LD systems LD DAVE G4X Series Compact 2.1 PA Loudspeakers System User Manual

LD systems LD DAVE G4X Series Compact 2.1 PA Loudspeakers System User Manual

YOU MADE THE RIGHT CHOICE!

This device was developed and manufactured under high quality requirements to ensure many years of trouble-free operation. This is what LD Systems stands for with its name and many years of experience as a manufacturer of high- quality audio products. Please read these operating instructions carefully so that you can quickly and optimally use your new LD Systems product. You can find more information about LD Systems on our website WWW.LD- SYSTEMS.COM

ABOUT THIS MANUAL

• Read the safety instructions and the entire manual carefully before commissioning.
• Observe the warnings on the unit and in the operating instructions.
• Always keep the operating instructions within reach.
• If you sell or pass on the appliance, be sure to hand over these operating instructions as well, as they are an essential part of the product.

INTENDED USE

The product is a device for event technology!
The product has been developed for professional use in the field of event technology and is not suitable for use in households! Furthermore, this product is only intended for qualified users with specialist knowledge of event technology! Use of the product outside the specified technical data and operating conditions is considered improper use! Liability for damage and third party damage to persons and property due to non-intended use is excluded! The product is not suitable for:

•  People (including children) with reduced physical, sensory or mental abilities or lack of experience and knowledge.
• Children (Children must be instructed not to play with the device).

EXPLANATIONS OF TERMS AND SYMBOLS

1. DANGER: The word DANGER, possibly in combination with a symbol, indicates immediately dangerous situations or conditions for life and limb.
2. WARNING: The word WARNING, possibly in combination with a symbol, indicates potentially dangerous situations or conditions for life and limb
3. CAUTION: The word CAUTION, possibly in combination with a symbol, is used to indicate situations or conditions that may lead to injury.
4. ATTENTION : The word ATTENTION, possibly in combination with a symbol, refers to situations or states that can lead to damage to property and/or the environment.

 This symbol indicates hazards that can cause an electric shock.
 This symbol indicates danger spots or dangerous situations.
 This symbol indicates danger from hot surfaces.
 This symbol indicates danger from high volumes
 This symbol indicates supplementary information on the operation of the product.
 This symbol denotes a device that does not contain any user-serviceable parts.

SAFETY INSTRUCTIONS

  DANGER

1. . Do not open or modify the device.
2. If your device is no longer working properly, liquids or objects have gotten in side the device, or the device has been damaged in any other way, switch it off immediately and disconnect it from the power supply. This device may only be repaired by authorized specialist personnel.
3. For devices of protection class 1, the protective conductor must be connected correctly. Never interrupt the protective conductor. Protection class 2 devices do not have a protective conductor.
4. Ensure that live cables are not kinked or otherwise mechanically damaged.
5. Never bypass the device fuse.

WARNING

1. The device must not be put into operation if it shows obvious signs of damage.
2. The device may only be installed in a voltage-free state.
3. If the power cord of the device is damaged, the device must not be put into operation.
4. Permanently connected power cords may only be replaced by a qualified person.

**DANGER:**

1. Do not operate the device if it has been exposed to severe temperature fluctuations (e.g. after transport). Humidity and condensation could damage the device. Do not switch on the device until it has reached the ambient temperature.
2. Make sure that the voltage and frequency of the mains supply correspond to the values indicated on the device. If the device has a voltage selector switch, do not connect the device until this is set correctly. Only use suitable power cords.
3. To disconnect the device from the mains at all poles, it is not enough to press the on/offswitch on the device.
4. Ensure that the fuse used corresponds to the type printed on the device.
5. Make sure that appropriate measures against overvoltage (e.g. lightning) have beentaken.
6. Note the specified maximum output current on devices with a power out connection. Make sure that the total power consumption of all connected devices does not exceed the specified value.
7. Only replace pluggable power cords with original cables.

**DANGER:**

1. Danger of suffocation! Plastic bags and small parts must be kept out of the reach of people (including children) with reduced physical, sensory or mental abilities.
2. Danger from falling! Make sure the device is installed securely and cannot fall. Only use suitable tripods or attachments (especially for fixed installations). Make sure accessories are properly installed and secured. Make sure that the applicable safety regulations are observed.

