Shark HD400 Flex Style Instruction Manual
- June 16, 2024
- Shark
Table of Contents
Shark HD400 Flex Style
Product Information
Specifications
- Voltage: 120V~, 60Hz
- Power: 1300 Watts
Product Usage Instructions
Safety Precautions
When using the FlexStyleTM, it is important to follow these safety
precautions:
- For household use only.
- Read all instructions before using and save them for future reference.
- Keep the appliance away from water.
- Always unplug the unit immediately after use.
- Do not use the product while bathing.
- Avoid placing or storing the appliance where it can fall into a tub or sink.
- Do not place the appliance in water or any other liquid.
- If the appliance falls into water, unplug it immediately and do not reach into the water.
- Never leave the appliance unattended when plugged in.
- Supervise children or individuals with disabilities when they are using the appliance.
- Use the appliance only for its intended purpose as described in the manual.
- Do not use attachments not recommended by the manufacturer.
- Check the cord and plug for any damage before operating the appliance.
- Avoid contact between the cord and heated surfaces.
- Do not wrap the cord around the appliance.
- Ensure that the air openings of the appliance are not blocked.
Operating Instructions
- Turn the styler on and off.
- Adjust the airflow by pressing the button for low, medium, or high airflow.
- Adjust the temperature by pressing the button for no heat, low, medium, or high temperature.
- Press and hold the Cool Shot button for a cool burst of air to set your style.
- To attach any accessories included with your model, press them into the nozzle outlet until they click in place.
- To remove accessories, slide the lock down and lift the accessory off of the nozzle using the touchpoints identified in your Style Guide.
- To switch between styling wand mode and hair dryer mode, slide down the lock and rotate the nozzle left or right until it clicks into place.
- Press the ALCI button to reset the dryer if needed.
For further operating instructions, consult the Styling Guide or scan the QR code provided.
Storage, Cord Safety, and Maintenance/Cleaning
To ensure proper storage, cord safety, and maintenance/cleaning of your
FlexStyleTM, follow these guidelines:
- After use, allow the appliance to cool down before storing it in a safe place.
- Do not wrap the cord around the appliance.
- Regularly check the cord for any damage and replace if necessary.
- Clean the appliance according to the instructions provided in the manual.
Troubleshooting & Error Codes
Overheating
If the hair dryer is overheating or shuts off, it may be due to a reduction
in airflow or airflow blockages. Follow these steps to troubleshoot the issue:
- Ensure that the air openings of the appliance are not blocked.
- Remove any obstructions from the nozzle or filter.
- Clean the appliance according to the maintenance instructions provided in the manual.
FAQ
-
Where can I find accessories and replacement parts for my FlexStyleTM?
You can visit sharkclean.com/accessories for accessories and replacement parts. -
Where can I find full instructions, warranty information, and how-tos?
You can scan the QR code provided or visit https://manual-hub.com/ for full instructions, warranty information, and how-tos.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following:
FOR HOUSEHOLD USE ONLY
READ ALL INSTRUCTIONS BEFORE USING—SAVE THESE INSTRUCTIONS
WARNINGS: KEEP AWAY FROM WATER
DANGER
As with most electrical appliances, electrical parts are electrically live
even when the switch is off.
WARNING
To reduce the risk of death by electric shock:
- A lways unplug the unit immediately after using.
- Do not use while bathing.
- Do not place or store appliance where it can fall or be pulled into a tub or sink.
- Do not place in or drop into water or other liquid.
- If an appliance falls into water, unplug the unit immediately. Do not reach into the water.
WARNING
To reduce the risk of burns, electrocution, fire, or injury to persons:
- An appliance should never be left unattended when plugged in.
- Close supervision is necessary when this appliance is used by, on, or near children or individuals with certain disabilities.
- Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
- Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped, damaged, or dropped into water.
- Keep the cord away from heated surfaces.
- Do not wrap the cord around the appliance.
- Never block the air openings of the appliance or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
- Never use while sleeping.
- Never drop or insert any object into any opening.
- Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
- Do not use an extension cord with this appliance.
- Do not direct hot air toward eyes or other heat-sensitive areas.
- Attachments may be hot during use. Allow them to cool before handling.
- Do not place appliance on any surface while it is operating.
- While using the appliance, keep your hair away from the air inlets.
- Do not operate with a voltage converter.
SAVE THESE INSTRUCTIONS
OPERATING INSTRUCTIONS
- Turn the styler on and off.
- Adjust the airflow. Pressing the button allows you to choose a low, medium, or high airflow.
