OVE DECORS OVE Calero Smart Toilet Seat Instruction Manual
- June 16, 2024
- OVE Decors
Table of Contents
CALERO
SMART TOILET SEAT
Measures: inch [millimeter]
INSTALLATION MANUAL
- Carefully read the instructions before starting the installation.
- This smart toilet seat should be installed by an experienced plumber.
If you are missing any part, please stop and contact us immediately at:
1-866-839-2888
OVE DECORS
1-866-839-2888
SAFETY NOTICE
ATTENTION!
BEFORE INSTALLING THE PRODUCT, YOU MUST READ AND UNDERSTAND CAREFULLY ALL
BELOW WARNINGS.
-
It is forbidden to disassemble toilet by yourself.
-
Please do not set this product in a wet place, because it is an electronic product. If set in the bathroom, please insure that there is proper air flow.
-
Please insure that the product is set more than 0.6 meter away from the bathtub.
-
Please make sure electric power is AC 120V. Ensure the electrical socket can bare a load of 1800W power (or else it can cause fire or electrical shock).
-
Please make sure the electrical source is well grounded.
-
Please do not put any water or detergent on the product or its electrical plug.
-
Do not touch the electrical plug with a wet hand (or else it can cause fire or electric shock).
-
Do not use the product if it has these following problems. When any of the following problems occur, turn off the electricity and close the water valve.
• Water leaking from the pipe or the main body.
• Crack or breakage
• Abnormal sound or smell of the product
• Smoke coming out from the product -
Keep any flame or flammable products away from the toilet.
-
Please do not step on the toilet seat, the seat cover, the main body, or put anything heavy on the product. Otherwise, the product may break and may cause injury or the product may break and may cause indoor flooding.
-
Please do not put your finger or anything else into the outlet of the drying blower.
-
Please do not touch or cover the drying blower outlet with clothes, or it may lead to burn injury or electric shock.
-
Please do not tightly bend or press the flexible supply hose, or it may lead to water leakage or it may decrease the water pressure.
-
Please clean the product with soft cleaning products.
-
Please do not use any harsh detergents to clean the product.
-
Please do not throw anything other than toilet paper into the toilet or it may lead to blockage and indoor flooding.
-
Please be careful to not let objects like a comb, toothbrush or other stuff fall into the toilet.
WARNINGS
Do not leave the toilet exposed to the sun. May cause yellowing or color fading.
Direct sunlight affects the good functioning of the remote.
|
To prevent against power surge damages, make sure the ground is working in the power socket.
---|---
Radio or transmitting devices may interfere with the toilet’s remote control functions
|
If you do not plan to use the toilet for a long time, close the inlet water valve and unplug the toilet.
If the power cut off during washing and the nozzle is still out: Do not push
it back manually, it will revert to its resting position once the power is
back ON.| Do not use DC current. Only AC 120V with load capacity over 1800W
are accepted.
If power cuts off during nozzle self-cleaning, the water will continue to flow
out. Manually close the inlet water valve of the toilet until power comes back
ON.|
Do not expose the toilet to freezing temperature. This will void the warranty and damage the piping.
Be careful not to spill water on the top of the toilet: Electronics are located under the plastic cover.
|
Do not lean on the cover.
PART LIST
|
Item
| Qty| #
---|---|---|---
A| Light Indicator Panel|
1
|
B
| Water Inlet| 1| —
C| Side Control Panel|
1
|
D
| Seat Water Tube| 1|
E| Water Filter|
1
|
F
| Inlet Valve (not supplied)| 1| —
G| Smart Seat (incl. electronics, cover, seat and lid)
Smart Seat (incl. cover, seat and lid)|
1
|
H
| Remote Receiver| 1|
I| Mounting plate release button| 1|
—
J
| Sensor| 1|
K| Nozzle|
1
|
L
| Dryer outlet| 1|
M| Remote|
1
|
N
| Tee joint| 1|
O| Mounting plate installation kit|
1
|
P
| Thicker seat rim bumper| 1|
Q| Check valve|
2
|
TOILET SEAT COMPATIBILITY
[1]
TO ENSURE THAT THE SMART SEAT IS COMPATIBLE WITH YOUR EXISTING TOILET BOWL:
A) Ensure that the distance between the centers of seat installation holes is in the range given by “A”.
