ONE FOR ALL URC-8350 Universal Remote Control Instruction Manual

: June 16, 2024
: ONE FOR ALL

Table of Contents

Installing the Batteries
The Keypad
Setting up the URC 8350
Extra Features
Troubleshooting
Using the Energy Saver Key
How to change the number of your HC-8000
Lighting Control
Specification HC-8000
Customer Service
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ONE FOR ALL URC-8350 Universal Remote Control

Installing the Batteries

Your URC-8350 requires 2 new “AAA/LR03” alkaline batteries.

Remove the battery cover from the back of your URC-8350 by pressing down on the tab.
Match the batteries to the + and – marks inside the battery case, then insert the batteries.
Press the battery cover back into place.

Important notes:

Do not use rechargeable batteries.
Upon changing the batteries, your set-up codes and advanced programming will be retained.

The Keypad

Device Keys
The TV, DVD, AUDIO and STB keys select the home entertainment device to be controlled. The device keys can also be programmed with a Macro (see page 9).
LED (red light)
During operation of the URC-8350 the LED will light up to indicate that it is sending out infrared.
POWER
The POWER key operates the same function it did on your original remote control.
Number Keys (0 – 9 and letters, -/- -, AV)
The Number keys (0-9, -/- -, AV) provide functions just like your original remote, such as direct access to channel selection. If your original remote uses one/two digit input switching (-/- – symbol), this function can be obtained by pressing the -/- – key. If your original remote has a 10 key, this function can also be found under the -/- – key. If your original remote has a 20 key, this function can also be found under the AV key. In AUDIO mode the Number keys may provide source (input) selection.
AV key
In TV mode you will obtain the AV / Input function. In AUDIO mode this key may give an Input/Source function. In DVD mode this key may give a TV/DVD function.
Replay key
Press Replay to command your PVR to instantly replay the last 7 seconds of a program you are watching.
Energy Saver Key
This key will allow you to switch to energy saving mode. Please go to page
12 – 13 for more information.
Advance key
Press Advance to return to Advance/Quick Skip.
Guide
In TV and/or STB mode you will obtain the “Guide” function, if available on your original remote. In AUDIO mode you will obtain the DSP mode function.
MENU Key
The MENU key controls the same function as it did on your original remote.
EXIT
In TV and/or STB mode you will obtain the “Menu Exit” function, if available on your original remote.
Info
In TV and/or STB mode you may obtain the ‘Display”, “OSD” or “Info” function, if available on your original remote.
Directional Keys
If available on your original remote, these keys will allow you to navigate through the menu mode of your device.
OK
The OK key will confirm your choice in menu operation and programming mode.
Volume +/- Keys
These keys operate in the same way as the keys on your original remote. If no volume-function is present on your device, you will obtain the volume of the device that is programmed on the AUDIO key.
Channel +/- Keys
These keys operate in the same way as the keys on your original remote. In PC mode they will allow you to skip up or down through pages.
MUTE Key
The Mute key operates the same function it did on your original remote control. If no mute-function is present on your device, you will obtain the mute function of the device that is programmed on the AUDIO key.
LAST Key
This key will provide you the “LAST” (or Recall or Previous Program) function (if available on your original remote).
Red, Green Yellow and Blue
After pressing the TV key and accessing the text mode, the keys marked red, green, yellow and blue, allow you to access the Fastest functions of your television. If on your original remote control these keys are used for Menu navigation, the URC-8350 Fastext keys may operate in the same way. These keys are also available in the STB mode.
Transport keys
These keys operate the transport functions (PLAY, FF, REW etc.) of your device.
Teletext Keys
After pressing the TV key, the transport keys (REW, PLAY, PAUSE, FF) are used to operate the main Teletext functions. The symbols below the keys are for Teletext.
The text keys are used to access the Teletext functions of your television. Of course, your television must have Teletext capability.

