOLL-FREE NUMBER, PLEASE READ THIS MANUAL, SPECIFICALLY THE SAFETY PRECAUTIONS, THE INSPECTION BEFORE OPERATION AND THE TROUBLESHOOTING GUIDE.

• DO NOT RETURN THE DEFECTIVE PRODUCT TO THE RETAILER.

WARRANTY INFORMATION
PROOF OF PURCHASE
Please keep your dated proof of purchase for warranty and servicing purposes.
REPLACEMENT PARTS
Replacement parts for these engines are available at our authorized KING CANADA generator service centers across canada. For servicing, call the above toll free number to get servicing instructions and be sure to have your proof of purchase if you are claiming warranty work.
LIMITED TOOL WARRANTY
KING CANADA makes every effort to ensure that this product meets high quality and durability standards. KING CANADA warrants to the original retail consumer a 1-year limited warranty as of the date the product was purchased at retail and that each product is free from defects in materials.
THIS WARRANTY IS NOT TRANSFERABLE AND DOES NOT COVER

• Damage or liability caused by shipping, improper handling, improper installation, improper maintenance, improper modification, or the use of accessories and/or attachments not specifically recommended.
• Repairs necessary because of operator abuse or negligence, or the failure to install, operate, maintain, and store the product according to the instructions in the owner’s manual.
• Damage caused by cold, heat, rain, excessive humidity, corrosive environments and materials, or other contaminants.
• Expendable items that become worn during normal use such as fuel filters, air cleaners, spark plugs, and engine oil.
• Cosmetic defects that do not interfere with product functionality.
• Freight costs from customer to an authorized warranty service location.
• Repair and transportation costs of products or parts determined not to be defective.
• ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCT.
• RETAIN THE ORIGINAL CASH REGISTER SALES RECEIPT AS PROOF OF PURCHASE FOR WARRANTY WORK.

KING CANADA shall in no event be liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products. Shipping and handling charges may apply. If a defect is found, KING CANADA will either repair or replace the product.
KING CANADA TOOLS INC. DORVAL, QUEBEC, CANADA H9P 2Y4

BASIC & SPECIFIC SAFETY PRECAUTIONS

BASIC SAFETY INFORMATION
EXHAUST FUMES ARE DANGEROUS

• Never operate the engine in a closed area or it may cause unconsciensness and death within a short time. Operate in a well ventilated area.
  FUEL IS HIGHLY FLAMMABLE AND POISONOUS

• Always turn off the engine when refueling.

• Never refuel while smoking or in the vicinity of an open flame.

• When operating or transporting engine, be sure to keep it upright. If it tilts, fuel may leak from the carburetor or fuel tank.
  ENGINE AND MUFFLER MAY BE HOT

• Place the engine in an appropriate location, away from children and pedestrians.

• Avoid placing any flammable materials near the exhaust outlet during operation.

• Keep a 4ft. clearance from buildings or other equipment around the engine to prevent overheating.
  WARNING! The engine muffler will be very hot after use, avoid touching the engine or muffler while they are still hot.
  ELECTRIC SHOCK PREVENTION

• Never operate in rain or snow.

• Never touch the engine with wet hands or electric shock could occur.

FUEL
Make sure there is sufficient fuel in the tank.
SPECIFIC SAFETY INFORMATION TAMPERING WITH FACTORY SET ENGINE SPEED SETTINGS.
Engine speed has been factory set to provide safe operation.
Tampering with the engine speed adjustment could result in overheating and could cause a fire.
Never attempt to “speed-up” the engine to obtain more performance.
ATTEMPTING TO FILL THE FUEL TANK WHILE THE ENGINE IS RUNNING.
Gasoline and gasoline vapors can become ignited by coming in contact with hot components such as the muffler, engine exhaust gases, or from an electrical spark.
Turn engine off and allow it to cool before adding fuel to the tank.
Equip area of operation with a fire extinguisher certified to handle gasoline or fuel fires.
SPARKS, FIRE, HOT OBJECTS
Cigarettes, sparks, fires, or other hot objects can cause gasoline or gasoline vapors to ignite.
Add fuel to tank in well ventilated area. Make sure there are no sources of ignition near the engine.