B) Ensure that there is a clearance of at least “B” between the center of the seat installation holes and the front of the flush tank.
C) Ensure that the distance between the center of the seat installation holes and the front edge of the toilet bowl is in the range given by “C”.
D) Ensure that there is a clearance of at least “D” between the center of the toilet and the nearest wall on both sides.
TO YIELD A PERFECT FIT:
This smart seat is compatible with most elongated toilet bowls, as long as conditions A) to D) above are met. Nevertheless, to yield a nicely matching seat and bowl:
E) Measure the width of the toilet bowl at 3-1/8″ (80mm) from the front edge, and ensure that the width of the toilet bowl at this location is in the range “E”. This will ensure a perfect match between the shapes of the smart seat and the toilet bowl.
INSTALLATION INSTRUCTIONS
[1]
- Turn off the water inlet valve before starting the installation of the smart toilet seat.
- Only plug the smart seat to the electrical socket once the installation is completely finished.
| [2]
Loosely install the mounting plate with the plastic anchors, washers, and guides provided.
---|---
[3]
Before tightening the mounting plate, ensure that the distance between the back of plate and front edge of the toilet bowl is set to 19-11/16” (500mm). Then tightly secure the plate.
| [4]
Press the release button located on the left of the seat and push the seat onto the mounting plate. Once the seat is snuggly fitted onto the mounting plate, release the button and the seat will be locked in place.
[5]
If the provided seat rim bumpers do not touch your toilet bowl edge and there is a gap in between the two, change the pre-installed seat rim bumpers to the thicker ones provided (P).
[6]
Turn off the inlet valve, and unscrew the supply hose from the toilet.
| [7]
Screw the water supply hose to the Tee joint. Note that the filter is located in the reducer.
[8]
Screw the Tee joint to the toilet water inlet coupling.
| [9]
Connect the water tube to the smart seat. This is a pressure snap-in system, gently but firmly push the tube inside the hole.
FIRST TIME USE
[1] Open the water supply inlet valve.
[2] Plug the toilet in the power socket.
[3] The toilet’s blue light will start blinking.
The blinking light indicates that the wash tank is filling with water, a
sensor in the toilet will stop the filling process automatically after around
3 minutes when the tank is full of water.
After the wash tank is filled with water, the indicator light will stop
blinking.
[4] The toilet will turn ON automatically. Once the beeping sounds and the flashing light have stopped, the toilet is ready for use.
Notice:
- Warming up the toilet seat will take about 3 minutes.
- Warming up the bidet cleaning water will take about 3 min.
- Leave the power continuously ON to assure all functions are ready for anytime use.
CONTROLS DESCRIPTION
POWER/ECO:
Press 1 time, it will turn the toilet ON.
Press 2 times, it will activate the ECO MODE.
Press 3 times, it will turn the toilet OFF.
REAR BIDET/MOVE & MANUAL NOZZLE WASH:
Pressing this button will initiate the Static Rear Bidet Cleaning function.
Press it again to change to the Back-&-Forth Rear Bidet Cleaning function.
Pressing this button for 3 second until the toilet beeps. The toilet will
initiate the Back-&-Forth Rear Bidet Cleaning function. Press it again to
change to the Static Rear Bidet Cleaning function. After 20 seconds of use,
the Air Drying function will start automatically.
*The REAR BIDET refers the 1 water jet function of the nozzle.
LADY BIDET/MOVE:
Pressing this button will initiate the Static Lady Bidet Cleaning function.
Press it again to change to the Back-&-Forth Lady Bidet Cleaning function.
Pressing this button for 3 second until the toilet beeps. The toilet will
initiate the Back-&-Forth Lady Bidet Cleaning function. Press it again to
change to the Static Lady Bidet Cleaning function. After 20 seconds of use,
the Air Drying function will start automatically.
*The LADY BIDET refers the 4 water jets function of the nozzle.
DRYING/DEGERMING:
When user is NOT sitting on the toilet, pressing this button will turn off the
Ozone degerming function. Press it again will turn on this function.
When user sitting on the toilet, pressing this button will initiate the drying
function. Pressing again can change the air drying speed.