TEXT ON: Puts the television in the Teletext mode.
TEXT OFF: Switches the television back to regular viewing mode.
On some televisions, this may be done by pressing the TEXT ON key several times.
EXPAND: Shows the top half of the Teletext page in larger letters.
By pressing again, you can see the bottom half of the Teletext page enlarged. To return to regular Teletext viewing, press the EXPAND key again, or press the TEXT ON key, depending on your television.
HOLD/STOP: Stops changing pages.
MIX: Shows teletext and regular television simultaneously.
You may also use this key for subtitling. On some televisions this function is accessed by pressing the text key twice.
16:9: This key provides you the (16:9) wide screen view function (if available on your original remote).

Setting up the URC 8350

How to set up the URC 8350 to control your Devices

Example: To set up the URC-8350 for your Television (on the TV key):

Find the code for your device in the Code list. Codes are listed by device type and brand name. The most popular code is listed first. Make sure your device is switched on (not on standby).
Press and release the TV key on the URC-8350.
Press and hold down REWIND + FAST-FORWARD simultaneously until the URC-8350’s LED (red light) blinks twice
(the LED will blink once and then twice).
Enter your five-digit device code using the number keys.
The LED will blink twice.
Now, aim the URC-8350 at your device and press POWER.
If your device switches off, the URC-8350 is ready to operate your device.
Turn your device back on and try all the remote’s functions to ensure they are working properly. If the functions do not work properly, repeat steps 1-5 using another code listed under your brand.
If your device does not respond, follow steps 1 to 5 with each code listed for your brand. If none of the codes listed for your brand operate your device, or if your brand is not listed at all, try the Search Method described on page 6.
- Most TV’s do not switch on pressing the POWER key. Please try pressing a “number” key or the “TV-text off” key to switch your TV back on.
- If your device’s original remote control does not have a POWER key, press PLAY instead of POWER when setting up your device.
- Some codes are quite similar. If your device does not respond or is not functioning properly with one of the codes, try another code listed under your brand.
- To set up your other devices, follow the same instructions above, only press the appropriate device key during step 2.
- Remember to press the corresponding device key before operating your device.

The TV, STB and AUDIO keys are not mode specific. So it is possible to set up a second Television on the STB key (If you do not have a Set-Top-Box) or a second satellite receiver on the AUDIO key for example.

Search Method
–> If your device does not respond to the URC-8350 after you have tried all the codes listed for your brand.
–> If your brand is not listed at all.
The Search Method allows you to scan through all the codes contained in the memory of the URC-8350.

Example: To search for your TV code (on the TV key):

Switch ON your television (not on standby) and aim your URC-8350 at your TV.
Press and release the TV key.
Press and hold down REWIND + FAST-FORWARD simultaneously until the URC-8350’s LED (red light) blinks twice (the LED will blink once and then twice).
Press 9 9 1. The LED will blink twice.
Press 1 to scan through all TV codes. *
Next, press POWER.
Aim the URC-8350 at your Television. Now press UP over and over, until your Television turns off (every time you press the UP key the URC-8350 will send out a POWER signal from the next code contained in the memory).
You may have to press this key many times (up to 150 times) so please be patient. If you skip past a code, you can go to the previous code(s) by pressing the DOWN key.
Remember to keep pointing the URC-8350 at your Television while pressing this key.
As soon as your television turns off, press OK to store the code.

*() to scan through other device types:**

Press:	to scan through codes for:
Television / LCD / Plasma
DVD player/recorder or PVR
CD, Amplifier or Amp./Tuner or Miscellaneous
Set-Top-Box or Satellite Receiver or Cable Converter

Most TV’s do not switch on pressing the POWER key. Please try pressing a “number” key or the “TV-text off” key to switch your TV back on.
If you cannot control your Television properly, please continue the Search Method, you may be using the wrong Code.
To search for the code for another device follow the instructions above only press the appropriate device key instead of TV during step 2 and the appropriate number during step 5.