**WARNING:**

1. Only use the device in the manner intended.
2. Only operate the device with the accessories recommended and intended by the manufacturer.
3. During installation, observe the safety regulations applicable in your country.
4. After connecting the unit, check all cable routes to avoid damage or accidents, e.g. due to tripping hazards.
5. Be sure to observe the specified minimum distance to normally flammable materials! Unless this is explicitly stated, the minimum distance is 0.3 m.

ATTENTION:

1. There is a risk of jamming with moving components such as mounting brackets or other moving components.

DANGER

1. Do not install or operate the device near radiators, heat registers, stoves or other heat sources. Make sure that the device is always installed in such a way that it is sufficiently cooled and cannot overheat.
2. Do not place any sources of ignition such as burning candles near the device.
3. Ventilation openings must not be covered and fans must not be blocked.
4. Use the original packaging or packaging provided by the manufacturer for transport.
5. Avoid shock or shock to the device.
6. Observe the IP protection class and the environmental conditions such as temperature and humidity according to the specification.
7. Devices can be continuously developed. In the event of deviating information on operating conditions, performance or other device properties between the operating instructions and the device labeling, the information on the device always has priority.
8. The device is not suitable for tropical climate zones and for operation above 2000 m  above sea level.

ATTENTION:

Connecting signal cables can result in significant noise interference. Make sure that devices connected to the output are muted during plugging. Otherwise, noise levels can cause damage.

ATTENTION HIGH VOLUMES WITH AUDIO PRODUCTS!

This device is intended for professional use. The commercial operation of this device is subject to the applicable national regulations and guidelines for accident prevention. Hearing damage due to high volumes and continuous exposure: The use of this product can generate high sound pressure levels (SPL) which can cause hearing damage. Avoid exposure to high volumes.

SIGNAL TRANSMISSION VIA RADIO (e.g. W-DMX or audio radio systems, Bluetooth):

The quality and performance of wireless signal transmissions generally depends on the environmental conditions.

Influence on the range and signal stability, for example:

• Shielding (e.g. masonry, metal structures, water)
• High radio traffic (e.g. strong W-LAN networks)
• Interference
• Electromagnetic radiation (e.g. LED video walls, dimmers)

All range specifications refer to free field use with visual contact without interference! The operation of transmitters is subject to official regulations. These can vary from region to region and must be checked by the operator before commissioning (e.g. radio frequency and transmission power).

WARNING:

Devices with wireless signal transmission are not suitable for operation in sensitive areas in which radio operation can lead to possible interactions. These include, for example:

• Hospitals, health centers or other healthcare facilities that perform patient treatments with specialized staff and equipment.
• Class I, II and III hazardous areas
• restricted areas
• military facilities
• airplanes or vehicles
• Areas where cell phone use is prohibite

NOTES FOR PORTABLE INDOOR DEVICES

1. Temporary operation! Event equipment is basically only designed for temporary operation.
2. Continuous operation or permanent installation can lead to impairment of the function and premature aging of the devices.

SCOPE OF DELIVERY

Remove the product from the packaging and remove all packaging material. Check that the delivery is complete and intact and notify your distributor immediately after purchase if the delivery is incomplete or damaged.

The scope of delivery of the product DAVE 18 G4X includes:

• 1x DAVE 18 G4X Subwoofer
• 2x DAVE 18 G4X Satellite
• Power cord
• Operating instructions

The scope of delivery of the product DAVE 15 G4X includes:

• 1x DAVE 15 G4X Subwoofer
• 2x DAVE 15 G4X Satellite
• Power cord
• Operating instructions

The scope of delivery of the product DAVE 12 G4X includes:

• 1x DAVE 12 G4X Subwoofer
• 2x DAVE 12 G4X Satellite
• Power cord
• Operating instructions

The scope of delivery of the product DAVE 10 G4X includes:

• 1x DAVE 10 G4X Subwoofer
• 2x DAVE 10 G4X Satellite
• Power cord
• Operating instructions

ASSEMBLY AND CABLING

**DANGER:**

Always place the speaker system in a suitable location on a sufficiently stable, level and horizontal surface. Make sure that the speaker system cannot fall off the edge of a stage (e.g. due to vibration). There is a risk that equipment that has not been set up and positioned correctly will fall over or down. This can cause serious injury or death.

