OCTANE XL450 Home Theater Seating User Guide
- June 16, 2024
- Octane
Table of Contents
OCTANE XL450 Home Theater Seating
Product Information
Specifications
-
Models: XL450, XL500, XL550, XL600, XL650, XL700, XL750, XL800,
XL850, XL900 XS300, XS400, XS700, XS850, XS900, XS950 -
Website: https://manual-hub.com/
-
Contact: 888.627.6743
Product Usage Instructions
Unpack the box
Remove all packaging materials from the seat base and the seat back.
Attach the Seat Back
Slide the metal female receivers located on both sides of the seat back
onto the male steel mechanism posts attached to the seat base. With both
hands, firmly push down on the seat backs to lock them into place.
Apply Rubber Foot Pads
If placing the seats on a hard surface floor, apply the rubber pads to the
bottom of all plastic feet. This will prevent the seats from sliding. Failure
to follow this instruction can cause scratches to your floor. This step is not
necessary if the seats are placed on a carpeted floor.
Configure Your Layout
When placing the theater seats, please note that they do not connect to
each other. Each seat weighs over 100 pounds so when placed in position they
won’t move. The diagrams below will assist you in visualizing how to place the
seats based on your desired configuration. Please note there are several ways
each configuration can be put together so yours might vary slightly.
- 2 SEATS STRAIGHT
- 3 SEATS STRAIGHT
- 4 SEATS STRAIGHT
- 4 SEATS STRAIGHT WITH MIDDLE LOVESEAT
- 2 SEATS CURVED
- 3 SEATS CURVED
- 4 SEATS CURVED
- 4 SEATS CURVED WITH MIDDLE LOVESEAT
Power On (Power Recline Models Only)
Underneath each theater seat, towards the back, is an electrical cord with
a two-prong plug. Simply plug this into your wall outlet. If you have
purchased multiple theater seats or rows of seats, we recommend purchasing a
surge protector and plugging all the seats
per row into it. Please note that each cord is approximately 8 feet long. Only
2.8 amps of electricity are required for each seat.
How to Recline
- Models with Power Recline: Use the button controls on the side of the seat to recline to your desired position.
- Models with an Armless Power Recline Seat: Use the button controls on the adjacent seat with an arm to control the recline of both seats.
- Models with Manual Recline: Pull the lever located on the side of the seat and lean back until it locks into place.
LED Cup Holders & Baserail
Remove any ties holding the extra cable to the frame. You can then attach
the LED cable to the extra connector located on an adjacent seat that contains
an arm. The adjacent seat will then control both the lower LED lights for the
two seats.
Accessory Dock
The Accessory Dock was designed to enhance your theater seating experience.
It is constructed of 100% aluminum and situated on each arm in front of the
cup holders. It fits a host of accessories (all sold separately), including a
swivel tray table, wine glass holder, iPad & tablet holder, phone holder, LED
flex light, and many other items. You simply slide the accessory into the
Accessory Dock and enjoy. Simply remove the accessory when not in use. Please
note that not all models offer this feature.
Models
XL450, XL500, XL550, XL600, XL650, XL700, XL750, XL800, XL850, XL900 XS300,
XS400, XS700, XS850, XS900, XS950
WWW.OCTANESEATING.COM
GET READY
Please read all instructions carefully before starting the assembly. It is recommended to use two adults throughout the process.
Prep the Furniture
Remove all packaging materials from the seat base and the seat back. Please
read all instructions carefully before starting the assembly. It is
recommended to use two adults throughout the process.
Attach the Seat Back
Slide the metal female receivers located on both sides of the seat back onto
the male steel mechanism posts attached to the seat base. With both hands,
firmly push down on the seat backs to lock them into place.
Apply Rubber Foot Pads
Locate the small bag of round rubber foot pads sent with your theater seats.
If placing the seats on a hard surface floor, apply the rubber pads to the
bottom of all plastic feet. This will prevent the seats from sliding. Failure
to follow this instruction can cause scratches to your floor. This step is not
necessary if the seats are placed on a carpeted floor.
Configure Your Layout
When placing the theater seats, please note that they do not connect to each
other. Each seat weighs over 100 pounds so when placed in position they won’t
move. The diagrams below will assist you in visualizing how to place the seats
based on your desired configuration. Please note there are several ways each
configuration can be put together so yours might vary slightly.
Power On (Power Recline Models Only)
Underneath each theater seat, towards the back, is an electrical cord with a
two-prong plug. Simply plug this into your wall outlet.If you have purchased
multiple theater seats or rows of seats, we recommend purchasing a surge
protector, plugging all the seats per row into it. Please note that each cord
is approximately 8 feet long.
Only 2.8 amps of electricity are required for each seat.
HOW TO RECLINE
Models with Power Recline
- Plug the theater seats into a power source, such as a wall outlet or surge protector.
- Locate the two buttons to recline the seat up and down. Depending on the model purchased this will be situated on either the rim of the cup holder or on the inside arm.
- Press and hold the button to recline the seat until you have reached your desired position, then release.
- To bring the chair back up follow the same procedure as above, but with the other button.
Models with an Armless Power Recline Seat
The recline buttons to recline the seat up and down will be located on the
side of the frame below the seat cushion.
Models with Manual Recline
Locate the recline lever. Depending on the model purchased this will be situated on either the inside arm as a latch handle or on the inside frame slightly below the seat cushion as a parachute cord.
- Using your fingers, release the lever by pulling it out away from the chair. This will release the footrest.
- To recline the seat even further, use the weight of your back on the backrest and also place the sole of your foot on the footrest and push outwards until your desired reclined position has been achieved.
- To bring the chair back up, use the weight of your legs and back to push the chair upright and close the foot ottoman
LED CUP HOLDERS & BASERAIL
- Plug the theater seats into a power source, such as a wall outlet or surge protector.
- Locate the button to turn the lights on and off. Depending on the model purchased this will be situated on either the rim of the cup holder or on the inside arm.
- Press the button once and the lights will come on.
- Press the button again to turn them off.
- If you have an armless seat in your configuration, you will need to locate the cord to the base rail LED Light Strip and remove any ties holding the extra cable to the frame. You can then attach the LED cable to the extra connector located on an adjacent seat that contains an arm. The adjacent seat will then control both the lower LED lights for the two seats.
ACCESSORY DOCK
The Accessory Dock was designed to enhance your theater seating experience. It is constructed of 100% aluminum and situated on each arm in front of the cup holders. It fits a host of accessories (all sold separately), including a swivel tray table, wine glass holder, iPad & tablet holder, phone holder, LED flex light, and many other items. You simply slide the accessory into the Accessory Dock and enjoy. Simply remove the accessory when not in use.
FAQ
Q: Do I need to assemble the seat base and seat back?
A: No, the seat base and seat back come pre-assembled. You only need to attach the seat back to the seat base.
Q: Can the seats be connected to each other?
A: No, the seats do not connect to each other. Each seat weighs over 100 pounds and will stay in place when positioned.
Q: How long are the electrical cords?
A: Each cord is approximately 8 feet long.
Q: What power is required for each seat?
A: Only 2.8 amps of electricity are required for each seat.
Q: Are all models equipped with LED cup holders and base rail?
A: No, not all models offer this feature.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>