edgenectar Odge5000d 4T4R Digital Radios User Manual

edgenectar Odge5000d 4T4R Digital Radios

Specifications

• Model : Odge5000d
• Component type : 4T4R Digital Radios
• Output Power : High
• Compliance : 5G NR Compliant
• Rating : Outdoor Rated

General
The Odge5000d components are designed for maximum safety and reliability when they are installed, used, and maintained by trained and qualified technicians in accordance with the procedures
and instructions contained in this manual. To ensure the safe operation of your system, always follow the safety and operational recommendations in this manual.

User Manual

Copyright © BTI 2020. All rights reserved. This document is protected by international copyright law and may not be reprinted, reproduced, copied, or utilized in whole or in part by any means including electronic, mechanical, or other means without the prior written consent of Edgenectar Inc..

• Whilst reasonable care has been taken by BTI to ensure the information contained herein is reasonably accurate, BTI Wireless shall not, under any circumstances be liable for any loss or damage (direct or consequential) suffered by any party because of the contents of this publication or the reliance of any party thereon or any inaccuracy or omission therein. The information in this document is therefore provided on an “as is” basis without warranty and is subject to change without further notice and cannot be construed as a commitment by Edgenectar Inc..
• The products mentioned in this document are identified by the names, trademarks, service marks, and logos of their respective companies or organizations and may not be used in any advertising or publicity or in any other way
• whatsoever without the prior written consent of those companies or organizations and Edgenectar Inc.

4T4R Digital Radios High Output Power 5G NR Compliant Outdoor Rated
Copyright © 2021 Edgenectar Inc. All rights reserved.

General

The Odge5000d components are designed for maximum safety and reliability when they are installed, used, and maintained by trained and qualified technicians in accordance with the procedures and instructions contained in this manual. To
ensure the safe operation of your system, and always follow the safety and operational recommendations in this manual.

Warnings

• Odge5000d is not a consumer product. Please install and use Odge5000d in accordance with the instructions.
• Before installing or modifying any Odge5000d equipment, read and fully understand the entire instructions in this guide.
• Only qualified personnel are authorized to install and maintain the Odge5000d.
• Changes or modifications to the Odge5000d equipment not expressly approved by the manufacturer could void the product warranty and the user’s authority to operate the equipment.
• Follow Electro Static Discharge precautions to avoid any damage to PCB, PSU, etc.
• Keep equipment powered off during installation or modification.
• Low-path loss cables connected to antennas are highly recommended.
• Antenna gain should not exceed 14 dBi.
• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. –
• Consult the dealer or an experienced radio/TV technician for help.

Note : Only authorized persons can enter the area where the antenna is installed. The person is fully aware of the potential for exposure and can exercise control over his or her exposure by leaving the area or by some other
appropriate means. Awareness of the potential for RF exposure in a workplace or similar environment can be provided through specific training as part of an RF safety program Site

Considerations

• The system delay should be taken into consideration when there are neighboring BTS sites with overlapping in coverage.
• Pick an ideal easy-to-reach location for installation convenience.
• Verify that there is a minimum of a 200cm radius of space around Odge5000d system equipment for the convenience of maintenance and on-site inspection.

Environmental
Humidity and temperature have adverse effects on the reliability of the Odge5000d system. Therefore, it is highly recommended to install the equipment in locations with stable humidity, temperature, and ventilating.

The equipment has to operate within the following humidity level and temperature range

• Maximum humidity: 100%
• Temperature range: -40 to 55℃

Warning Marks

• The warning marks on the equipment shell should be kept clean, readable, and identifiable.

• ALWAYS disconnect all lines and power connections before servicing or disassembling this equipment.

• NEVER touch the surface after the device is powered on.

• For performance and safety reasons, NEVER disassemble and remodel the devices.

Preparation

Unpacking and Inspection
Unpack and inspect the packages as follows

1. Open the shipping packages carefully for each unit from the protective packing sponge.
2. Ensure that all equipment and accessories have been delivered.
3. Ensure that all equipment and accessories have no damage. If there is any damage, contact your BTI service agent.

Tools

An electric drill, cross-head screwdriver, side cutters, ladder, and other tools are needed for Odge5000d installation which is not offered by BTI for now. Customers are to provide these tools themselves.

Installation of the Odge5000d

Odge5000d Accessories

Wall Installation (Back on the Wall)

1. Attach and fasten the handle to the side of Odge5000d with screws M6×14 using T5 Wrench.
   

2. Attach and fasten the Bracket I to the back of Odge5000d with screws M6×14 using T5 Wrench.

3. Mark the position of the drilling holes in the mounting Bracket II. Note: R=13mm.

4. Drill 4 holes at the marked positions. Note: H=70mm
   

5. Attach the dowels, expansion screws, or the like, and fasten the Bracket II to the wall.
   Tips : use Bracket II as a reference to control each device’s separation distance before hanging and locking Odge5000d up.

6. Hang the Odge5000d on the mounting bracket II and fasten with nuts M10.
   

7. Fasten the Bracket I and II with screws M6×14.
   

8. Connect and lock the power cable at the Odge5000d rear side

9. Connect and screw the ground cable at the Odge5000d’s left side

Wall Installation (Side on the Wall)

1. Attach and fasten the handle to the side of Odge5000d with screws M6×14 using T5 Wrench.
   

2. Attach and fasten Bracket I to the left side of Odge5000d with screws M6×14 using a T5 Wrench.
   

3.  Mark the position of the drilling holes in the mounting Bracket II. Note : R=13mm.
   

4. Drill 4 holes at the marked positions. Note: H=70mm.
   

5. Attach the dowels, expansion screws or the like, and fasten the Bracket II to the wall.
   Tips : use Bracket II as a reference to control each device’s separation distance before hanging and locking Odge5000d up.
   

6. Hang the Odge5000d on the mounting bracket II and fasten with nuts M10.
   

7. Fasten the Bracket I and II with screws M6×14.
   

Pole Installation

1. Install the handle and Bracket I to the back of Odge5000d.
2. Install the bracket II and Bracket III to the pole.
3. Hang the Odge5000d on the mounting bracket and fasten with nuts M10.
4. Connect the ground cable and power cable.

Note : The diameter of the Pole shall not be over 110mm or less than 55mm.

changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note : This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.
If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING : This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 80 inches (200 cm) between the radiator and your body. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Copyright © 2021 Edgenectar Inc. All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>