HORIZON FITNESS T100 Treadmill Award Winner Owner’s Manual

HORIZON FITNESS T100 Treadmill Award Winner

Product Information

Specifications:

• Model: T100
• Language: English

Important Precautions
When using an electrical product, basic precautions should always be followed, including the following:

• Read all instructions before using this treadmill.
• Ensure that all users of this treadmill are adequately informed of all warnings and precautions.
• Contact Customer Tech Support if you have any questions.
• This treadmill is intended for in-home use only. Do not use it in any commercial, rental, school, or institutional setting. Failure to comply will void the warranty.

Danger – To Reduce the Risk of Electrical Shock:
Always unplug the treadmill from the electrical outlet immediately after using, before cleaning, performing maintenance, and putting on or taking off parts.

Warning – To Reduce the Risk of Burns, Fire, Electrical Shock, or Injury to Persons:
Service technician:

• Use the treadmill only indoors, in a climate-controlled room.
• If the treadmill has been exposed to colder temperatures or high moisture climates, warm it up to room temperature before first-time use to prevent premature electronic failure.

Grounding Instructions:
This product must be grounded to reduce the risk of electrical shock. Follow these instructions:

• The treadmill is equipped with a cord having an equipment-grounding conductor and a grounding plug.
• The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with local codes and ordinances.
• Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
• Do not modify the plug provided with the product. If it does not fit the outlet, have a proper outlet installed by a qualified electrician.
• This product is for use on a nominal 110-120 Volt circuit and has a grounding plug. Make sure the product is connected to an outlet with the same configuration as the plug. Do not use an adapter.
• This product must be used on a dedicated circuit. Check if you are on a dedicated circuit by shutting off the power and observing if any other devices lose power. Move devices to a different circuit if necessary.
• This treadmill should be used with a minimum 15-amp circuit.

Product Usage Instructions

Follow these steps to use the treadmill:

1. Ensure the treadmill is placed in a climate-controlled room indoors.
2. Check if the treadmill has been exposed to colder temperatures or high moisture climates. If so, warm it up to room temperature before first-time use.
3. Read all instructions and precautions in the user manual.
4. Ensure all users are aware of the warnings and precautions.
5. Plug the treadmill into a properly grounded outlet with a dedicated circuit.
6. Turn on the power to the treadmill.
7. Follow the specific instructions for your desired exercise program or mode of operation.
8. After using the treadmill, unplug it from the electrical outlet.
9. Clean the treadmill as instructed in the user manual.
10. Perform regular maintenance tasks as recommended in the user manual.

FAQ

• Can I use this treadmill in a commercial or institutional setting?
  No, this treadmill is intended for in-home use only. Using it in commercial, rental, school, or institutional settings will void the warranty.

• What should I do if I have questions or need assistance?
  If you have any questions or need assistance, please contact Customer Tech Support at the number listed on the back panel of the OWNER’S MANUAL.

• How do I ground the treadmill?
  Follow the grounding instructions provided in the user manual. Ensure the treadmill is plugged into an appropriate outlet that is properly installed and grounded in accordance with local codes and ordinances.

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

• When using an electrical product, basic precautions should always be followed, including the following: Read all instructions before using this treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions. If you have any questions after reading this guide, contact Customer Tech Support at the number listed on the back panel of the OWNER’S MANUAL.
• This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting. Failure to comply will void the warranty.

DANGER
To reduce the risk of electrical shock:
Always unplug the treadmill from the electrical outlet immediately after using, before cleaning, performing maintenance and putting on or taking off parts.

WARNING
To reduce the risk of burns, fire, electrical shock or injury to persons :

• Never use the treadmill before securing the safety tether clip to your clothing.
• If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness, or shortness of breath, stop exercising immediately and consult your physician before continuing.
• When exercising, always maintain a comfortable pace.
• Do not wear clothes that might catch on any part of the treadmill.
• Always wear athletic shoes while using this equipment.
• Do not jump on the treadmill.
• At no time should more than one person be on treadmill while in operation.
• This treadmill should not be used by persons weighing more than specified in the OWNER’S MANUAL WARRANTY SECTION. Failure to comply will void the warranty.
• When lowering the treadmill deck, wait until rear feet are firmly on the floor before stepping on the deck.
• Disconnect all power before servicing or moving the equipment. To clean, wipe surfaces down with soap and slightly damp cloth only; never use solvents. (See MAINTENANCE)
• The treadmill should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or taking off parts.
• Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.
• Connect this exercise product to a properly grounded outlet only.