*The drying refers 2 dying speed.
STOP:
Pressing this button will stop any ongoing function.
POWER indicator:
The light will turn RED when the toilet is powered ON.
The light will turn off when the toilet is powered OFF.
ECO MODE indicator:
The light will turn YELLOW when the ECO MODE is active.
The light will turn off when the ECO MODE is not active.
WATER TEMP indicator:
Below are the different colors the light takes depending on the current
setting:
ROOM TEMP = Light OFF
LOW = GREEN
MEDIUM = ORANGE
HIGH = RED
SEAT TEMP indicator:
Below are the different colors the light takes depending on the current
setting:
ROOM TEMP = Light OFF
LOW = GREEN
MEDIUM = ORANGE
HIGH = RED
DEGERMING indicator:
The light will turn ON when the degerming function is active.
The light will turn OFF when the degerming function is not active.
BEEPING SOUNDS DIRECTIONS
1X BEEP = The toilet will give out one beeping sound every time it successfully receives a command from the Remote Control.
2x BEEP = The toilet will give out two beeping sounds every time it has successfully received a command, but cannot execute it. For example, if the Seat Sensor is not active and the user presses the REAR BIDET/MOVE button, the toilet will beep two times because the bidet function cannot be active if the seat sensor is not active.
BEEPING for Temperature levels:
While adjusting the temperature for the bidet water, the seat or the drying
air, the toilet will beep as follow to indicate which temperature has just
been set:
-ROOM TEMP = 1x long beep
-LOW = 1 x short beep
-MEDIUM = 2 x beep
-HIGH = 3 x beep
CONTROLS DESCRIPTION
REAR BIDET/MOVE:
Pressing this button will initiate the Static Rear Bidet Cleaning function.
Press it again to change to the Back-&-Forth Rear Bidet Cleaning function.
*The REAR BIDET refers the 1 water jet function of the nozzle.
LADY BIDET/MOVE:
Pressing this button will initiate the Static Lady Bidet Cleaning function.
Press it again to change to the Back-&-Forth Lady Bidet Cleaning function.
*The LADY BIDET refers the 4 water jets function of the nozzle.
DRYING:
Pressing this button will initiate the warm air drying.
Pressing again can change the air drying speed.
*The drying refers 2 dying speed.
AIR PUMP:
Pressing this button initiate the air pumps which will boost the water
pressure even more than the maximum attainable setting by the WATER PRESSURE
UP button.
NOZZLE FORWARD:
Pressing this button during the Static Bidet cleaning will move the nozzle
forward.
5 settings: 5 increments from back to front.
NOZZLE BACKWARD:
Pressing this button during the Static Bidet cleaning will move the nozzle
backward.
5 settings: 5 increments from front to back.
WATER PRESSURE DOWN:
Pressing this button during the Static or the Back-&-Forth Bidet cleaning will
decrease the water jet pressure.
8 settings: 8 increments from high to low.
WATER PRESSURE UP:
Pressing this button during the Static or the Back-&-Forth Bidet cleaning will
increase the water jet pressure.
8 settings: 8 increments from low to high.
WATER TEMPERATURE:
Pressing this button will cycle through the 4 possible temperatures settings
for the Bidet cleaning water jets.
4 settings: Room temp / Low / Medium / High
SEAT TEMPERATURE:
Pressing on this button will cycle through the 4 possible temperatures
settings for the seat heating.
4 settings: Room temp / Low / Medium / High
AIR TEMP:
Pressing this button will cycle through the 4 possible temperatures settings
for the air drying function.
4 settings: Room temp / Low / Medium / High
LIGHT:
Pressing this button will turn the toilet bowl’s light ON / OFF.
STOP:
Pressing this button will stop any ongoing function.
BEEPING SOUNDS DIRECTIONS
1X BEEP = The toilet will give out one beeping sound every time it successfully receives a command from the Remote Control.
2x BEEP = The toilet will give out two beeping sounds every time it has successfully received a command, but cannot execute it. For example, if the Seat Sensor is not active and the user presses the REAR BIDET/MOVE button, the toilet will beep two times because the bidet function cannot be active if the Seat Sensor is not active.