The Learning Feature
(How to copy functions from your original working remote onto the ONE FOR ALL URC 8350)

The URC-8350 comes with a complete library of pre-programmed codes. After you have set up the URC-8350 for your device, you may find that there are one or more keys that you had on your original remote, which do not have a place on the URC-8350 keypad.
As a convenience, the URC-8350 offers a special Learning feature that allows you to copy any function from your original remote control onto the keypad of the URC-8350.

Before you start:

Make sure your original remote control is working correctly.
Make sure neither your URC-8350, nor your original remote control is pointing at your device.

Example: To copy the “mono/stereo” function from your original TV remote onto the “LAST” key of your URC-8350.

Place both remote controls (the URC-8350 and your original) on a flat surface. Make sure the ends which you normally point at your device are facing each other. Keep the remotes at a distance of 2 to 5 cm.
Press and hold down REWIND + FAST-FORWARD simultaneously until the URC-8350’s LED (red light) blinks twice (the LED will blink once and then twice).
Press 9 7 5 (the LED will blink twice).
Press the device key (on the URC-8350 remote) to select the mode to which you want to copy the learned function (example: TV key).
Press the key (on the URC-8350 remote) where you want to place the learned function (example: LAST key).
The LED will flash rapidly.
Press and hold the key (on your original remote) that you want to copy until the LED on the URC-8350 blinks twice (example: “mono/stereo” key).
If you want to copy other functions within the same mode, simply repeat steps 5 and 6 pressing the next key you want to copy by learning. If you want to copy other functions to a different mode, then repeat from step 4 onwards and press the applicable mode key.
To exit the learning mode, press and hold OK until the LED blinks twice.
Learning is mode specific. To access your learned function, press the appropriate device key first.
- The URC-8350 can learn approximately 25 – 40 functions (depending on the function to be learned). Memory full will be indicated by two long blinks.
- You can replace a learned function by placing another learned function on top.
- Upon changing the batteries, your learned functions will be retained.

Extra Features

Volume Punch Through

If no volume-function is present on your device, you will obtain the volume of the device that is programmed on the AUDIO key.
Volume Punch Through allows you to use the volume from another mode without having to select this. E.g. controlling your TV volume while being in STB mode.

To punch through to TV volume while in the STB or AUDIO mode:

Press and hold down REWIND + FAST-FORWARD simultaneously until the URC-8350’s LED (red light) blinks twice (the LED will blink once and then twice).
Press 9 9 3. The red light will blink twice.
Then press the TV key and the red light will blink twice.

Result: being in STB mode, you will be able to control VOL+/- or MUTE functions of your STB (provided it has volume control).

To cancel the „Volume Punch Through“ for all modes:

Press and hold down REWIND + FAST-FORWARD simultaneously until the URC-8350’s LED (red light) blinks twice (the LED will blink once and then twice).
Press 9 9 3. The red light will blink twice.
Press the Volume (+) key and the red light will blink four times.

Result: all devices will operate their own volume-function again (provided it is present).

Macros (Sequence of commands within a certain mode)

Within a certain device mode you can program your URC-8350 to issue a sequence of commands at the press of one key.

Example: To program a macro on the LAST key to go to “AV” mode (in TV mode) then to channel 801 of your Set-Top-Box.

Press and release TV key to select the mode where you want to execute the macro.
Press and hold down REWIND + FAST-FORWARD simultaneously until the URC-8350’s LED (red light) blinks twice (the LED will blink once and then twice).
Press 9 9 5. The LED will blink twice.
Then press the LAST key (to which the Macro will be assigned).
Next press TV then AV then STB then 8 0 1 to select the desired channel on your Set-Top-Box.
To store the Macro, press and hold the OK key until the LED will blink twice.

Result: In TV mode, when you press and hold the LAST key the URC-8350 will send commands to go in “AV” mode then switch to STB mode and go to channel 801 of your Set-Top-Box.