WARNING
To reduce the risk of burns, fire, electrical shock or injury to persons:

• At NO time should pets or children under the age of 13 be closer to the treadmill than 10 feet.
• At NO time should children under the age of 13 use the treadmill.
• Children over the age of 13 or disabled persons should not use the treadmill without adult supervision.
• Use the treadmill only for its intended use as described in the treadmill guide and owner’s manual.
• Do not use other attachments that are not recommended by the manufacturer. Attachments may cause injury.
• Never operate the treadmill if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or immersed in water. Return the treadmill to a service center for examination and repair.
• Keep power cord away from heated surfaces. Do not carry this unit by its supply cord or use the cord as a handle.
• Never operate the treadmill with the air opening blocked. Keep the air opening clean, free of lint, hair, and the like.
• To prevent electrical shock, never drop or insert any object into any opening.
• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.
• To disconnect, turn all controls to the off position, then remove plug from outlet.
• Do not use treadmill in any location that is not temperature controlled, such as but not limited to garages, porches, pool rooms, bathrooms, car ports or outdoors. Failure to comply may void the warranty.
• This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting. Failure to comply will void the warranty.
• Do not remove the console covers unless instructed by Customer Tech Support. Service should only be done by an authorized service technician
  It is essential that your treadmill is used only indoors, in a climate controlled room. If your treadmill has been exposed to colder temperatures or high moisture climates, it is strongly recommended that the treadmill is warmed up to room temperature before first time use. Failure to do so may cause premature electronic failure.

GROUNDING INSTRUCTIONS

• This product must be grounded. If a treadmill should malfunction or breakdown, grounding provides a path of least resistance for electrical current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with local codes and ordinances.
  DANGER
  Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

• This product is for use on a nominal 110-120 Volt circuit and has a grounding plug that looks like the plug in the illustration. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.

• This product must be used on a dedicated circuit. To determine if you are on a dedicated circuit, shut off the power to that circuit and observe if any other devices lose power. If so, move devices to a different circuit. Note: There are usually multiple outlets on one circuit. This treadmill should be used with a minimum 15-amp circuit. Note: There are usually multiple outlets on one circuit. This treadmill should be used with a minimum 15-amp circuit.
  WARNING

  • Connect this exercise product to a properly grounded outlet only.
  • Never operate product with a damaged cord or plug even if it is working properly. Never operate any product if it appears damaged, or has been immersed in water. Contact Customer Tech Support for replacement or repair.

ASSEMBLY

WARNING

• There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.

• Before proceeding, find your treadmill’s serial number located near the on/off
  power switch and power cord and enter it in the space provided below.

• ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:

Product Overview

TOOLS INCLUDED:

• 5 mm Allen Wrench
• 6 mm T-Wrench
• Screwdriver

PARTS INCLUDED:

• 1 Safety Key
• 2 Frame Extension Tubes
• 1 Console Assembly
• 2 Console Masts
•  1 Water Bottle Holder
• 2 Hand Grips
• 1 Deck Lock Pin
• 2 End Caps
• 6 Hardware Bags
• 1 Bottle of Silicone Lubricant
  NEED HELP?
  If you have questions or if there are any missing parts, contact Customer Tech Support. Contact information is located on the back panel of this manual.

PRE ASSEMBLY

UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side. Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled and in the upright folded position, with the lock latch secure. Unpack the unit where it will be used. Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill.

• WARNING
  DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill from packaging until specified to do so in the assembly instructions. You may remove the plastic wrap from console masts.

• WARNING
  FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!

• NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt.

• NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended.

ASSEMBLY

• STEP 1

  • Open hardware bag 1.
  • Slide the left frame extension tube onto the console mast support tube. Bolt in place using 2 SCREWS (A) on the side.
  • Repeat on the other side.

• STEP 2

  • Open hardware bag 2.
  • Slide the left console mast down onto the console mast support tube. Bolt in place using 2 bolts (b), 2 spring washers (c), and 2 flat washers (d) on the side. Then, bolt in place using 2 bolts (b), 2 spring washers (c), and 2 arc washers (e) on the front.
  • Repeat on the other side. On right console mast, the console cable must be threaded through the mast.
    Note : Do not completely tighten any screws or bolts until step 4 is complete!
    Note : Be careful not to pinch any wires while assembling the masts .