For optimal sound distribution of the bass, position the subwoofer centrally between the two satellite speakers A . If a central position is not possible, the subwoofer can alternatively be positioned sideways B . Use the M20 flange on the top of the subwoofer to attach a distance rod. In both cases, select the DSP preset corresponding to the set-up variant (MODE SELECT, left symbol).

The DAVE 12, DAVE 15 and DAVE 18 G4X satellites have a dual tilt flange with 0° and 5° tilt. Use the 0° flange with a standing audience and adjust the height of the bottom edge of the satellites to approximately the head height of the audience. Use the 5° tilt flange with a seated audience. Pay attention to the maximum permissible load and height of the stands and spacer rods used (stands and spacer rods optionally available). The entire electronics with DSP and power amplifiers are located in the subwoofer of the DAVE G4X speaker systems, therefore a connection between subwoofer and satellites only has to be made using suitable speaker cables (optionally available, recommendation min. 2 x 1.5 mm²).


If the standard set-up of the DAVE G4X speaker system is not desired or possible, the set-up can be done with a distance rod and a stand fork mounted on the subwoofer C . In order to achieve an impressive stereo sound and to avoid unpleasant interference, select the DSP preset that corresponds to this setup variant (MODE SELECT, right symbol) and use the stereo input INPUT 3L / 4R for control (XLR/jack combo sockets or cinch sockets).

To set up 2 complete DAVE G4X speaker systems, positioned left and right in front of a stage, also use distance rods with stand forks mounted on the subwoofers D . For both systems, select the DSP preset that corresponds to this set-up variant (MODE SELECT, right symbol) and assign one mono channel each (e.g. INPUT 1, SELECT LINE) to the left and right line signal of a feed device (e.g. mixing console). The loudspeaker cables of a system should be crossed and connected to the satellites (right system in the example).

CONNECTIONS, CONTROLS AND INDICATORS

The connection and mixer sections of the DAVE G4X speaker systems are identical and are located on the rear of the corresponding subwoofers (representative DAVE 18 G4X).

1. POWER INPUT
   IEC mains socket with integrated fuse holder. A suitable power cord is included in the scope of delivery.
   IMPORTANT NOTE: Replace the fuse only with one of the same type and rating. Pay attention to the imprint on the housing. If the fuse blows repeatedly, please contact an authorised service centre.

2. POWER
   On/off switch. Always switch on the speaker system as the last unit in the signal chain and switch it off again as the first unit.

3. INPUT 1 / INPUT 2
   Audio inputs with combo sockets (XLR / 6.3 mm jack), which are suitable for both unbalanced and balanced cabling. The inputs are adjusted to the signal source using the SELECT button in the subwoofer’s  mixer section (LINE, HI-Z and MIC).

4. INPUT 3 L / INPUT 4 R
   Stereo line input with combo jacks (XLR / 6.3 mm jack), suitable for both unbalanced and balanced cabling. Connection for a keyboard or external mixer, etc.. Only use connections no. 4 and no. 5 alternatively.

5. RCA INPUT 3 L / INPUT 4 R
   Stereo line input with cinch sockets for connecting an audio player (CD player, MP3 player, tablet, etc.). Only use connections no. 4 and no. 5 as alternatives.

6. INPUT 5/6 SPDIF
   Digital stereo input in optical SPDIF format with TosLink socket. Connection for a playback device with optical SPDIF output.

7. SAT LEFT / SAT RIGHT
   Speakon compatible connectors for the corresponding DAVE G4X satellites.

8. INPUT 1 / INPUT 2
   Volume control for channels 1 and 2. Turning to the right increases the volume, turning to the left decreases it.
   
   

9. ELECT
   Adjustment to the signal source is done with the SELECT button. If necessary, press the button repeatedly to adjust the audio input to thecorresponding signal source. Select LINE for an audio signal with line level, HI-Z for connecting a guitar with pick-up and MIC for connecting a microphone (corresponding indicator field LINE, HI-Z or MIC lights up white) .

10. HIGH
    Control for raising (turn to the right) or lowering (turn to the left) the treble in channel 1 or channel 2. In the centre position (detent point), there is no influence on the audio signal.

11. LOW
    Knob for increasing (turn to the right) or decreasing (turn to the left) the bass in channel 1 or channel 2. In the middle position (detent point), the audio signal is not affected.