INADEQUATE VENTILATION
Materials placed against or near the engine or operating in areas where the temperature exceeds 40° C ambient (such as storage rooms or garages) can interfere with its proper ventilation features causing overheating and possible ignition of the materials or buildings.
Operate engine in a clean, dry, well ventilated area a minimum of four feet from any building, object or wall. DO NOT OPERATE UNIT INDOORS OR IN ANY CONFINED AREA.
RISK OF BREATHING – INHALATION HAZARD
Operate engine in clean, dry, well ventilated area. Never operate unit in enclosed areas such as garages, basements, storage, sheds, or in any location occupied by humans or animals.
Keep children, pets and others away from area of operating unit.
Breathing exhaust fumes will cause serious injury or death. Gasoline engines produce toxic carbon monoxide exhaust fumes. WHEN REFUELING
STOP ENGINE!
NO SMOKING!
DO NOT SPILL GASOLINE!
KEEP FLAMMABLE MATERIALS AWAY.
RISK OF FIRE.
GASOLINE ENGINES PRODUCE TOXIC CARBON MONOXIDE EXHAUST FUMES.

GETTING TO KNOW YOUR ENGINE

The following information applies to both engines.

1. Fuel cap. Make sure the fuel cap is always screwed on tightly.
2. Fuel tank. Unleaded gasoline only!
3. Low oil sensor. This engine detects and shuts off automatically when the oil level is too low. In case of an auto shut-off, check oil level with dipstick and fill to recommended level with SAE 10W30 engine oil.
4. Oil gauge dipstick. Check the oil level using this oil gauge dipstick.
5. Oil drain bolt.
6. Power ON/OFF switch. This switch must be switched to “ON” before pulling recoil starter.
7. Recoil starter. Starts the engine.
8. Fuel Shut-off Valve. Regulates the flow of fuel to the engine. The fuel shut-off valve must be fully opened before starting the engine.
9. Choke lever. Once the engine is started, it is necessary to gradually move the choke lever to the “OPEN” position, see instructions futher in this manual. On warm starts, choke is not needed.
10. Carburetor throttle lever. Once the engine is started, move the trottle lever to increase or decrease engine speed.
11. Air cleaner element/cover. Periodically the air cleaner filter must be checked and maintained, see maintenance section.
12. Muffler. Be careful, the muffler can get very hot during operation, keep hands away.
13. Spark plug/cover. The spark plug must be check periodically for carbon deposits and/or discoloration, see maintenance section.

PRE-START CHECK

WARNING! To prevent permanent damage to your engine, you MUST check oil level, fuel level and air cleaner filter before starting.
MOUNTING
Before operating your engine, mount it on a flat, level surface which can withstand the weight and vibrations of the engine. To do this, bolt the engine using the 4 mounting holes in the base (hardware not included). If mounted to a permanent indoor location, to prevent carbone monoxide poisoning, a proper exhaust ventilation system MUST be installed.
PRE-START CHECK
OIL LEVEL
WARNING! This engine has been shipped from the factory without oil or very little oil in the crankcase. Operating your engine without the correct amount of oil can damage it.
Oil crankcase capacity: 0.6 litres (KCG-65), 1.1 litres (KCG-130).
Always check the oil level before starting the engine, make sure the engine is on a level surface. To check oil level;

1. Turn the oil gauge dipstick (A) Fig.1 counterclock- wise, remove it and clean it with a clean cloth.
2. Fully reinsert the oil gauge dipstick and pull it out to check the oil level.
3. If the oil level is halfway up the dipstick or below, refill with SAE 10W30 oil through the dipstick hole until the oil level reaches 3/4 up the dipstick or until it reaches the bottom lip of the dipstick hole as shown in illustration.
4. Reposition the oil gauge dipstick and tighten it by turning clockwise.

FUEL LEVEL
WARNING! Make sure there is enough fuel in the fuel tank before operating.