• STEP 3

  • Open hardware bag 3.
  • Insert left hand grip onto upright console mast.
  • Attach the left hand grip to the console mast using 2 bolts (b), 2 spring Washers (c) and 2 flat washers (d) from the inside and 1 bolt (b) and 1 arc washer (f) from the front.
  • Carefully thread the console cable through the hole in the right hand grip.
  • Attach the right hand grip as explained above in steps b–c.
    Note : Do not completely tighten any screws or bolts until step 4 is complete!
    Note : Be careful not to pinch any wires while assembling the masts.

• STEP 4

  • Open hardware bag 4.

  • Slide the console onto the hand grip posts.

  • Attach the hand grip posts to the console using 4 screws (g) and 4 arc washers (h) from the below the console.
    Note : Be careful not to pinch any wires while attaching the console.

  • Connect the console cables and carefully tuck wires in mast to avoid damage. Note: do not pinch console cable. Be sure the console cable prongs are aligned and the ends are tightly seated into each other.

  • Attach console cable cover.

  • Go back and completely tighten all bolts and screws from steps 1-4.
    

• STEP 5

  • Open hardware bag 5.
  • Attach deck lock pin to the left console mast using 2 screws (I).
  • Insert cup holder into right console pocket.

• STEP 6

  • Open hardware bag 6.
    Note : lock latch must be securely engaged before proceeding with assembly. (See folding instructions in treadmill guide .)

  • Attach the right end cap using 2 SCREWS (j). Repeat on the other side.

  • Connect power cord to a power outlet. The on /off switch is located next to the power cord. Flip this switch to the ‘ON’ position. You will hear a beep and the console will turn on.

  • Before the first use, lubricate the treadmill deck by following the instructions in the maintenance section in the treadmill guide .
    YOU ARE FINISHED!****

TREADMILL OPERATION

This section explains how to use your treadmill’s console and programming. The BASIC OPERATION section in the treadmill guide has instructions for the following:

• LOCATION OF THE TREADMILL
• Using the SAFETY KEY
• FOLD ING the trea dmi ll
• MOVING the trea dmi ll
• LEVELING the trea dmi ll
• TENSIONING THE RUNNING BELT
• CENTERING THE RUNNING BELT
• Using the HEART RATE function

CONSOLE OPERATION
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.

• A) Monitor dis play: Speed, time, pulse, distance, incline, and calories.
• B) Sto p: Press to pause/end your workout. Hold for 3 seconds to reset the treadmill.
• C) Start : Simply press to begin exercising or starts your program.
• D) Inc line adjust keys: Used to adjust incline in small increments (0.5% increments).
• E) Spee d adjust keys: Used to adjust speed in small increments (0.1 MPH increments).
• F) Quic k-adjust inc line keys: Used to reach desired incline more quickly.
• G) Quic k-adjust spee d keys: Used to reach desired speed more quickly.
• H) Safety key position : Enables treadmill when safety key is engaged.
• I) Program se lect key: Press key to select program.
• J) Time se lect key: Press to set desired workout time.
• K) Fan : Press to turn fan on / off.
• L) Water bott le / CD / MP3 ho lders : Holds personal workout equipment.
• M) CHANGE Dis plays key: Press to change display feedback during workout.

MONITOR DISPL AY

• Speed: Shown as MPH. Indicates how fast your walking or running surface is moving.
• Time : Shown as minutes:seconds. View the time remaining or the time elapsed in your workout.
• Pulse : Shown as beats per minute. Used to monitor your heart rate (displayed when contact is made with the pulse grips).
• Distance : Shown as miles. Indicates distance traveled during your workout.
• Incline : Shown as percent. Indicates the incline of your walking or running surface.
• Calories : Total calories burned during your workout.

Quick key operation
Once you have started your program you can use the quick keys to quickly change your speed and incline level. Press the number of your desired speed then press the start key. The start key confirms that this is the speed you want and the treadmill will adjust the speed or incline accordingly.

To reset console
Hold stop key for 3 seconds.

Finishing your wor kout
When your workout is complete, the monitor display will flash and beep. Your workout information will stay displayed on the console for 30 seconds and then reset.

Clear current se lection
To clear the current program selection or screen, hold the stop button for 5 seconds.

