MEGA LITE 5201 LED Circa Scoop Light User Manual

: June 16, 2024
: MEGA LITE

MEGA LITE 5201 LED Circa Scoop Light

Product Information

Specifications

DMX Connectors: 5-pin XLR Connectors
Power Connectors: Power Con Type
Mounting Yoke: Square Yoke
Thermal: Fastening System: Single Quick Release Clamp Mounts
Flight Case: CAS-5199-4 Quad Road Case
LED Quantity: 84 RGB, 12 Warm White, 45 Warm White + Amber
Fuse: 5×20 F5AL250V
LED Angle
Power Input Voltage: 110V-240 50/60 Hz
Ballast: Electronic auto switching
Power Consumption: Watts: 93 Amps: 1.30
LED Lifetime: *60 to 100 thousand hours
Scan Rate: 7000Hz
SMD LEDS Watts: 0.8 Watt each
DMX 512 Protocol DMX Modes:
Control Options: 5 Mode of Operation
Mode 2 Channel Dimmer, Macro Mode 3 Channel Dimmer, Warm White, Amber Mode 9 Channel Outer R,G, B, Inner R,G,B, Warm White, Amber, Reflective Warm White Mode 14 Channel Dimmer, Outer R,G,B, Outer Strobe, Inner R,G,B, Inner Strobe, Warm White, Amber, Center Strobe Reflective Center, Reflective Strobe Mode 17 Channel Dimmer, Outer R,G,B, Macro, Macro Speed, Outer Strobe, Inner R,G,B, Macro, Macro Speed, Inner Strobe, Warm White, Amber, Reflective Center, Center Strobe
Display Control /60 HZ
Fixture Size: 13.5 X 7.3 X 14.12
Fixture Weight: 8lb
Packaged Size: 16.5 X 11 X 17
Packaged Weight: 12lb

Electrical Specifications

MEGA-LITE-5201-LED-Circa-Scoop-Light-FIG-1

Control & Programming

MEGA-LITE-5201-LED-Circa-Scoop-Light-FIG-2

Product Usage Instructions

Protection Against Fire

Disconnect power before lamp replacement or servicing.
For connection to main power supply proceed to page 6.
This unit must be earthed (electronically grounded).
Do not expose unit to rain or moisture.
Unit must not be left on for a long period of time.

Protection Against Electrical Damage

Use safety chain when hanging unit.
Use quality clamps or bolts when positioning unit.
Do not open unit risk of electrical shock.

Main Power Connection

Caution!

Do not connect fixture to a dimmer system.
This unit must be earthed (electronically grounded).
Replace fuse only with the specified type and rating.
Power link maximum 10 units at 110V.

This device is equipped with an auto switching power supply that will allow you to work from 100V-240V 50/60Hz.

The occupation of the connection-cable is as follows:

MEGA-LITE-5201-LED-Circa-Scoop-Light-FIG-3

DMX-512 Connection

The fixture is equipped with 5 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a shielded twisted pair cable designed for RS-485 and 5 pin XLR plugs and connectors in order to connect the controller with the fixture or the fixture with another.

MEGA-LITE-5201-LED-Circa-Scoop-Light-FIG-5

DMX–Input

Shield
Signal (-)
Signal (+)
N/A
N/A

DMX–Output

Shield
Signal (-)
Signal (+)
N/A
N/A

Caution!

At the last fixture, the DMX signal needs to be terminated with a terminator. Solder a 120 Ohm resistor between the (-) and the (+) signal into a 5 pin XLR plug and plug it into the last fixture on the signal run. Pre-manufactured terminator plugs are available for purchase from your Mega-Lite dealer (P-DMX-T).

Size

MEGA-LITE-5201-LED-Circa-Scoop-Light-FIG-3

Display Control

MEGA-LITE-5201-LED-Circa-Scoop-Light-FIG-6 MEGA-
LITE-5201-LED-Circa-Scoop-Light-FIG-7

Ringing the fixture

Caution!

The installations must be carried out by an authorized dealer or trained professional.
Unit may cause severe injures if you have doubts concerning the safety do not install.
Unit is to be 24inches away from flammable materials (decoration material)
Use high quality installation equipment to hang unit.

When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the projector has got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be checked at least one time a year by a skilled person.

DMX Profile

MEGA-LITE-5201-LED-Circa-Scoop-Light-FIG-10

Cleaning and Maintenance

Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:

All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
Mechanically moved parts like axles and other must not show any traces of wearing and must not rotate with unbal-ances.
The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed.

Disconnect from mains before starting maintenance operation!

Caution Danger to life

We recommend a frequent cleaning of the device. Please use a moist, lint free cloth. Never use alcohol or solvents!

The objective lens will require periodic cleaning on usage and environment. Environment with foggers will require more periodic cleaning as fog fluid tends to build up residues, reducing the light output.
The cooling-fans should be cleaned monthly. DO NOT blow high pressure air into fans as incorrect rotation can damage the fans operation.
The gobos, dichroic color filters and internal lenses may be cleaned with soft brush using soapy water.
The interior of the fixture should be cleaned using a vacuum.
We recommend proper lubrication of the motor wheel. The quantity of the oil must not be excessive in order to avoid oil run outs when motor wheel rotate.

Note: There is no serviceable parts inside the device except for the fuse.

Maintenance and service operations are to be carried out by authorized dealers.

Replacing the fuse: Only replace the fuse with the same type and rating.

Replacing the power cable : If the power cable of this device becomes damaged, it has to be replaced by authorized dealers only

Should you have further questions , please contact your dealer.