12. REVERB
    Level control for mixing the signal from channel 1 or channel 2 to the internal digital effects unit.

13. PRESET PLATE / LARGE / SMALL / OFF
    If necessary, press the PRESET button repeatedly to select the desired effect preset or to switch off the reverb effect. The corresponding indicator field of the three effects lights up white; when the reverb effect is switched off, none of the indicator fields light up.

14. INPUT 3/4
    Volume control for stereo channel 3/4. Turning to the right increases the volume, turning to the left decreases it.

15. INPUT 5/6
    Volume control for stereo channel 5/6. Turning to the right increases the volume, turning to the left decreases it.

16. SOURCE
    Button for selecting the signal source SPDIF or Bluetooth for channel 5/6. The corresponding display field lights up white.

17. HOLD TO LINK
    Press the HOLD TO LINK button for about 3 seconds to put the internal Bluetooth module into pairing standby, the connection to a previously paired device is disconnected. The Bluetooth symbol flashes for the duration of the pairing readiness. Activate Bluetooth on your playback device (smartphone, tablet, etc.) and select LD DAVEG4 in the Bluetooth menu. Pairing is now automatic; as soon as the devices are paired, the Bluetooth symbol lights up permanently. Audio playback via Bluetooth can now be started.

18. MODE SELECT
    Select the symbol corresponding to the set-up variant of the DAVE G4X speaker system using the SELECT button. This optimises the radiation pattern of the satellite speakers accordingly. The symbol for the selected set-up variant lights up white.

19. SUB
    Volume control for the subwoofer. Turning to the right increases the volume, turning to the left decreases it.

20. HIGH
    High shelf filter for adjusting the treble reproduction to the room acoustics (turn to the left = lowering, turn to the right = raising, centre position = no influence)

21. STATUS DISPLAY
    POWER:
    Lights up when the subwoofer is correctly connected to the mains and switched on.
    SIGNAL:
    Indicator for the mixer sum signal. The signal detection takes place before the MAIN volume control.
    LIMIT:
    Lights up when the speaker system is operated in the upper limit range. A short flash of the LIMIT indicator is not critical. To protect the system, an excessive signal level is gently reduced by the integrated limiter. If the LIMIT indicator lights up for a longer time or permanently, reduce the volume level. Failure to do so may result in distorted sound reproduction and damage to the speaker system.
    PROTECT:
    The PROTECT indicator lights up permanently if the system is overloaded or overheats. The integrated amplifiers are automatically muted. After reaching normal operating conditions, the unit switches back to normal operating mode after a few minutes and the PROTECT indicator goes out.

22. MAIN
    Adjust the overall volume. The subwoofer volume is also adjusted according to the setting on the SUB volume control. Turning to the right increases the volume, turning to the left decreases it.

CARE, MAINTENANCE AND REPAIR

To ensure the proper functioning of the unit in the long term, it must be cared for regularly and serviced as required. The need for care and maintenance depends on the intensity of use and the environment.

We generally recommend a visual inspection before each start-up. Furthermore, we recommend that you carry out all the maintenance measures listed below every 500 operating hours or, in the case of low intensity of use, after one year at the latest. Defects caused by inadequate care may result in limitations of the warranty claims.

CARE (CAN BE CARRIED OUT BY THE USER)

WARNING! Before carrying out any maintenance work, disconnect the power supply and, if possible, all appliance connections.

NOTE! Improper care can lead to impairment or even destruction of the unit.

1. Housing surfaces must be cleaned with a clean, damp cloth. Make sure that no moisture can penetrate the unit.
2. Air inlets and outlets must be regularly cleaned of dust and dirt. If compressed air is used, make sure that damage to the unit is prevented (e.g. fans must be blocked in this case).
3. Cables and plug contacts must be cleaned regularly and freed from dust and dirt.
4. In general, no cleaning agents, disinfectants or agents with an abrasiveeffect may be used for maintenance, otherwise the surface finish may be impaired. Especially solvents, such as alcohol, can impair the function of the housing seals.
5. Units should generally be stored in a dry place and protected from dust and dirt.