If you need to build in some delay into the sequence please use the corresponding device-mode key (e.g. STB key in example above) to do so. You may press this key several times to build in more delay.
Each MACRO can consist of a maximum of 32 key strokes.
Make sure that you program a Macro on a spare key, as the Macro will overwrite the pre-programmed function in the mode where the Macro is programmed.
If you had to hold down a key for a few seconds on the original remote control to get a function, this function may not work in a macro on your URC-8350 remote.

Erasing the Macro

Example: To erase the Macro from the LAST key in STB mode, press:

Press and release the device key (e.g. STB key) to select the mode where the macro is stored.
Press and hold down REWIND + FAST-FORWARD simultaneously until the URC-8350’s LED (red light) blinks twice (the LED will blink once and then twice).
Press 9 9 5. The LED will blink twice.
Press the LAST key (from which you want to erase the macro).
To clear the Macro, press and hold the OK key until the LED will blink twice.

Code Upgrade Technology

Your URC-8350 Remote contains a unique feature, which allows new codes to be added simply by holding it to your telephone. In a matter of seconds, our magnetic coupling technology quickly and reliably transfers information to the URC-8350 Remote without complex plugs, adapters or attachments.This means, as you buy new products in the future, the URC-8350 Remote will never become obsolete.

Internet download
(Upgrade your URC-8350 Remote…via your PC)

Visit our website “www.oneforall.com”.
Select your region.
Select “Support”.
Select “Download center”.
Select “Universal Remote Controls”.
Select the ONE FOR ALL remote you want to upgrade: URC-8350.
Select “DWNLD” Now you have entered our special Online Download section. From this point just follow the instructions on the screen for easy upgrade of your remote.

Phone upgrade
(Upgrade your URC-8350 remote…via your phone). Alternatively ring our consumer help-line and one of our customer service representatives will assist you through the entire process of upgrading your URC-8350 Remote. To ensure the process goes smoothly, here are a few steps to follow:

Write down the brand name(s) and model number(s) of your device(s) (see the table provided on the Consumer Service page) before you call.
Ring our consumer help-line and explain which device(s) you would like to add to your URC-8350 Remote.
After our customer service agent records the brand name(s) and model number(s) of your device(s), he/she will lead you through the set up procedure and then will ask you to hold the URC-8350 Remote to the speaker portion of your telephone (see diagram below). In doing this, the information needed for your device is transferred through the telephone into your URC-8350 Remote in a matter of seconds.
IMPORTANT: cordless telephones, speaker telephones and mobile telephones are not recommended.
After your URC-8350 Remote has been upgraded by telephone, stay on the line. Our customer service agent will ensure that your URC-8350 Remote is working properly with your device(s) and will answer any other questions you may have.

Troubleshooting

Problem:	Solution:
Your brand is not listed in the code section?	Try the search method on page

The URC-8350 does not operate your device(s)?| A) Try all the codes listed for your brand. B) Try the search method on page 6.
The URC-8350 is not performing commands properly?| You may be using the wrong code. Try repeating the Direct Set-Up using another code listed under your brand or start the search method over again to locate the proper code.
Problems changing channels?| Enter the programme number exactly as you would on your original remote.
The URC-8350 does not respond after pressing a key?| Make sure you are using new batteries and are aiming the URC-8350 at your device.
The LED does not blink when you press a key?| Replace batteries with 2 fresh, new “AAA/LR03” alkaline batteries.

Using the Energy Saver Key

In combination with the included On/Off Power Plug (HC-8000), your One For All URC 8350 can be used as a convenient remote control for switching your Audio Video devices completely off, saving more energy than the standby mode. The optimal way to do this is to plug all of your devices into one power strip or multi-way extension lead (see illustration below)and then plug that into the One For All Power Plug.