FEATURES
REAR BIDET CLEANING (1 WATER JET)
This function will only work if the user is sitting on the toilet. Press the
REAR BIDET/MOVE button for a rear bidet cleaning. Water will spray and clean
the user. Press the button again and the nozzle will move back & forth to
insure the cleanest result. You can use this key stoke to get the best
cleaning effect.
LADY BIDET CLEANING (4 JETS OF WATER)
This function will only work if the user is sitting on the toilet. Press the
LADY BIDET/MOVE button for a lady bidet cleaning. Water will spray and clean
the user. Press the button again and the nozzle will move back & forth to
insure the cleanest result. You can use this key stoke to get the best
cleaning effect.
If you are not seated on the toilet seat, the toilet seat sensors will prevent water from squirting out of the nozzle or warm air from flowing out of the dryer.
The nozzle washes itself before and after every use with the programmed automatic nozzle washing cycle.
The bidet function will automatically stop after 2 minutes of continuous use. To start it again press the button.
It will take about 10 seconds after pressing the REAR BIDET/MOVE or LADY BIDET/MOVE button before water starts to spray out of the nozzle. Please be patient.
AIR DRYING
This function will only work if the user is sitting on the toilet. Press the
DRYING button for air drying. The air will dry the user. Press the button
again and the air nozzle will move back & forth to insure driest result. You
can use this key stoke to get the best drying effect.
If you press the DRYING key while the toilet is flushing, you will need to wait about 10 seconds before the air starts to flow out of the dryer.
STOP
Pressing the stop button at any time will automatically stop any functions.
The toilet will keep spraying for 1-2 seconds after you stand up, so be sure to press the STOP button before standing up from the toilet seat, during the cleaning process.
LIGHT
Pressing the LIGHT button on the remote control board will turn ON the
toilet’s light, pressing the button again will turn it OFF.
INTELLIGENT FEATURES
ECO MODE
ECO MODE will cut down the electricity usage of your intelligent toilet during
times of none-usage. The cleaning water tank will start heating the water only
once the user is sitting on the toilet, whereas in normal mode, the cleaning
water is kept to your preferences for your instant enjoyment.
SOFT CLOSE DESIGN
The toilet seat and seat cover have a soundless soft close design that
prevents them from falling rapidly and denting or scratching the toilet.
ANTI-MICROBIAL SEAT
The toilet’s seat is coated with an eco-friendly antimicrobial polymer
preventing the growth of any microbe on the seat. Clean by design, for your
piece of mind.
AIR PUMP SUPERCHARGED
Press the AIR PUMP button on the remote control to activate a supercharged
water pressure pump.
This function will temporarily increase the water pressure for maximum
cleanness.
AUTOMATIC DEODORIZER
As soon as the user sits on the toilet, a fan sucks the air out of the toilet
bowl and through an advance odor fighting catalyzer. This prevents the bad
smells during the toilet’s usage, insuring a pleasant experience.
CLEANING THE FILTER
[1] Close the inlet valve, turn clockwise.
Do not take out the filter before closing the inlet valve.| [2] Unscrew
the reducer from the Tee joint and take out the filter.
---|---
[3] Clean the filter.
Use a tooth brush to clean the dirt on the filter.
Use a cloth to clean the dirt and deposits in the reducer.
Use water instead of detergent. Do not overexert the filter while cleaning, do
not damage the shape of the filter.
| [4] Install the filter back into the reducer.
Screw the reducer back onto the Tee joint.
Firmly tighten to avoid leakage.
[5] Open the inlet valve by turning counterclockwise.
Ensure there are no leaks.
LONG TERM STORAGE
In order to prevent from any damages that may be caused from frozen toilet water, please drain away the remaining water according to the following methods.
When leaving for a long time without using this toilet, please make sure to drain all the water from the toilet.
Preparation:
- Close water inlet valve.
- Turn off the power and unplug the power plug.
Uninstallation:
- Press in the mounting plate release button.
- Pull out the seat.
- Set the seat upright and unscrew the drain bolt, let the water drain entirely.
- Re-install the seat to the toilet.
