makita DDF458 Cordless Driver Drill Instruction Manual
- June 16, 2024
- Makita
Table of Contents
makita DDF458 Cordless Driver Drill
Specifications
- Model: DDF458
- Drilling into steel: 13 mm (1/2″)
- Capacities:
- Drilling into wood: 76 mm (3″)
- Fastening wood screw: 10 mm x 90 mm (3/8″ x 3-1/2″)
- Fastening machine screw: 6 mm (1/4″)
- No load speed (RPM): High (2) – 0 – 2,000/min, Low (1) – 0 – 400/min
- Overall length: 225 mm (8-7/8″)
- Net weight: 2.0 kg (4.4 lbs)
- Rated voltage: D.C. 18 V
- Standard battery cartridge:
- BL1815N / BL1820 / BL1820B
- BL1830 / BL1830B / BL1840 / BL1840B / BL1850 / BL1850B / BL1860
SPECIFICATIONS
| Model | DDF458 |
|---|
Capacities
| Drilling into steel| 13 mm (1/2″)
Drilling into wood| 76 mm (3″)
Fastening wood screw| 10 mm x 90 mm (3/8″ x 3-1/2″)
Fastening machine screw| 6 mm (1/4″)
No load speed (RPM)
| High (2)| 0 – 2,000 /min
Low (1)| 0 – 400 /min
Overall length| 225 mm (8-7/8″)
Net weight| 2.0 kg (4.4 lbs)| 2.3 kg (5.0 lbs)
Rated voltage| D.C. 18 V
Standard battery cartridge
| ****
BL1815N / BL1820 / BL1820B
| BL1830 / BL1830B / BL1840 / BL1840B / BL1850 / BL1850B / BL1860B
- Due to our continuing program of research and development, the specifications herein are subject to change without notice.
- Specifications and battery cartridge may differ from country to country.
- Weight, with battery cartridge, according to EPTA-Procedure 01/2003
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in electric shock, fire, and/or
serious injury.
Save all warnings and instructions for future reference. The term “power tool”
in the warnings refers to your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
Work area safety
-
Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
-
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks that may ignite the dust or fumes.
-
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety -
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
-
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
-
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock. -
When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
-
If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. The use of a GFCI reduces the risk of electric shock.
Personal safety -
Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
-
Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
-
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
-
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
-
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
-
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
-
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.
Power tool use and care -
Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
-
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
-
Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
-
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
-
Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
-
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
-
Use the power tool, accessories tool bits, etc. by these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Battery tool use and care -
Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
-
Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
-
When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
-
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts the eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Service -
Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
-
Follow instructions for lubricating and changing accessories.
-
Keep handles dry, clean, and free from oil and grease.
CORDLESS DRIVER DRILL SAFETY WARNINGS
-
Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
-
Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
-
Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
-
Always be sure you have a firm footing.
Be sure no one is below when using the tool in high locations. -
Hold the tool firmly.
-
Keep hands away from rotating parts.
-
Do not leave the tool running. Operate the tool only when hand-held.
-
Do not touch the drill bit or the workpiece immediately after the operation; they may be extremely hot and could burn your skin.
-
Some materials contain chemicals that may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity with the product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.
Symbols
The following shows the symbols used for the tool.
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CARTRIDGE
-
Before using the battery cartridge, read all instructions and cautionary markings on (1) the battery charger, (2) the battery, and (3) the product using the battery.
-
Do not disassemble the battery cartridge.
-
If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns, and even an explosion.
-
If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.
-
Do not short the battery cartridge:
- Do not touch the terminals with any conductive material.
- Avoid storing battery cartridges in a container with other metal objects such as nails, coins, etc.
- Do not expose the battery cartridge to water or rain.
A battery short can cause a large current flow, overheating, possible burns, and even a breakdown.
-
Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 ﾟ C (122 ﾟ F).
-
Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
-
Be careful not to drop or strike the battery.
-
Do not use a damaged battery.
-
Follow your local regulations relating to the disposal of batteries.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that have been altered, may
result in the battery bursting causing fires, personal injury, and damage. It
will also void the Makita warranty for the Makita tool and charger.
Tips for maintaining maximum battery life
-
Charge the battery cartridge before completely discharged.
Always stop tool operation and charge the battery cartridge when you notice less tool power. -
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life. -
Charge the battery cartridge at room temperature at 10 ﾟ C – 40 ﾟ C (50 ﾟ F – 104 ﾟ F). Let a hot battery cartridge cool down before charging it.
-
Charge the battery cartridge if you do not use it for a long period (more than six months).