1. If it is necessary to add fuel, first make sure the engine switch is OFF, then open the fuel cap (A) Fig.2 by turning it counterclockwise.
2. Make sure the fuel filter cup (B) is positioned inside the tank opening before refueling.
3. The fuel filter cup (B) comes with a max. fuel level (C), do not fill the fuel tank past the max. fuel level. When refueling, keep in mind all safety precautions and make sure to add enough fuel based on usage. Use clean unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Fuel tank capacity: 3,6 litres (KCG-65), 6,5 litres (KCG-130).

AIR CLEANER FILTERS
The air cleaner filters should be checked before every start-up and after prolonged storage, the following steps should be done when checking air cleaner filters;

1. Remove the wing nut (B) Fig.3, lift to remove the air cleaner cover (A) as shown.
2. Remove the wing nut and washer (D) Fig.3, lift and remove air filters (C) Fig.3 from its base. Remove the foam filter (A) Fig.4 from the paper filter (B), wash foam filter in kerosene, squeeze kerosene out, soak foam filter in engine oil and squeeze engine oil out.
3. In a well ventilated area, use pressurized air to blow dust out of the paper filter (B) from the side opposite the filter’s normal air flow (clean side).
4. Replace filters and replace the air cleaner filter cover. Secure all parts with wing nuts.

STARTING & STOPPING PROCEDURES

STARTING PROCEDURES
STARTING YOUR ENGINE
WARNING! Do not adjust or attempt maintenance of engine without consulting an authorized service center.
Never run engine indoors or in enclosed, poor ventilated areas, engine exhaust contains carbon monoxide, an odorless and deadly gas!
To safely start your engine, follow these steps (Fig.5).Note: No choke is required on warm engines. Pull the recoil starter handle until resistance is felt, then pull it out with a rapid full arm stroke. Let the starter rope rewind slowly, repeat if necessary. Allow engine to run at no load for 5 minutes upon each initial start-up to allow engine to stabilize. IF ENGINE OIL LEVEL IS TOO LOW, ENGINE WILL NOT START. CHECK OIL LEVEL AND ADD IF NECESSARY.
STOPPING PROCEDURES
STOPPING YOUR ENGINE

1. Move the throttle lever (refer to step 9, Fig.5) towards the right.
2. Turn the engine switch (refer to step 6, Fig.5) to the “OFF” position (upwards).
3. Close the fuel shut-off valve (refer to step 3, Fig.5) by moving it towards the left.
4. Follow storage instructions in this manual.

BREAK-IN PERIOD
To ensure proper engine operation, as well as extend the life of the engine, the following break-in instructions must be followed. The first 20 hours of operation are the most important.
For the first 3 hours of operation:

• Do not apply a heavy load.

• Do not operate engine at maximum speed.
  After 20 hours of operation:

• Change engine oil.

MAINTENANCE

MAINTAINING YOUR ENGINE
Engine Oil Replacement
Oil crankcase capacity: 0.6 litres (KCG-65), 1.1 litres (KCG-130).
Engine oil should be replaced after the first 20 hours of operation or after the first month of use, it should be replaced every 100 hours or 6 months after. To replace engine oil;

1. Loosen the oil gauge dipstick (A) Fig.6.

2. Place an oil pan underneath drain hex. bolt (B), remove hex. bolt (B) and drain oil.

3. Once all the oil has completely drained, retighten the hex. bolt (B).
   Recommended Engine Oil
   It is recommended to use SAE 10W30 4-stroke gasoline engine oil. For cold weather (below -15ºC) use SAE 5W30.

4. Fill with clean engine oil through the oil gauge dipstick hole, fill then check oil level until the oil level reaches 3/4 up the dipstick or until it reaches the bottom lip of the dipstick hole as shown in illustration above.