MAINTENANCE AND REPAIR (BY QUALIFIED PERSONNEL ONLY)

DANGER! There are live components in the unit. Even after disconnecting from the mains, residual voltage may still be present in the unit, e.g. due to charged capacitors.
NOTE! There are no assemblies in the unit that require maintenance by the user.
NOTE! Maintenance and repair work may only be carried out by specialist personnel authorised by the manufacturer. In case of doubt, contact the manufacturer.
NOTE! Improperly performed maintenance work can affect the warranty claim.

OPTIONAL ACCESSORIES

DAVE 10 G4X

• Trolley for subwoofer
  Item number LDD10G4XSUBBAG

• Bag for satellites
  Item number LDD10G4XSATBAG

• Bag & Trolley set
  Item number LDD10G4XBAGSET

• Stand
  Item number LDD10G4XSTAND

• Dual stand
  Item number LDD10G4XDSTAND

DAVE 12 G4X

• Castor board
  Item number LDD12G4XCB

• Cover for satellite (piece)
  Item number LDD12G4XSATPC

• Cover for subwoofer
  Item number LDD12G4XSUBPC

• T-Bar
  Item number LDDG4XTBARL

DAVE 15 G4X

• Castor board
  Item number LDD15G4XCB

• Cover for satellite (piece)
  Item number LDD15G4XSATPC

• Cover for subwoofer
  Item number LDD15G4XSUBPC

• T-Bar
  Item number LDDG4XTBARL

DAVE 18 G4X

• Castor board
  Item number LDD18G4XCB

• Cover for satellite (piece)
  Item number LDD18G4XSATPC

• Cover for subwoofer
  Item number LDD18G4XSUBPC

• T-Bar
  Item number LDDG4XTBARL

TECHNICAL DATA

TECHNICAL DATA|
---|---
Item number| LDDAVE10G4X| LDDAVE12G4X| LDDAVE15G4X| LDDAVE18G4X
General| | | |
Weight| 24.5 Kg| 43.7 Kg| 53.9 Kg| 63.2 kg
Product type| PA Complete Systems| PA Complete Systems| PA Complete Systems| PA Complete Systems
Colour| Black| Black| Black| Black
System Power (RMS)| 340 W| 730 W| 1030 W| 2000 W
System Power (peak)| 680 W| 1460 W| 2060 W| 4000 W
Max. SPL (continuous)| 114 dB| 120 dB| 124 dB| 126 dB
Max. SPL (peak)| 120 dB| 127 dB| 130 dB| 134 dB
Frequency response| 37 Hz – 20000 Hz| 37 Hz – 20000 Hz| 33 Hz – 20000 Hz| 30 Hz – 20000 Hz
Crossover frequency| 110 Hz| 105 Hz| 105 Hz| 105 Hz
Dispersion (H x V)| 100° x 60°| 90° x 50°| 90° x 30°| 90° x 30°
Subwoofer| | | |
Woofer size| 10“| 12“| 15“| 18“
Woofer magnet| Ferrite| Ferrite| Ferrite| Ferrite
Woofer brand| Custom-made| Custom-made| Custom-made| Custom-made
Woofer voice coil| 2“| 2.5“| 3“| 4“
Woofer voice coil (mm)| 50 mm| 63 mm| 75 mm| 100 mm
Cabinet construction| Bass reflex| Bass reflex| Bass reflex| Bass reflex
Cabinet material| 15 mm/18 mm Multiplex| 15 mm/18 mm Multiplex| 15 mm/18 mm Multiplex| 15 mm/18 mm Multiplex
Cabinet surface| Polyurea| Polyurea| Polyurea| Polyurea
Subwoofer width| 350 mm| 450 mm| 515 mm| 545 mm
Subwoofer height| 436 mm| 505 mm| 575 mm| 640 mm
Subwoofer depth| 440 mm| 510 mm| 585 mm| 665 mm
Subwoofer features| 6 channel mixer, Bluetooth, SPDIF, Mono/Stereo Preset, 3 Reverb presets,M20| 6 channel mixer, Bluetooth, SPDIF, Mono/Stereo Preset, 3 Reverb presets,M20| 6 channel mixer, Bluetooth, SPDIF, Mono/Stereo Preset, 3 Reverb presets,M20| 6 channel mixer, Bluetooth, SPDIF, Mono/Stereo Preset, 3 Reverb presets,M20
Handles| 2| 2| 2| 2
Weight| 16.5 kg| 27.1 kg| 34.5 kg| 43.8 kg
Item number| LDDAVE10G4X| LDDAVE12G4X| LDDAVE15G4X| LDDAVE18G4X
---|---|---|---|---
Mid/Hi System
Midrange size| 2 x 4“| 6.5“| 8“| 8“
Midrange magnet| Ferrite| Ferrite| Ferrite| Ferrite
Midrange brand| Custom-made| Custom-made| Custom-made| Custom-made
