GT-Lite GT-501RF-S Rechargeable Flashlight Power Pack User Manual

**GT-Lite GT-501RF-S Rechargeable Flashlight Power Pack User Manual

**

RECHARGEABLE FLASHLIGHT/POWERPACK CONT.:

To  switch hook to opposite side of the flashlight:

1.  Snap the hook and crossbar out of the J hooks.

2. Swivel J hooks to back side of flashlight.

3. Snap hook and crossbar back into J hooks.
   

4. Hang anywhere!

• Do not look directly at the LED lights for any length of time.
• Do not shine the light directly into other people’s eyes.
• Do not remove protective lens covering LED lights.

This product is guaranteed against failure due to factory defects in materials or workmanship for one (1) year from the date of purchase. This warranty is non-transferable and applies only to the original owner. Proof of purchase required for repair or replacement. This warranty does not cover normal wear of parts or damage resulting from any misuse of the product. Misuse of the product includes but is not limited to: using in extreme weather conditions, opening the housing of the product, or attempted remodel/alterations made to product.

Assembly & Installation: GT-501RF-S | 2000/1000LM Worklight w/ Flashlight

WARNING

• When using product, basic precautions should always be followed.
•  Read and follow these instructions and observe all warnings.
• Carefully read and understand the information given in this manual before beginning installation. Failure to do so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal.
• Save these instructions and warnings.

CAUTION

• This item is damp rated. NEVER submerge this product in water!
• Do not use in on hot surfaces.
• Do not remove the lens protecting the LED.
• Do not use in areas near a gas source.
• It is NOT possible to change the LED light source.
• This light is not intended for use in potentially explosive environments.
• This is NOT a vapor proof light.
• Do not dismantle this light. The LED chips are not replaceable.
• This work light is NOT A TOY and is not suitable for use by children.

LITHIUM ION BATTERY

•  This item uses a rechargeable Lithium-ion battery that can rupture,
  ignite, and cause serious injury if being used improperly. – Please put the water protection cap on socket (14) after charging.

• DO NOT plug the unit into outdoor outlets. Keep charging unit dry.

• DO NOT place battery or device in fire or high temperatures.

• DO NOT immerse in or expose the battery to water.

• DO NOT puncture or damage the battery.

• DO NOT attempt to change the battery/use a different battery.

• Only charge this light with the charger supplied. Any attempt to
  substitute charger will void the warranty and may cause damage to the light, explosion, or fire.

• For prolonged battery life, do not store the light with a completely dead battery.

• For prolong battery life, we recommend that the light is switched OFF when connected to charging device, and is removed from the charger once battery is full.

• Charge the light every 3-6 months when not in use.

COMPONENTS:

A. Hook
B. Handle
C. LEDS
D. Rechargeable Battery Bank & LED Flashlight
E. Battery Fixation Clip
F. ON/OFF Switch
G. Side Knobs
H. Power Port
I. U Shaped Base
J. Base Affixing Bolt
K. H Shaped Base
L. USB Socket
M. Water-Proof Cap
N. Charging Socket
O. AC Charger
P. DC Charger
Q. USB Cable

ASSEMBLY:

1. Fasten light in upright position by tightening knobs on the side of the light (G).
2. Position center hole of U shaped base (1) over center hole of H shaped base (K).
3. Screw base affixing bolt (J) through (1) and (K) to tighten and assemble base.
4. Slide in the battery pack through the rail on the back side of the light. Allow battery fixation clip (E) to click into place.

TO USE:

1. Assemble the light and insert the battery.
2. Charge the battery pack by plugging the included power adapter into designated charging port
   • Red indication light shows that the product is charging
   • Green indication light signals a full charge Indicator Light when not
3.  Adjust the light angle to desired position by tightening side knobs (G)
4. If desired, use 360° hanging hook (A) to place light at appropriate location. Never use the product power cord or any other electrical cord to hang product.
5. Power ON by pushing (F) once to turn on High 2000LM.
6. Press button again to change light beam to low 1000LM Mode.
7. Press button again to power OFF.
8. Press button for 2 seconds to switch from front worklight to flashlight.
9. Press button again to switch from high 300LM to low 150LM on flashlight.
10. Press button again to power off.

RECHARGEABLE FLASHLIGHT/POWERPACK USE:

1. Remove battery pack/flashlight to use and/or hang anywhere.
2. It is possible to remove the hanging hook on the powerpack, and switch it to the opposite side, to aim flashlight in any direction. See figures 3.
3. Charge devices using the USB port with the appropriate cable for your device.
4. Do not store the battery completely dead. Keep battery at least partially charged at all times to prolong the life of the battery.
   

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>