KENWOOD KPG-22U USB Programming Interface Cable Instruction Manual
- June 16, 2024
- KENWOOD
Table of Contents
KENWOOD KPG-22U USB Programming Interface Cable
USB PROGRAMMING INTERFACE CABLE
Product Information
The USB Programming Interface Cable, models KPG-22U, KPG-36U,KPG-43U, and KPG- 46U, allows for easy programming of KENWOOD transceivers through a computer. It is compatible with Windows 7,Windows 8.1, and Windows 10 operating systems.
Supplied Items
- KPG-22U/36U/43U/46U driver
Operating System
The USB Programming Interface Cable is compatible with the following operating
systems:
- Windows 7
- Windows 8.1
- Windows 10
Note: It is recommended to use the cable in desktop mode as the driver installation software does not support touch input.
Installing the Driver
- When using the KPG-22U/36U/43U/46U for the first time, install the supplied driver.
- After the driver finishes copying to the PC, click the [Finish] button.
Note: The KPG-22U/36U/43U/46U is installed as a virtual com port and only supports programs used for KENWOOD transceivers.
Troubleshooting
If the driver cannot be installed or if, after installing the driver and
restarting your PC, the driver cannot be found or the operation does not
stabilize, try the following:
- Change the USB port to which you have connected the KPG-22U/36U/43U/46U.
- Remove other equipment attached to the USB ports of the PC.
For driver download information, visit http://www.kenwood.com/jp/usb-com/
Connecting to a PC and Transceiver
To connect the USB Programming Interface Cable to a PC and transceiver, follow
these steps:
- Connect the KPG-22U/36U/43U/46U USB connectors to the USB port of the PC.
- Connect the other connector to the transceiver.
Note: Connect the KPG-22U/36U/43U/46U directly to the transceiver and the PC (or USB HUB). Do not connect the KPG-22U/36U/43U/46U to any other device as it may cause malfunction.
Confirming the Installation
To confirm the installation of the USB Programming Interface Cable:
- Connect the KPG-22U/36U/43U/46U to a USB port.
- In the Device Manager, open the Port (COM and LPT).
- If “Silicon Labs CP210x USB to UART Bridge (COMx)” appears, the installation is complete.
Copyrights
The USB Programming Interface Cable may be subject to one or more of the
following statements:
- FCC WARNING: Unauthorized changes or modifications to this equipment may cause harmful interference.
- Information to the Digital Device User Required by the FCC:Proper recycling and waste disposal are encouraged to conserve resources and prevent detrimental effects on health and the environment.
FAQ
Q: Which operating systems are compatible with the USB Programming
Interface Cable?
A: The USB Programming Interface Cable is compatible with Windows 7,
Windows 8.1, and Windows 10 operating systems.
Q: Can I use the USB Programming Interface Cable with programs other than
those used for KENWOOD transceivers?
A: No, the USB Programming Interface Cable only supports programs used
for KENWOOD transceivers.
Q: What should I do if the driver cannot be installed or the operation
does not stabilize?
A: If you encounter issues with driver installation or unstable
operation, try changing the USB port to which you have connected the cable.
Additionally, remove other equipment attached to the USB ports of your PC.
Q: Where can I find the driver download information?
A: You can find the driver download information at
http://www.kenwood.com/jp/usb-com/
USB PROGRAMMING INTERFACE CABLE
KPG-22U KPG-36U
KPG-43U KPG-46U
INSTRUCTION
SUPPLIED ITEMS
-
USB programming interface cable (USB 2.0 compliant)
<cable length: 4.92 ft/ 1.5 m> -
CD (with driver software)
-
Instruction manual (B62-2326-XX)
OPERATING SYSTEM
Windows 7, Windows 8.1, or Windows 10 operating system.
(Use in desktop mode is recommended. The driver installation software does not
support touch input.)
INSTALLING THE DRIVER
When using the KPG-22U/ 36U/ 43U/ 46U for the fi rst time, install the supplied KPG-22U/ 36U/ 43U/ 46U driver.
ATTENTION:
- Applicable operating systems are subject to change without notice due to the end of the technical support by Microsoft Corporation or change of the product specifi cations.
- For Fpro software, use version 6.30 or later.
- Depending on the usage condition of the USB apparatus, saved content may be lost. JVC KENWOOD Corporation does not take responsibility for damages or lost content.
- Turn on the PC, then insert the supplied CD into the CD-ROM drive of the PC. Double-click the [CP210xVCPInstaller_x64.exe] or [CP210xVCPInstaller_x86.exe] fi le. When the Installation Wizard starts, click [Next>].
- Concerning the 64-bit version or 32-bit version, you should check the PC in advance.
- Read through the licensing agreement. If you consent to the terms of the agreement, check the “I accept this agreement”, then click [Next>].
- Start the installation.
- When the driver fi nishes copying to the PC, click the [Finish].
Note:
- The KPG-22U/ 36U/ 43U/ 46U is installed as a virtual com port.
- The KPG-22U/ 36U/ 43U/ 46U does not support programs other than those used for KENWOOD transceivers.
- If the driver cannot be installed or if, having installed the driver and restarted your PC, the driver cannot be found or the operation does not stabilize, try changing the USB port to that which you have connected the KPG-22U/ 36U/ 43U/ 46U. Additionally, try removing other equipment attached to the USB ports of the PC.
- Access the following URL for the driver download information: http://www.kenwood.com/jp/usb-com/
CONNECTING TO A PC AND TRANSCEIVER
Connect the KPG-22U/ 36U/ 43U/ 46U USB connectors to the USB port of the PC, and the other connector to the transceiver.
Note:
- Connect the KPG-22U/ 36U/ 43U/ 46U directly to the transceiver and the PC (or USB HUB).
- Do not connect the KPG-22U/ 36U/ 43U/ 46U other than PC (or USB HUB). It causes malfunction of the KPG-22U/ 36U/ 43U/ 46U and the transceiver.
CONFIRMING THE INSTALLATION
Connect the KPG-22U/ 36U/ 43U/ 46U to a USB port. In the “Device Manager”, open the “Port (COM and LPT)”. If “Silicon Labs CP210x USB to UART Bridge (COMx)” appears, installation is complete.
COPYRIGHTS
- Windows® is a registered trademark of Microsoft Corporation in the United States and/or other countries.
- Other product and company names mentioned herein may be the trademarks of their respective owners.
One or more of the following statements may be applicable to this equipment.
FCC WARNING
This equipment generates or uses radio frequency energy. Changes or modifi
cations to this equipment may cause harmful interference unless the modifi
cations are expressly approved by the party responsible/
JVC KENWOOD. The user could lose the authority to operate this equipment if an
unauthorized change or modifi cation is made.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer for technical assistance.
Information on Disposal of Old Electrical and Electronic Equipment and
Batteries (applicable for countries that have adopted separate waste
collection systems)
Products and batteries with the symbol (crossed-out wheeled bin) cannot be
disposed as household waste.
Old electrical and electronic equipment and batteries should be recycled at a
facility capable of handling these items and their waste byproducts.
Contact your local authority for details in locating a recycle facility
nearest to you.
Proper recycling and waste disposal will help conserve resources whilst
preventing detrimental effects on our health and the environment.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>