ONE FOR ALL Access 5 Universal Remote Control User Manual
- June 16, 2024
- ONE FOR ALL
Table of Contents
- INTRODUCTION
- FEATURES AND FUNCTIONS
- INSTALLING BATTERIES
- SETTING UP YOUR COMPONENTS
- SETTING UP TV/VCR COMBO CONTROL
- SEARCHING FOR YOUR CODE
- CHECKING THE CODES
- RE-ASSIGNING DEVICE KEYS
- CHANGING VOLUME LOCK
- TROUBLESHOOTING
- MANUFACTURER’S CODES
- LIFETIME WARRANTY
- ADDITIONAL INFORMATION
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ACCESS 5
UNIVERSAL REMOTE CONTROL
USER’S-GUIDE
INTRODUCTION
The One For All Access 5 Universal
Remote Control is designed to operate five home entertainment devices,
including TV, video, and audio components.
The remote control requires two fresh AAA alkaline batteries (not included)
and easy programming to control your devices.
For best results, please read and perform all instructions listed here. Also,
keep these instructions for future reference.
FEATURES AND FUNCTIONS
Use the Key Charts to learn how to use the universal functions of the One For
All Access 5 Universal Remote Control.
Key Charts
| Use SET for all programming sequences.
---|---
| The LED (red light) blinks to show that the remote control is working and is
sending signals.
| Press POWER once to turn on or off the selected device.
| Press VCR/DVD, AUX, RCR/AMP, CBL/SAT TV once to select home entertain device
to cont..
| Use the keypad “3 ~’d) to directly select channels (for example, O9or31)
| Press PREV once to recall the last-viewed channel and to page back one
screen on the main menu.
| Press ENTER once after entering channel numbers on some TVs. main menu.
| Press SLEEP to activate your device’s sleep timer (not available for all
devices).
| Press MUTE once to turn sound off or on.
| Press SHIFT and use the Up/Down/Left/Right cursor keys to move the cursor in
the program guide and menu screens.
Press SHIFT and MUTE to select a menu item.
| Use VOL+ (or VOL-) to raise (or lower) the “Sounc ‘volume;
| Use CH ▲ (or CH ▼) to select the next higher (or lower) channel.
| When controlling DVD/CD player, use SKIP FORWARD (or SKIP REV) to skip to
the next (or previous) DVD chapter/CD track.
| Press MENU once to display your selected devices main menu,
| Use EXIT to exit from your selected device’s Menu or guide,
| Use GUIDE to display your selected device’s
| Use INFO to display the current channel and program information.
| Use the transport keys to control your VCR, CD or DVD player, or VOD.
To record a program, press the Record key (REC)twice.
| Use TV/VID to switch the TV’s input to view TV or video programs.
INSTALLING BATTERIES
-
On the remote control’s back, push the tab and lift off the battery cover.
-
Obtain two (2) new AAA alkaline batteries. Match the + and – marks on the batteries to the + and – marks in the battery case, then insert the new batteries.
-
Press the battery cover back into place. The tab should click when the cover is locked.
-
Test the unit by pressing POWER and any mode key (e.g., TV). If batteries are inserted correctly, the LED will blink once.
NOTE: When batteries need replacement, the remote control will stop operating. Remove the old batteries and insert new ones within 30 minutes to ensure all of your programming information is restored.
SETTING UP YOUR COMPONENTS
The One For All Access 5 remote control is preprogrammed at the factory to
operate an RCA TV and VCR; a Motorola- (GI) cable box, a Pioneer audio tuner,
and a RadioShack X-10 home automation unit. To control devices other than the
default brands, perform the following steps; otherwise skip this section:
NOTE: For TV/VCR Combo control, see the next section.
-
Turn on a device (e.g., VCR) and, if applicable, insert media, (e.g., cassette or disc).
NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step -
On the remote control, press a device key once (i.e., VCR/DVD, AUX, RCR/AMP, CBL/SAT, or TV). Press and hold SET until the LED blinks twice, then release SET.
-
Use the Manufacturer’s Codes to locate the the type of device and brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice.
NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again. -
Aim the remote control at the device and press POWER once. The device should turn off. If it does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code.
NOTE: If the device does not have a POWER key, press the (Play) key. -
Repeat steps 1 through 4 for each device you want to control.
SETTING UP TV/VCR COMBO CONTROL
Perform the following instructions to control a TV/VCR Combo:
-
Turn on the TV/VCR Combo and insert a video cassette.
NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step -
On the remote control, press VCR/DVD. Press and hold SET until the LED blinks twice, then release SET.
-
Use the Setup Codes For TV/VCR Combos (on the back side) to locate. the brand name and then enter the first four-digit code for your device.
If performed correctly, the LED will blink twice.
NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again. -
Aim the remote control at the device and press POWER once. It should turn off. If the device does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code.
NOTE: If the device does not have a POWER key, press the( Play) key..
SEARCHING FOR YOUR CODE
If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. For example, to search for a code for your TV:
-
On the remote control, press TV once.
-
Press and hold SET until the LED blinks twice, then release SET.
-
Enter 9-9-1.The LED will blink twice.
-
Aim the remote control at the TV and slowly alternate between pressing POWER and TV. Stop when the TV turns off.
NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first. -
To lock in the code, press and hold SET until the LED . blinks twice, then release SET.
-
To search for the codes of your other devices, repeat steps 1 through 5, but substitute the appropriate device key for the device you are searching for.
CHECKING THE CODES
If you have set up the remote control using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment:
For example, to find out which code is operating your TV:
-
On the remote control, press TV once.
-
Press and hold SET until the LED blinks twice, then release SET.
-
990 Enter9- 9-0. The LED will blink twice.
-
To view the code for the first digit, press 1-once. Wait 3 seconds, count the LED blinks (e.g., 3 blinks = 3) and write down the number.
NOTE: If a code digit is “0”, the LED will not blink. -
Repeat step 4 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit.
-
To check for codes of other devices, repeat steps 1 through 5, but substitute the appropriate device key for each device you are checking.
As before, write down each four-digit code.
RE-ASSIGNING DEVICE KEYS
The One For All Access 5 can be set to control a second TV, VCR, DVD player,
or zudio device.
For example, to control a TV, a cable box, and two VCRs, you will need to re-
assign the unused AUX key to operate the second VCR as follows:
-
On the remote control, press and hold SET until the LED blinks twice, then release SET.
-
992 Enter9- 9-2. The LED will blink twice.
-
Press VER once, then press AUX once.
-
The AUX key is now ready to be programmed for your second VCR. (See Setting Up Your Components).
To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence from the below chart for the most popular devices:
To Re-Assign Key
Sequence | Perform |
---|
VCR/DVD as
2nd TV key:| SET-9-9-2
– TV – VCR/DVD
VCR/DVD as 2nd
CBL/SAT key:| SET-9-9-2
-CBL/SAT – VCR/DVD
VCR/DVD as 2nd
RCR/AMP key:| SET-9-9-2
-RCR/AMP- VCR/DVD
VCR/DVD back to
VCR/DVD:| SET-9-9-2
-VCR/DVD – VCR/DVD
RCR/AMP as
2ndTV key:| SET-9-9-2
– TV-RCR/AMP
RCR/AMP as2nd
VCR/DVD key:| SET-9-9-2
– VCR/DVD-RCR/AMP
RCR/AMP as 2nd
CBL/SAT key:| SET-9-9-2
-CBL/SAT – RCR/AMP
RCR/AMP back to
RCR/AMP:| SET -9-9-2
-RCR/AMP-RCR/AMP
AUX as
2nd TV key:| SET-9-9-2
– TV – AUX
AUX as 2nd
VCR/DVD key:| SET-9-9-2
– VCR/DVD- AUX
AUX as 2nd
CBL/SAT key:| SET-9-9-2
-CBL/SAT – AUX
AUX back to AUX:| SET-9-9-2
– AUX- AUX
When a re-assignment is done, the LED will blink twice to confirm your choice.
At that time, you will need to program the remote control for the new device
(see Setting Up Your Components).
CHANGING VOLUME LOCK
The One For All Access 5 is set to control the volume of your TV in the TV, VCR/DVD, CBL/SAT, RCR/AMP, and AUX modes. If you want volume to be controlled by a mode other than TV (e.g., CBL/SAT), change the Volume Lock setting as follows:
To Change Volume Lock To Be Controlled By Another Mode:
- On the remote control, press and hold SET until the LED blinks twice, then release SET.
- 993 Enter 9 – 9-3 and then press any mode key once (except TV). The LED will blink twice.
- Now, whenever you press VOL+, VOL-, or MUTE, volume will be controlled by your mode choice.