Inspecting, Replacing or Cleaning Spark Plug (F7TC or equivalent)
The spark plug should be checked every 100 hours of operation or every 6 months. To replace or clean spark plug;

1. Dismantle the spark plug cap (A) Fig.7 by pulling it off the spark plug (B). Using the supplied spark plug wrench, undo the spark plug by turning it counterclockwise.
2. Check to see if there is carbon sediment build-up, if so just remove it. If the carbon sediment is excessive, replace the spark plug.
3. Measure the electrodes clearance. See Fig.8. The spark plug electrode clearance should be between 0.7-0.8mm. If the clearance exceeds 0.8mm, replace the spark plug with an LD F7TC or equivalent (NGK BP6ES, Champion N9Y).
4. Reinstall spark plug in the reverse order.

Cleaning Deposit Cup and Fuel Strainer
Deposit Cup (A) Fig.9-

1. Push the fuel valve to the closed (left) position.
2. Remove centre deposit cup bolt (B) Fig.9 using a wrench. Place a pan under the deposit cup to catch any gasoline inside the carburetor.
3. Remove deposit cup (A) Fig.9 and o-ring (C), wash both in solvent.
4. Reinstall parts in reverse order.

Fuel Stainer (A) Fig.101)

1. Remove gasoline tank cap (A) Fig.10 and pull out the fuel strainer (B).
2. Clean fuel strainer in solvent.
3. reinstall parts in reverse order.

MAINTENANCE, STORAGE & TROUBLESHOOTING

MAINTENANCE SCHEDULE
After initial 20 hours of operation: Change engine oil.
Every 25 hours of operation thereafter: Clean/replace air filter. Inspect/clean spark plug.
Every 50 hours of operation: Change engine oil. Clean fuel strainer.
Every 100 hours of operation: replace spark plug. Replace air filter.
STORAGE
If you plan on storing your engine for an extended period of time, the following steps should be followed;

1. Add fuel stabilizer to fuel tank to minimize the formation of fuel gum deposits during storage.

2. Run engine at least 5 minutes after adding stabilizer to allow it to enter the fuel system.
   NOTE: If a fuel stabilizer is not used, all gasoline must be drained from the tank and carburetor to prevent gum deposits from forming on these parts and causing possible malfunction of the engine. To drain gasoline;

3. Turn fuel shut-off valve to the “OFF” position as shown in Fig.11.

4. Position a drain pan under the caburetor.

5. Remove drain hex. bolt (A) Fig.12 from the carburetor (B) and drain the fuel from the carburetor and hose.

6. Turn fuel shut-off valve to the “ON” position.

7. Drain fuel from tank.

8. Reinstall the carburetor drain hex. bolt once the fuel is completely drained.

9. Drain engine oil from engine as described in “Engine Oil Replacement”.

10. Gently pull the recoil starter handle to distribute oil into the cylinder, pull until resistance is felt.

11. Cover and store in a dry, well ventilated area.
    Note: To prevent corrosion or moisture build-up during storage, do not cover the engine with a poly-bag or similar material.

IF YOU ARE EXPERIENCING PROBLEMS, DO NOT RETURN TO THE RETAILER, CALL THIS TOLL-FREE NUMBER FOR SERVICE INFORMATION
1-877-636-4214

2. Ignition switch in “Off” position.
3. Faulty spark plug.
4. Choke in wrong position.
5. Fuel shut-off valve is closed.
6. Spark plug wire loose.
7. Cylinder not lubricated, after long  storage.| 1. Add fuel or oil.
2. Turn to “ON” position.
3. Replace spark plug.
4. Adjust choke accordingly.
5. Open fuel shut-off valve.
6. Attach wire to spark plug.
7) Pour tablespoon of oil into spark plug hole.
Crank engine a few times and try to start again.
Engine overheating| 1. Insufficient ventilation.| 1. Move to adequate supply of fresh air.
Engine misfires/backfires| 1. Spark plug wire loose.
2. Incorrect spark plug gap.
3. Intake valve stuck, choke stuck,
incorrect timing, clogged carburetor.| 1. Check wire connections.
2. Re-gap or replace spark plug.
3. Have a qualified technician diagnose and service engine.
Engine stops suddenly| 1. Low oil shutdown.| 1. Fill with engine oil to proper levels.

PARTS DIAGRAM & PARTS LISTS
Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.

https://manual-hub.com/

References

• Manual-Hub.com - Free PDF manuals!
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>