FUNCTIONAL DESCRIPTION
CAUTION: Always be sure that the tool is switched off and the battery
cartridge is removed before adjusting or checking the function of the tool.
Installing or removing the battery cartridge
CAUTION:
- Always switch off the tool before installing or removing of the battery cartridge.
- Hold the tool and the battery cartridge firmly when installing or removing battery cartridge. Failure to hold the tool and the battery cartridge firmly may cause them to slip off your hands and result in damage to the tool and battery cartridge and a personal injury.
To remove the battery cartridge, slide it from the tool while sliding the
button on the front of the cartridge.
To install the battery cartridge, align the tongue on the battery cartridge
with the groove in the housing and slip it into place. Insert it all the way
until it locks in place with a little click. If you can see the red indicator
on the upper side of the button, it is not locked completely.
CAUTION:
- Always install the battery cartridge fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
- Do not install the battery cartridge forcibly. If the cartridge does not slide in easily, it is not being inserted correctly.
Battery protection system (Lithium-ion battery with star marking)
Lithium-ion batteries with a star marking are equipped with a protection
system. This system automatically cuts off power to the tool to extend battery
life.
The tool will automatically stop during operation if the tool and/or battery
are placed under one of the following conditions:
Overloaded:
- The tool is operated in a manner that causes it to draw an abnormally high current.
- In this situation, release the switch trigger on the tool and stop the application that caused the tool to become overloaded. Then pull the switch trigger again to restart.
- If the tool does not start, the battery is overheated. In this situation, let the battery cool before pulling the switch trigger again.
Low battery voltage:
The remaining battery capacity is too low and the tool will not operate. In
this situation, remove and recharge the battery
Indicating the remaining battery capacity
(Only for battery cartridges with “B” at the end of the model number.)
Press
the check button on the battery cartridge to indicate the remaining battery
capacity. The indicator lamps light up for few seconds.
NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity.
Switch action
CAUTION: Before inserting the battery cartridge into the tool, always
check to see that the switch trigger actuates properly and returns to the
“OFF” position when released.
To start the tool, simply pull the switch trigger. Tool speed is increased by
increasing pressure on the switch trigger. Release the switch trigger to stop.
Lighting up the front lamp
CAUTION: Do not look in the light or see the source of light directly.
Pull the switch trigger to light up the lamp. The lamp keeps on lighting while
the switch trigger is being pulled. The lamp goes out 10 -15 seconds after
releasing the trigger.
NOTE: Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination.
Reversing switch action
- This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation.
- When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled.
CAUTION:
- Always check the direction of rotation before operation.
- Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool.
- When not operating the tool, always set the reversing switch lever to the neutral position.
Speed change
To change the speed, first switch off the tool and then slide the speed change lever to the “2” side for high speed or, “1” side for low speed. Be sure that the speed change lever is set to the correct position before operation. Use the right speed for your job.
CAUTION:
- Always set the speed change lever fully to the correct position. If you operate the tool with the speed change lever positioned halfway between the “1” side and , “2” side, the tool may be damaged.
- Do not use the speed change lever while the tool is running. The tool may be damaged.
Selecting the action mode
This tool has an action mode-changing ring. For drilling, turn the ring so that the arrow on the tool body points toward the mark on the ring. For screwing, turn the ring so that the arrow points toward the mark on the ring.
CAUTION: Always set the ring correctly to your desired mode mark. If you operate the tool with the ring positioned halfway between the mode marks, the tool may be damaged.
Adjusting the fastening torque (screwdriver mode “ “)
The fastening torque can be adjusted in 21 steps by turning the adjusting ring so that its graduations are aligned with the pointer on the tool body.- First, slide the action mode change lever to the position of the symbol.
- The fastening torque is minimum when the number 1 is aligned with the pointer and maximum when the marking is aligned with the pointer. The clutch will slip at various torque levels when set at the number 1 to 21. Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which torque level is required for a particular application.
NOTE: The adjusting ring does not lock when the pointer is positioned only halfway between the graduations.
Empty signal for remaining battery capacity (specific country)
Only for tools with the button and LED indicator
Stop the tool and with the tool stopped press the button on the switch panel and the remaining battery capacity will be signaled on the panel.- The status displayed on the switch panel and the remaining battery capacity are shown in the following table
NOTE: Before checking the remaining battery capacity, be sure to stop the tool.
ASSEMBLY
CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.
Installing side grip (auxiliary handle)
Always use the side grip to ensure operating safety. Insert the side grip so that the protrusions on the grip base and steel band fit in between the grooves on the tool barrel. Then tighten the grip by turning clockwise. To change the angle of the side grip, loosen and remove the grip, then turn and insert it again.