Unlocking Volume Control:
NOTE: Perform these instructions when you want independent volume control
for each programmed device (e.g., TV volume control in TV mode, CBL/SAT volume
in CBL/SAT mode, etc.)
- On the remote control, press and hold SET until the LED blinks twice, then release SET.
- Enter 9-9-3 and then press VOL+. The LED will blink four times.
- Volume will again be controlled according to its default states.
TROUBLESHOOTING
PROBLEM: | LED does not blink when you press a key. |
---|---|
SOLUTION: | Replace batteries with two new AAA alkaline batteries. |
PROBLEM: | LED blinks when you press a key, but home entertainment device does |
not respond.
SOLUTION:| Make sure the remote control is aimed at your home entertainment
device and is not farther than 15 feet away.
PROBLEM:| The unit does not control ‘home entertainment devices or commands
are not working properly.
SOLUTION:| Try all listed codes for the device brands being set up. Make sure
they can be operated with an infrared remote control.
PROBLEM:| TV/VCR combo does not respond properly.
SOLUTION:| Use the VCR codes for your brand. Some combo units may require both
a
PROBLEM:| TV code and a VCR code for full operation.
SOLUTION:| Changing channels does not work properly.
PROBLEM:| If original remote control required pressing ENTER to change
channels, press
SOLUTION:| ENTER on the remote control after entering the channel number.
PROBLEM:| Tried “Search Method” and still could not find a working code.
SOLUTION:| Clear the device key as follows: Press and hold SET until the LED
blinks twice, then release. Next enter 9 – 9 – 2. Then
press the device key to be cleared twice. Now repeat the “Search Method.”
PROBLEM:| Remote control does not turn on Sony or Sharp TV/VCR Combo
SOLUTION:| For power on, these products require programming TV codes, For
Sony, use TV code 0000 and VCR code 0032. For Sharp, use
TV code 0093 and VCR code 0048.
PROBLEM:| CH A and CHW do not work for your RCA TV.
SOLUTION:| Due to RCA design (1983- 1987), only the original remote control
will operate these functions.
PROBLEM:| If the above does not work.
SOLUTION:| Please contact us in any of the following ways:
• Please visit : www.oneforall.com
• If the above website is not able to provide you with the information you
need, please email us at ofasupport@ueic.com
• Customer Support: 330-405-8612
MANUFACTURER’S CODES
Setup Codes For TVs
LIFETIME WARRANTY
One For ALL(“OFA”)warrants this product to be free from defects in materials
and workmanship, under normal use, throughout the period of the product’s
ownership by the original purchaser. This warranty does not (over damage or
failures caused by products or services not supplied by OFA, or which result
from accident, misuses, abuse, neglect. mishandling, misapplication, faulty
installation, set -up adjustment, improper maintenance, alteration.
maladjustment of consumer controls, modifications, commercial use, or that is
attributable to acts of God.
There are no express warranties except as listed above. OFA SHALL NOT BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT OR ARISING OUT OF ANY BREACH OF WARRANTY, ALL EXPRESS AND IMPLIED
WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR-PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE. Some
states do not allow the exclusion or limitation of incidental or consequential
damagers, or limitations on how long an implied warranty lasts, so the above
exclusions or limitations may not apply to you. This warranty gives you
specific legal rights and you may also have other rights which vary from state
to state.
To obtain warranty service for a defective product, please return the product,
preferably in the original carton, along with your purchase receipt, to the
store of original purchase for the first 90 days. A note detailing the
complaint would be helpful. The store, at its option, will replace or repair
this product if found to be defective.
If the unit has been purchased more than 90 days ago, pls return it to Impact
Distribution Services, 6262 Patterson Pass Road, Suite C, Livermore, CA 94550
together with the original receipt and $3.95 to cover postage and handling. It
will be repaired or replaced at the manufacturer’s option. The manufacturer
reserves the right to substitute a currently manufactured model with equal or
superior features.
ADDITIONAL INFORMATION
ONE FOR ALL'”is the registered trademark of Universal Electronics Inc.
Computime International Ltd. is the Licensee of the ONE FORALL'”brand for USA
and Canada.
Copyright 2001 by Universal Electronics Inc. No part of this publication may
be reproduced, transmitted, transcribed, stored in any retrieval system, or
translated to any language, in any form or by any means, electronic,
mechanical, magnetic, optical, manual, or otherwise, without the prior written
permission of Universal Electronics Inc.
One For All@ Access5 is compatibile for use in North America excluding Mexico.
URC-5705/5741
06/02
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>