GT-Lite GT-2PK-T8-3IN1 Complete LED Lighting Solutions Instruction Manual

GT-Lite GT-2PK-T8-3IN1 Complete LED Lighting Solutions

WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK,SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE

Assembly & Installation: GT-2PK-T8-3IN1 | T8 LED Tube 5000k (2pk)

WARNING

• When using product, basic precautions should always be followed.
• Read and follow these instructions and heed all warnings.
• Carefully read and understand the information given in this manual before beginning installation. Failure to do so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal.
• Save these instructions and warnings.

CAUTION

IF NOT QUALIFIED DO NOT ATTEMPT INSTALLATION

• Contact a certified electrician to install these bulbs if you are not properly qualified.

Risk of Electric Shock or Fire

• Risk of Electric Shock or is present when working with electrical components.
• Do not drill holes in the fixture that could affect the internal wiring.

Prevent Electric Wire Abrasions

• Do not expose wiring to edges of the fixture or other sharp objects. This can cause abrasion and damage the wiring, greatly increasing risk of electrical shock or fire.

Fixture Compatibility

• These bulbs are should only be installed in fixtures compatible with 48″ T8 Luminaires
• This lamp can be used with shunted and non-shunted lamp holders, but requires different wiring schematics for each type of lampholder (included)
• This bulb can be installed on electronic instant-start ballasts, electronic rapid-start ballasts, ballast bypass fixtures as well as magnetic ballast fixtures.
  It is your responsibility to check to make sure that this bulb is compatible with your light fixture.

CAUTION

• If the lamp or luminaire exhibits undesireable operation (buzzing, flickering, etc.) immediately turn off power, remove lamp from the luminaire, and contact manufacturer.
• Risk of fire. Perform a visual inspection to ensure lampholders are not damaged or loose before installing and turning on this lamp.
• If lamp does not light when the luminare is energized, remove lamp from luminaire and contact lamp manufacturer or qualified electrician.
• Reliable operating temperature: -4°F to +113°F (-20°C to +45°C).
• These devices are not intended for use with emergency exit lights.
• This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communication equipment operating between 0.45 – 30MHZ.

BASIC INSTALLATION DIAGRAM

BALLAST BYPASS RETROFIT INSTRUCTIONS:

1. TURN OFF POWER AT THE BREAKER OR FUSE PANEL. TURNING OFF POWER AT THE WALL SWITCH IS NOT SUFFICIENT SAFETY PRECAUTION

2. Double check the rating of the lamp (120-27/VAC) matches the voltage of the current circuit

3. Check to see if the fixture has shunted, or non-shunted lamp holders

4. Take out old bulbs and remove the ballast cover

5. Disconnect all wires attached to the ballast as close to the ballast as possible. It is best practice to leave the ballasts in place after doing this.

6. For Non-Shunted Lampholders:

   • Connect one wire from each lampholder at only one end of the fixture to the back wire.
     Separately connect the neutral wire (white) to the lampholder after.

   • At the opposite end of the fixture cut all wires that connect to that lampholder.

   • ENSURE THIS FIXTURE REMAINS GROUNDED AFTER THE RETROFIT PROCESS.

7. For Shunted Lampholders:

   • Connect one black wire to one lamp holder on one side of the light. Connect the neutral (white) wire to a lamp holder on the opposite side of light. Do this for each bulb in light fixture.

8. Replace any removed wiring covers or ballast covers.

9. Install GT-2PK-T8-3IN1 bulbs into the new fixture

EYE

• Do not look directly at the LED lights for any length of time.
• Do not remove protective lens covering LED lights.

GT-Lite Limited Warranty

This product is guaranteed against failure due to factory defects in material and workmanship for 5 years from the date of purchase. Warranty is non- transferrable and applies onty to the original owner. Warranty is based on 3 hours per day/7 days per week average when product is used as directed only. Warranty does not cover normal wear and tear of parts, or damage resulting from misuse of the product (i.e. using in extreme weather, alterations made to product, neglect, or abuse).

For refund or replacement, call GT-Lite at: 1-800-865-6799 or submit the form at http://gtledlighting.com/contact-us/Owner must provide proof of purchase and return lamp to GT-Lite to be considered for replacement or refund of original purchase price.
REPLACEMENT OR REFUND IS YOUR SOLE REMEDY, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY, LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states do not allow exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Contact GT-Lite 1-800-865-6799
WWW.GTLEDLIGHTING.com

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>