Installing or removing the driver bit or drill bit
Turn the sleeve counterclockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Turn the sleeve clockwise to tighten the chuck. To remove the bit, turn the sleeve counterclockwise.
Installing bit holder
Fit the bit holder into the protrusion at the tool foot on either the right or left side and secure it with a screw. When not using the driver bit, keep it in the bit holders. Bits 45 mm long can be kept there.
Hook
- The hook is convenient for temporarily hanging the tool. This can be installed on either side of the tool.
- To install the hook, insert it into a groove in the tool housing on either side and then secure it with a screw. To remove, loosen the screw and then take it out.
OPERATION
Screwdriving operation
First, slide the action mode change lever so that it points to the marking.
Adjust the adjusting ring to the proper torque level for your work. Then
proceed as follows. Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then increase the speed
gradually. Release the switch trigger as soon as the clutch cuts in.
NOTE
- Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged.
- When driving a wood screw, predrill a pilot hole 2/3 the diameter of the screw. It makes driving easier and prevents the splitting of the workpiece.
- If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery.
Drilling operation
Drilling in wood
When drilling in wood, the best results are obtained with wood drills equipped
with a guide screw. The guide screw makes drilling easier by pulling the bit
into the workpiece.
Drilling in metal
- To prevent the bit from slipping when starting a hole, make an indentation with a center punch and hammer at the point to be drilled. Place the point of the bit in the indentation and start drilling.
- Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry. First, slide the action mode change lever so that it points to the marking. The adjusting ring can be aligned in any torque level for this operation. Then proceed as follows.
CAUTION:
- Pressing excessively on the tool will not speed up the drilling. This excessive pressure will only serve to damage the tip of your bit, decrease the tool performance, and shorten the service life of the tool.
- There is a tremendous force exerted on the tool/bit at the time of hole breakthrough. Hold the tool firmly and exert care when the bit begins to break through the workpiece.
- A stuck bit can be removed simply by setting the reversing switch to reverse rotation to back out. However, the tool may back out abruptly if you do not hold it firmly.
- Always secure small workpieces in a vise or similar hold-down device.
- If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery.
MAINTENANCE
CAUTION:
- Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance.
- Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.
Replacing carbon brushes
Replace when they wear down to the limit mark. Keep the carbon brushes clean
and free to slip in the holders. Both carbon brushes should be replaced at the
same time. Use only identical carbon brushes.
Use a screwdriver to remove two screws then remove the rear cover.
Raise the arm part of the spring and then place it in the recessed part of the brush holder with a slotted bit screwdriver of slender shaft or the like.
Use pliers to remove the carbon brush caps of the carbon brushes. Take out the
worn carbon brushes, insert the new ones.
- Make sure that the carbon brush caps fit into the holes in the brush holders securely.
- Reinstall the rear cover and tighten the two screws securely. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
- Drill bits
- Screw bits
- Hook
- Grip assembly
- Makita genuine battery and charger
- Rubber pad assembly
- Wool bonnet
- Foam polishing pad
- Battery protector
NOTE: Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the
factory. It is warranted to be free of defects from workmanship and materials
for ONE YEAR from the date of original purchase. Should any trouble develop
during this one-year period, return the COMPLETE tool, freight prepaid, to one
of Makita’s Factory or Authorized Service Centers. If inspection shows the
trouble is caused by defective workmanship or material, Makita will repair (or
at our option, replace) without charge.
This Warranty does not apply where:
- repairs have been made or attempted by others: repairs are required because of normal wear and tear:
- the tool has been abused, misused or improperly maintained:
- alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER
APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED
WARRANTIES OF “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,” AFTER
THE ONE-YEAR TERM OF THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other
rights that vary from state to state. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you.
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California to
cause cancer, birth defects, or other reproductive harm. Some examples of
these chemicals are:
- lead from lead-based paints,
- crystalline silica from bricks and cement and other masonry products, and
- arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
FAQ
- Q: What should I do if I need to operate the power tool in a damp location?
- A: If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply to reduce the risk of electric shock.
- Q: Can I use any battery charger to recharge the battery cartridge?
- A: No, you should only recharge the battery cartridge with the charger specified by the manufacturer. Using an incompatible charger may cause damage or hazards.
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446-8502 Japan
www.32.makita.com
References
- MAKITA Industrial Power Tools - The Leader In Cordless with 18V LXT Lithium-Ion
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>