You can then shut the Power to all devices using the URC 8350. To do this first enter the Energy Saving Mode by pressing the Energy Saver Key. Now you need to select which Power Plug you want to control. Each Plug has a number and the one that shipped with this kit defaults to number 1, so press the number. You can now turn the Power completely off by pressing the following keys:

Power ON – Press Channel Up (+)
Power OFF – Press Channel Down (-)

The remote will remember the last plug you controlled, so if you switch from Energy Saving Mode l to TV mode and then back again you will be able to control the last plug control switch you accessed without needing select it by pressing 1.

How to change the number of your HC-8000

It is possible to change the number you use to select the HC8000 Power Plug. This is useful if you have purchased a second Power Plug (available from One For All), or if you already have a Power Plug operating as number 1.
To assign a number to the plug, follow these steps:

Plug your device (or extension lead) the HC-8000 into the wall If you are setting up a device with an in-line switch (such as a lamp), make sure the switch is set to On
Press the Energy Saver key on your ONE FOR ALL URC-8350 so that it is in Energy Saving Mode.
Press the number you wish to assign to the Power Plug Switch (HC-8000). If this is your first Plug, number 1 is recommended, number 2 for the second etc. The IR Indicator (LED) at the top of the URC-8350 should blink twice.
Press and hold the button on the Power Plug (HC-8000) until the red light begins to blink.
Press the Channel Up (+) key. The red light on the Light Power Plug (HC-8000) should stop flashing.
The remote should now operate the Power Plug (HC-8000).
To test it, check if the Channel Up (+) and (-) keys work to switch your light ON and OFF respectively,.
If you require more than 10 plugs to control, you can also use the Red, Green, Yellow and Blue keys on your remote to control 11-14. Simply assign these keys to the Power Plugs HC-8000) as you would do a number.
If you experience interference, it is possible to change the code of the Energy Saver Mode on your remote to avoid this. The default code is 41000, but it is possible to change the code to 41001, 41002 etc up to 41015. To change the code, set the Light Mode up as you would do a normal device (see page 5), using codes 41000 – 41015.
If you should wish to reset your Power Plug HC-8000 to factory defaults so you can assign it a new number, hold down the button on the Light Control Switch until the red light starts to blink, release the button and then hold it down again until the red light goes out.

Lighting Control

If you should wish to remotely control lamps and lighting as well as Energy Saving, you can also use the Energy Saver remote to control the separately available One For All Light Accessories.

Specification HC-8000

Voltage and Load: 230V~
Degree of Protection: IP 20
Radio Frequency: 433.92MHz
RF Range : Typically 30m in open area.
Max power for HC-8000 : 1000 Watt

Customer Service

In the UK
E-mail : ofahelp@uebv.com ()
Fax : +31 53 432 9816
Tel. : 0901-5510010 (£ 0,50 per minute)
In Australia
E-mail : ofahelp@uebv.com ()
Fax : 03 9672 2479
Tel. : 1 300 888 298
In New Zealand
E-mail : ofahelp@uebv.com ()
Fax : (06) 878 2760
Tel. : 0508 ONE 4 ALL (663 4 255)
Slovakia
E-mail : ofa@dsi.sk
Fax : +421 55 611 8111
Tel. : +421 55 611 8131
Web. : www.dsi.sk
In Ireland
E-mail : ofahelp@uebv.com ()
Fax : +31 53 432 9816
Tel. : 016015986
In South Africa
E-mail : support@oneforall.co.za
Fax : 011 298 2302
Tel. : 0860 100551
Tel. : 011 4173000
Ukraine
E-mail : alexx@ckc.com.ua
Fax : +38 044 4890187
Tel. : +38 044 4890188
Web. : www.oneforall.com.ua
Croatia
E-mail : lucija@tehnocentar.hr
Fax : +385 1 48 16 807
Fax : +385 1 48 16 806
Web. : www.tehnocentar.hr
*) Just send a blank message, you’ll get auto-reply Logo