Midrange voice coil| 1“| 1.5“| 1.5“| 2“
Midrange voice coil| 25.4 mm| 38.6 mm| 38.6 mm| 50 mm
Horn| CD Waveguide| CD Horn| CD Horn| CD Horn
Tweeter dimensions| 1“| 0.5“| 2 x 0.5“| 2 x 0.5“
Tweeter dimensions (mm)| 25.4 mm| 12.7 mm| 2 x 12.7 mm| 2 x 12.7 mm
Tweeter magnet| Neodym| Neodym| Neodym| Neodym
Tweeter brand| Custom-made| Custom-made| Custom-made| Custom-made
Tweeter voice coil| 1“| 1“| 1“| 1“
Tweeter voice coil (mm)| 25.4 mm| 25.4 mm| 25.4 mm| 25.4 mm
Mid/Hi system impedance| 4 Ohms| 4 Ohms| 4 Ohms| 4 Ohms
Loudspeaker inputs| 1| 1| 1| 1
Speaker input connections| Speakon compatible| Speakon compatible| Speakon compatible| Speakon compatible
Cabinet construction mid/high| Bass reflex| Bass reflex| Bass reflex| Bass reflex
Handles| Handles| Handles| Handles| Handles
Mid/Hi system cabinet material| 12 mm / 15 mm Multiplex| 12 mm / 15 mm Multiplex| 12 mm / 15 mm Multiplex| 12 mm / 15 mm Multiplex
Mid/Hi system cabinet surface| Polyurea| Polyurea| Polyurea| Polyurea
Mid/Hi system width| 150 mm| 252 mm| 275 mm| 275 mm
Mid/Hi system height| 345 mm| 435 mm| 470 mm| 470 mm
Mid/Hi system depth| 170 mm| 250 mm| 260 mm| 260 mm
Mid/Hi system features| Flange| 0° / 5° Flange, Midrange Waveguide| 0° / 5° Flange, Midrange Waveguide| 0° / 5° Flange, Midrange Waveguide
Weight| 4 kg| 8.3 kg| 9.7 kg| 9.7 Kg
Item number| LDDAVE10G4X| LDDAVE12G4X| LDDAVE15G4X| LDDAVE18G4X
---|---|---|---|---
Amplifier module (integrated in subwoofer)
Amplifier| Class D| Class D| Class D| Class D
Amplifier output (RMS| Subwoofer: 170 W, Satellites: 2 x 85 W| Subwoofer: 370 W, Satellites: 2 x 180 W| Subwoofer: 500 W, Satellites: 2 x 265 W| Subwoofer: 1000 W, Satellites: 2 x 500 W
Protection circuits| Limiter, overload, short circuit| Limiter, overload, short circuit| Limiter, overload, short circuit| Limiter, overload, short circuit
Cooling| Passive| Passive| Passive| Passive
Operating Temperature| 0 °C – 40 °C| 0 °C – 40 °C| 0 °C – 40 °C| 0 °C – 40 °C
Relative Humidity| < 80% (non-condensing)| < 80% (non-condensing)| < 80% (non- condensing)| v< 80% (non-condensing)
Controls| Power, Sub/High level, Main volume, Input volume, Input type, Mono mode, Reverb, Low/High EQ| Power, Sub/High level, Main volume, Input volume, Input type, Mono mode, Reverb, Low/High EQ| Power, Sub/High level, Main volume, Input volume, Input type, Mono mode, Reverb, Low/High EQ| Power, Sub/High level, Main volume, Input volume, Input type, Mono mode, Reverb, Low/High EQ
Indicators| Protect, Limit, Signal, Power| Protect, Limit, Signal, Power| Protect, Limit, Signal, Power| Protect, Limit, Signal, Power
Power connector| IEC| IEC| IEC| IEC
Operating voltage| 100 VAC – 240 VAC| 100 VAC – 240 VAC| 100 VAC – 240 VAC| 100 VAC – 240 VAC
Power consumption| 120 W| 300 W| 400 W| 600 W
Multi Inputs| 2 x Switchable (MIC, LINE, HI-Z)| 2 x Switchable (MIC, LINE, HI-Z)| 2 x Switchable (MIC, LINE, HI-Z)| 2 x Switchable (MIC, LINE, HI-Z)
Multi Input connectors| Combo-XLR| Combo-XLR| Combo-XLR| Combo-XLR
Line Inputs| 2| 2| 2| 2
Line Input connectors| Combo-XLR, RCA| Combo-XLR, RCA| Combo-XLR, RCA| Combo- XLR, RCA
Digital Inputs| 2| 2| 2| 2
Digital Input connector| SPDIF| SPDIF| SPDIF| SPDIF
Loudspeaker outputs| 2| 2| 2| 2
Speaker output connections| Speakon compatible| Speakon compatible|  Speakon compatible|  Speakon compatible
Bluetooth-Profil| A2DP| A2DP| A2DP| A2DP
Bluetooth-AudioDecoder| SBC| SBC| SBC| SBC

