XS850 Black Leather Match Recliner By Octane Seating User Guide
- June 16, 2024
- OCTANE SEATING
Table of Contents
XS850 Black Leather Match Recliner By Octane Seating
Product Information
Specifications
- Models: XL450, XL500, XL550, XL600, XL650, XL700, XL750, XL800, XL850, XL900 XS300, XS400, XS700, XS850, XS900, XS950
- Website: https://manual-hub.com/.
- Contact: 888.627.6743
Product Usage Instructions
-
Unpack the Box
Remove all packaging materials from the seat base and the seat back. -
Attach the Seat Back
Slide the metal female receivers located on both sides of the seat back onto the male steel mechanism posts attached to the seat base. With both hands, firmly push down on the seat backs to lock them into place. -
Apply Rubber Foot Pads
If placing the seats on a hard surface floor, apply the rubber pads to the bottom of all plastic feet. This will prevent the seats from sliding. Failure to follow this instruction can cause scratches to your floor. This step is not necessary if the seats are placed on a carpeted floor. -
Configure Your Layout
When placing the theatre seats, please note that they do not connect. Each seat weighs over 100 pounds so when placed in position they won’t move.
The diagrams below will assist you in visualizing how to place the seats based on your desired configuration. Please note there are several ways each configuration can be put together so yours might vary slightly.
- 2 SEATS STRAIGHT
- 3 SEATS STRAIGHT
- 4 SEATS STRAIGHT
- 4 SEATS STRAIGHT WITH MIDDLE LOVESEAT
- 2 SEATS CURVED
- 3 SEATS CURVED
- 4 SEATS CURVED
- 4 SEATS CURVED WITH MIDDLE LOVESEAT
Power On (Power Recline Models Only)
- Underneath each theatre seat, towards the back, is an electrical cord with a two-prong plug. Simply plug this into your wall outlet.
- If you have purchased multiple theatre seats or rows of seats, we recommend purchasing a surge protector and plugging all the seats per row into it. Please note that each cord is approximately 8 feet long.
- Only 2.8 amps of electricity are required for each seat.
How to Recline
-
Models with Power Recline
Use the buttons on the control panel to adjust the reclining position of the seat. -
Models with an Armless Power Recline Seat
Use the buttons on the control panel to adjust the reclining position of the seat. -
Models with Manual Recline
To recline the seat, push back on the seat back until it locks into place. -
LED Cup Holders & Baserail
Remove any ties holding the extra cable to the frame. You can then attach the LED cable to the extra connector located on an adjacent seat that contains an arm. The adjacent seat will then control both the lower LED lights for the two seats.
Accessory Dock
The Accessory Dock was designed to enhance your theatre seating experience. It
is constructed of 100% aluminium and situated on each arm in front of the cup
holders. It fits a host of accessories (all sold separately), including a
swivel tray table, wine glass holder, iPad & tablet holder, phone holder, LED
flex light, and many other items. You simply slide the accessory into the
Accessory Dock and enjoy. Simply remove the accessory when not in use.
Please note that not all models offer this feature.
FAQ
-
Q: Can I place the seats on a hard surface floor?
A: Yes, you can place the seats on a hard surface floor. However, make sure to apply the rubber foot pads to prevent sliding and scratches to your floor. -
Q: How much electricity is required for each seat?
A: Only 2.8 amps of electricity are required for each seat. -
Q: Can I connect multiple theatre seats?
A: No, the theatre seats do not connect.
Unpack the box
GET READY
Please read all instructions carefully before starting the assembly. It is recommended to use two adults throughout the process.
-
Prep the Furniture
Remove all packaging materials from the seat base and the seat back. -
Attach the Seat Back
Slide the metal female receivers located on both sides of the seat back onto the male steel mechanism posts attached to the seat base. With both hands, firmly push down on the seat backs to lock them into place.
-
Apply Rubber Foot Pads
Locate the small bag of round rubber foot pads sent with your theatre seats. If placing the seats on a hard surface floor, apply the rubber pads to the bottom of all plastic feet. This will prevent the seats from sliding. Failure to follow this instruction can cause scratches to your floor. This step is not necessary if the seats are placed on a carpeted floor.
-
Configure Your Layout
- When placing the theatre seats, please note that they do not connect. Each seat weighs over 100 pounds so when placed in position they won’t move.
- The diagrams below will assist you in visualizing how to place the seats based on your desired configuration. Please note there are several ways each configuration can be put together so yours might vary slightly.
-
Power On (Power Recline Models Only)
Underneath each theatre seat, towards the back, is an electrical cord with a two-prong plug. Simply plug this into your wall outlet.
If you have purchased multiple theatre seats or rows of seats, we recommend purchasing a surge protector and plugging all the seats per row into it. Please note that each cord is approximately 8 feet long.
- Only 2.8 amps of electricity are required for each seat.
HOW TO RECLINE
Models with Power Recline
- Plug the theatre seats into a power source, such as a wall outlet or surge protector.
- Locate the two buttons to recline the seat up and down. Depending on the model purchased this will be situated on either the rim of the cup holder or on the inside arm.
- Press and hold the button to recline the seat until you have reached your desired position, then release.
- To bring the chair back up follow the same procedure as above, but with the other button.
Models with an Armless Power Recline Seat
The recline buttons to recline the seat up and down will be located on the
side of the frame below the seat cushion.
Models with Manual Recline
- Locate the recline lever. Depending on the model purchased this will be situated on either the inside arm as a latch handle or on the inside frame slightly below the seat cushion as a parachute cord.
- Using your fingers, release the lever by pulling it out away from the chair. This will release the footrest.
- To recline the seat even further, use the weight of your back on the backrest and also place the sole of your foot on the footrest and push outwards until your desired reclined position has been achieved.
- To bring the chair back up, use the weight of your legs and back to push the chair upright and close the foot ottoman until it locks into place.
LED CUP HOLDERS & BASERAIL
- Plug the theatre seats into a power source, such as a wall outlet or surge protector.
- Locate the button to turn the lights on and off. Depending on the model purchased this will be situated on either the rim of the cup holder or on the inside arm.
- Press the button once and the lights will come on.
- Press the button again to turn them off.
- If you have an armless seat in your configuration, you will need to locate the cord to the base rail LED Light Strip and remove any ties holding the extra cable to the frame. You can then attach the LED cable to the extra connector located on an adjacent seat that contains an arm. The adjacent seat will then control both the lower LED lights for the two seats.
ACCESSORY DOCK
The Accessory Dock was designed to enhance your theatre seating experience. It is constructed of 100% aluminium and situated on each arm in front of the cup holders. It fits a host of accessories (all sold separately), including a swivel tray table, wine glass holder, iPad & tablet holder, phone holder, LED flex light, and many other items. You simply slide the accessory into the Accessory Dock and enjoy. Simply remove the accessory when not in use.
Please note that not all models offer this feature.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>