JATRHG YL-OB102 YL-OB101 EV Charging Station User Manual
- June 17, 2024
- JATRHG
Table of Contents
EV PowerBox
USER’S MANUAL
EV CHARGING STATION
Model: YL-OB102 YL-OB101
SELECT POWER
Click the button to select the required current, press and hold the
button for 2 seconds to confirm.
The current selection must be made before connecting it to the vehicle. You
cannot change the current while it is connected to the vehicle.
EV Charging Cable
TYPE 2 (IEC 62196-2 EU European standard)
Good to know
- This is a Level 1 / Level 2 EV charging cable only for EVs with Type 1/2 inlets. Don’t use it for EVs with other types of inlets.
- This cable has complicated internal structure. Any questions, please contact our Customer Service Manager at the first time. Please do not take it apart without any professional technical support
- Don’t use it in the water.
- This product is only for EV charging. Please don’t use it for any other affair, including hauling, binding and so on.
Cautions
- Only used for EV charging
- Do not use the charging box if the device is damaged
- Do not use this device with an extension cord or adapter
- Please do not open up any part of the device by yourself. Please do not disconnect while the charging box is working
- Please follow the user manual to use this device
Professional specification
Service Life: > 10000 times
Insulation Resistance: > 1000M 0
Terminal Temperature rise: <50K
Contact Impedance: 0.5m 0
Max Working Temperature: -30°C —+ 50°C
Sealing gasket: rubber or silicon rubber
Withstand Voltage: 2000V
Inlet cable spec: 32.5mrriz(YL-OB102Y) 36mrriz(YL-OB101)
Shell Material: ABS+PC Alloy
Cable diameter: 12(mm) / 0.47(in)
Contact Pin: Copper alloy, silver or nickel plating
Vibration Resistance: Meet JDQ 53.3 requirements
About Maintenance
In order to ensure the normal service life of the charger and reduce the risk,
maintenance must be performed within the specified time; the maintenance of
the equipment needs to be completed by professionals, with use of qualified
and safe maintenance tools.
- The product is carefully packed in factory. During transportation, strong impact and bumps should be avoided to prevent damage to the outer packaging of the product.
- The product should be placed at an ambient temperature of -30°C —+50°C with a relative humidity of less than 95%.
The ambient air should not contain acids, alkalis or other corrosive gases and
explosive gases, It also should be away from rain, snow, wind and
sand.
Product instruction
Indicator status:
LED white stripe always bright: Normal power on : LED Green flow: Charging LED
Green fixed: Charging complete Yellow light bar 0.5S shiny: Faut courant
Yellow light bar 1.5s shiny: Faut temperature alarm Yellow light bar 2S shiny:
Faut electric leakage Yellow light bar 4S shiny: Faut overvoltage/
undervoltage Make an appointment to charge
Enter the appointment charging interface, tap the power button once for one
hour, and so on, after selecting the appointment charging time, press and hold
for 3 seconds to confirm, the interface pops up, that is, the setting is
complete, if the battery is fully charged, the charger will automatically stop
charging to prevent overcharging
Grounding selection
There are grounding charging and grounding-free charging when entering the
interface. Touch the power button to select and press and hold for 3 seconds,
and the interface will pop up, that is, the setting is complete.
Security Warning
Failure to follow instructions may result in danger!
- Regularly check whether the portable charger has visible damage, there may be an electric shock hazard when using the damaged product.
- Make sure that all safety facilities are available at all times and test then regularly to ensure safety.
- If a ‘Ground Error’ occurs, it must be assumed that the earth wire carries voltage. Please check the circuit and make sure that there is no high-power available in the whole circuit system.
- Before powering on the device, please confirm that the device is properly grounded to avoid accidents.
- All metal parts should be insulated to prevent short circuit caused by the touch of the tool with the metal frame.
- Do not modify, retrofit, or change any part by yourself under any circumstances.
- To ensure a stable service life and operation of the charging cable, operation enviroment should be kept clean and with constant temperature and humidity. The charging cable must not be used in the presence of volatile gas or flammable atmosphere.
Please confirm that the input voltage, frequency, circuit breakers and other conditions of the device have already met the specifications before the device is powered on.
TAMITO SAS
176 avenue charles de gaulles,
92200 Neuilly-sur-seine, FR
service@tamito.fr
CE No: HX220302011118
For more information and video tutorials about using and installation of the
EV charger, please visit our website:
www.jatrhg.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>