DISPOSAL

Packing:

1. Packaging can be fed into the recycling system via the usual disposal channels.
2. Please separate the packaging according to the disposal laws and recycling regulations in your country.

Device:

1. This appliance is subject to the European Directive on Waste Electrical and Electronic Equipment as amended. WEEE Directive Waste Electrical and Electronical Equipment. Old appliances and batteries do not belong in household waste. The old appliance or batteries must be disposed of via an approved waste disposal company or a municipal waste disposal facility. Please observe applicable regulations in your country!
2. Observe all disposal laws applicable in your country.
3. As a private customer, you can obtain information on environmentally friendly disposal options from the dealer from whom the product was purchased or from the relevant regional authorities.

Batteries and rechargeable batteries:

1. Batteries and rechargeable batteries do not belong in household waste. Batteries and rechargeable batteries must be disposed of via an authorised disposal company or a municipal disposal facility.
2. Observe all disposal laws and regulations applicable in your country.
3. As a private customer, you can obtain information on environmentally friendly disposal options from the dealer from whom the product was purchased or from the relevant regional authorities.
4. Appliances with batteries or accumulators that cannot be removed by the user must be handed in at a collection point for electrical appliances.

MANUFACTURER’S DECLARATIONS

MANUFACTURER’S WARRANTY & LIMITATION OF LIABILITY 

Adam Hall GmbH, Adam-Hall-Str. 1, D-61267 Neu Anspach / E-Mail Info@adamhall.com / +49 (0)6081 / 9419-0. Our current warranty conditions and limitation of liability can be found at:
https://cdnshop.adamhall.com/media/pdf/MANUFACTURERSDECLARATIONS_LD_SYSTEMS.pdf. In case of service, please contact your sales partner.

UKCA- CONFORMITY

Hereby, Adam Hall Ltd. declares that this product meets the following guidelines (where applicable)
Electrical Equipment (Safety) Regulations 2016
Electromagnetic Compatibility Regulations 2016 (SI 2016/1091)
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment
Regulation 2012 (SI 2012/3032)
Radio Equipment Regulations 201 7(SI 2016/2015)

UKCA- DECLARATION OF CONFORMITY

Products that are subject to Electrical Equipment(Safety)Regulation 2016, EMC Regulation 2016 or RoHS Regulation can be requested at info@adamhall.com. Products that are subject to the Radio Equipments Regulations 2017 (SI2017/1206) can be downloaded from www.adamhall.com/compliance/

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   • This device may not cause harmful interference, and
   • This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

RADIATION EXPOSURE STATEMENT

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
  • This device may not cause interference.
  • This device must accept any interference, including interference that may cause undesired operation of the device.
• This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Costumer Support

Adam Hall GmbH | Adam-Hall-Str. 1 | 61267 Neu-Anspach | Germany
Phone: +49 6081 9419-0 | adamhall.com
Adam Hall Ltd. | The Seedbed Business Centre | SS3 9QY Essex | UK

References

• Eventtechnik Lösungen | Adam Hall Group
• LD Systems® | Your Sound. Our Mission.
• Downloads | Service | Adam Hall Shop
• LD Systems® | Your Sound. Our Mission.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>