SPECIFICATION SHEET
Item
|
Content
---|---
Electric Load| AC 120V / 1300W / 60HZ
Electric Cord| 1.2 m insulated power cord
Cleaning System
REAR Bidet| 1 jet
LADY Bidet| 4 jets
Water Temp| 4 settings: Room temp / LOW / MEDIUM / HIGH
Heater Capacity| AC 120V / 1200W / 60HZ
Cleaning Tank Capacity| 500mL
Overheating Safety| Temperature safety reset protector integrated. Toilet will
shutdown if temp. is out of specs.
Anti-Reflux| Anti-Reflux check valve integrated.
Drying System
Drying Air Temp| 4 settings: Room temp / LOW / MEDIUM / HIGH
Heater Capacity| AC 120V / 190W / 60HZ
Overheating Safety| Temperature Fuse
Heating Seat
Seat Temp| 4 settings: Room temp / LOW / MEDIUM / HIGH
Heater Capacity| AC 120V / 45W / 60HZ
Overheating Safety| By design
Limitations
Water Supply Pressure| Lowest water pressure is 0.1MPa (14.5 psi), highest
water pressure is 0.5MPa (72.5 psi)
Water Supply Temp| 15-35 C
Ambient Temp| 15-35 C
MAINTENANCE & CONSUMER RESPONSIBILITIES
- The DISTRIBUTOR does prohibits the use of harsh abrasive cleansers on any of its products. Harsh cleansers will damage the inner workings of the toilets.
- For daily maintenance, use a wet cloth and a soft liquid cleaner.
- Never use abrasives or cleaners containing acetone, chlorine or strong bleach, scrapers, metallic brushes, nor other objects or products which can graze or tarnish surfaces.
LIMITED 1 YEAR WARRANTY
The DISTRIBUTOR warranty is valid for a period of 1 year after purchased. Improper use of this product or any deviations to the general guidance given in the user manual will void the warranty. This non-transferable warranty applies only to the original purchaser and proof of purchase is required for all claims.
This warranty applies to the DISTRIBUTOR toilet installed for residential use
only.
The DISTRIBUTOR warrants that, when installed in accordance with the
Recognized Plumbing Industry Practice, the toilets are free of manufacturing
defects for a period of one (1) year from the date of purchase.
The DISTRIBUTOR will repair or replace the damaged product or parts only if they were installed and used in a proper way according this user manual.
Before accepting to repair or replace the product, the DISTRIBUTOR is entitled to send a representative to inspect the product. We will offer free of charge service for inspecting, repairing and replacing for the items within this warranty period; However the freight charges are the customer’s responsibility.
INFORMATION ABOUT YOUR WARRANTY COVERAGE
This warranty does not cover damages or failure attributable to:
- Toilets installed with obvious visual defects.
- Rough handling or improper operation.
- The presence of sediment or impurity in the water supply system used.
- Defects or damages to toilets caused by installation that does not comply strictly with the instructions set forth in the Recognized Plumbing Industry Practice.
- Defects or damage to toilets caused by severe accidents (e.g. fire, electric surge, etc.)
- Damage caused by flooding or standing water from leaking pipes, faucets, household appliances, etc.; Up to and including flooding and any damage caused by acts of God.
NOTES ON WARRANTY
This warranty applies only to the original purchaser and installation site and is not transferable.
FOR WARRANTY SERVICE
- To make a claim, contact the DISTRIBUTOR no later than 30 days following the date of discovery or detection of defect.
- Proof of purchase, such as the bill of sale is mandatory when requesting warranty service.
- The DISTRIBUTOR reserves the right to designate a representative to inspect the vanity for analysis.
- No unauthorized person, installer, dealer, agent or employee of the DISTRIBUTOR or any representative is entitled to assume any liability on behalf of the DISTRIBUTOR relating to the sale of this product or has the authority to increase or alter the obligations or limitations of this warranty.
INSTALLATION PICTURE
Save this manual for future reference
HEAD OFFICE
2800 Etienne Lenoir, Laval
Quebec H7R 0A3 Canada
Customer service
Tel.: 1-866-839-2888
Fax: 1-866-922-9990
customerservice@ovedecors.com
8:00 am – 5:00 pm E.S.T Monday – Friday
English and French speaking representatives available
KEEP THIS INFORMATION
Purchase date __
Product Tracking Reference ___
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>