PROGRAMS

• P1 Manual : Allows “on the fly” manual speed and incline changes.
• P2 Rolling hills : Creates the feel of walking or running over hills.
• P3 Weight loss : Keeps user in their optimal fat burning zone.
• P4 Fat blast: Burn fat at an increased rate.
• P5 Cardio burn : Burns calories and tones muscles.
• P6 Endurance challenge : Tones muscle and challenges cardiovascular system.

GETTING STARTED/SELECTING A PROGRAM

1. Check to make sure no objects are placed on the belt that will hinder the movement of the treadmill.
2. Plug in the power cord and turn the treadmill ON.
3. Stand on the side rails of the treadmill.
4. Attach the safety key clip to part of your clothing.
5. Insert the safety key into the safety keyhole in the console.
6. You have two options to start your workout

• Quick start up
  Simply press the start key to begin working out. Or…

• Select a program

  • Press pro gram select key to choose a program.
  • Press time select key (use + / – keys for time intervals not shown on quick time select option).
  • Press start .

LIMITED HOME-USE WARRANTY

FRAME • LIFETIME
Horizon Fitness warrants the frame against defects in workmanship and materials for the lifetime of the owner, so long as the device remains in the possession of the original owner. (The frame is defined as the welded metal base of the unit and does not include any parts that can be removed.)

DRIVE MOTOR/ELEVATION • 7 YEARS
Horizon Fitness warrants the drive/elevation motor against defects in workmanship and materials for a period of 7 years from the date of original purchase, so long as the device remains in the possession of the original owner. Labor or installation of motor is not covered under the motor warranty.

ELECTRONICS & PARTS • 90 DAYS
Horizon Fitness warrants the electronic components, finish and all original parts for a period of 90 days from the date of original purchase, so long as the device remains in the possession of the original owner.

LABOR • 90 DAYS
Horizon Fitness shall cover the labor cost for the repair of the device for a period of 90 days from the date of the original purchase, so long as the device remains in the possession of the original owner.

EXCLUSIONS AND LIMITATIONS

• Who IS covered:
  The original owner and is not transferable.

• What IS covered:
  Repair or replacement of a defective motor, electronic component, or defective part and is the sole remedy of the warranty.

What IS NOT covered:

• Normal wear and tear, improper assembly or maintenance, or installation of parts or accessories not originally intended or compatible with the equipment as sold.
• Damage or failure due to accident, abuse, corrosion, discoloration of paint or plastic, neglect, theft, vandalism, fire, flood, wind, lightning, freezing, or other natural disasters of any kind, power reduction, fluctuation or failure from whatever cause, unusual atmospheric conditions, collision, introduction of foreign objects into the covered unit, or modifications that are unauthorized or not recommended by Horizon Fitness.
• Incidental or consequential damages. Horizon Fitness is not responsible or liable for indirect, special or consequential damages, economic loss, loss of property, or profits, loss of enjoyment or use, or other consequential damages of whatsoever nature in connection with the purchase, use, repair or maintenance of the equipment.
• Equipment used for commercial purposes or any use other than a single family or Household, unless endorsed by Horizon Fitness for coverage.
• Equipment owned or operated outside the US and Canada.
• Delivery, assembly, installation, setup for original or replacement units or labor or other costs associated with removal or replacement of the covered unit.
• Any attempt to repair this equipment creates a risk of injury. Horizon Fitness is not responsible or liable for any damage, loss or liability arising from any personal injury incurred during the course of, or as a result of any repair or attempted repair of your fitness equipment by other than an authorized service technician. All repairs attempted by you on your fitness equipment are undertaken AT YOUR OWN RISK and Horizon Fitness shall have no liability for any injury to the person or property arising from such repairs.

SERVICE/RETURNS

• In-home service is available within 150 miles of the nearest authorized repair center (Mileage beyond 150 miles from an authorized service center is the responsibility of the consumer).
• All returns must be pre-authorized by Horizon Fitness.
• Horizon Fitness’ obligation under this warranty is limited to replacing or repairing, at Horizon Fitness’ option, the same or comparable model at one of its authorized service centers.
• A Horizon Fitness authorized service center must receive all equipment for which a warranty claim is made. This equipment must be received with all freight and other transportation charges prepaid, accompanied by sufficient proof of purchase.
• Replacement units, parts and electronic components reconditioned to As New Condition by Horizon Fitness or its vendors may sometimes be supplied as warranty replacement parts and constitute fulfillment of warranty terms.
• This warranty gives you specific legal rights, and your rights may vary from state to state.

References

• Horizon Fitness
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>