- Adjust the temperature. Pressing the button allows you to choose no heat, low, medium or high temperature.
- Press and hold the Cool Shot button for a cool burst of air to set your style.
- To attach any accessories included with your model, press them into the nozzle outlet. You will know they are properly attached when they click in place.
- To remove any accessories included in your model, slide the lock down and lift the accessory off of the nozzle by holding onto the touchpoints identified in your Style Guide.
- To change from styling wand mode to hair dryer mode, slide down the lock and rotate the nozzle left. Keep rotating the nozzle until it clicks into place in hair dryer mode. To change from hair dryer mode to styling wand mode, slide down the lock and rotate the nozzle right.
- Press the ALCI button to rest the dryer. See Troubleshooting & Error Codes for more information.
For further operating instructions, please consult the Styling Guide or scan the QR code.
Storage, Cord Safety, and Maintenance/Cleaning:
- Ensure the cord is not knotted, twisted, or wrapped around any nearby objects when in use.
- Store the unit in a dry location away from water and other heat sources.
- Regularly clean the filer at the bottom of the unit. To clean the filter, first slide the filter cover off the bottom of the unit. Then use a new toothbrush to brush off any dust or debris on the filter. Once the filter is clean, slide the filter cover back on the unit until it clicks in place.
TROUBLESHOOTING
MAINTENANCE/CLEANING
Reduction in Airflow or Overheating
A change in airflow or air power, airflow blockages, and/or visible buildup on
the inlet at the bottom of the unit indicates your unit needs to be cleaned.
We recommend using a new toothbrush to clean off the filter at the bottom of
the unit.
ALCI OPERATION
Electricity flickers or trips circuit breaker during use.
This dryer is equipped with an Appliance Leakage Circuit Interrupter (ALCI), a
safety feature that renders it inoperable under abnormal conditions. Should
the dryer turn off in use, press the red Reset button on the plug and the
dryer should function normally. If the dryer does not reset, please check your
circuit breaker. If the issue persists, ensure there are no other appliances
plugged in within the room where the dryer is being used. Do not use the dryer
with a power strip.
OVERHEATING
Hair dryer is overheating or shuts off.
This unit is equipped with a temperature-protective thermostat. If for some
reason your hair dryer overheats, the thermostat will automatically turn the
unit off. To prevent power-down recurrence, unplug the hair dryer and set it
aside to cool, or cool down using the cool shot button during use. Overheating
may result if the unit is powered on for a long duration, or can indicate a
blockage or dust buildup. We recommend using a new toothbrush to clean off the
filter at the bottom of the unit. If overheating continues to occur, contact
Customer Service at 855-522-0912.
If you are experiencing a different error code, please scan the QR code for additional troubleshooting or contact Customer Service at 855-522-0912.
TWO (2) YEAR LIMITED WARRANTY
The Two (2) Year Limited Warranty applies to purchases made from authorized
retailers of SharkNinja Operating LLC. Warranty coverage applies to the
original owner and to the original product only and is not transferable.
SharkNinja warrants that the unit shall be free from defects in material and
workmanship for a period of two (2) years from the date of purchase when it is
used under normal household conditions and maintained according to the
requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
- The original unit and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion, will be repaired or replaced up to two (2) years from the original purchase date.
- In the event a replacement unit is issued, the warranty coverage ends six (6) months following the receipt date of the replacement unit or the remainder of the existing warranty, whichever is later. SharkNinja reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
- Normal wear and tear of wearable parts (such as accessories), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are available for purchase at sharkclean.com.
- Any unit that has been tampered with or used for commercial purposes.
- Damage caused by misuse, abuse, negligent handling, failure to perform required maintenance (e.g., failure to keep the well of the motor base clear of food spills and other debris), or damage due to mishandling in transit.
- Consequential and incidental damages.
- Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the repair is performed by a repair person not authorized by SharkNinja.
- Products purchased, used, or operated outside North America.
How to get service
- If your appliance fails to operate properly while in use under normal household conditions within the warranty period, visit sharkbeauty.com for product care and maintenance self-help. Our Customer Service Specialists are also available at 855-522-0912 to assist with product support and warranty service options, including the possibility of upgrading to our VIP warranty service options for select product categories. So we may better assist you, please register your product online at registeryourshark.com and have the product on hand when you call.
- SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of $20.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call 855-522-0912 to initiate
a warranty claim.
You will need the receipt as proof of purchase. We also ask that you register
your product online at registeryourshark. com and have the product on hand
when you call, so we may better assist you. A Customer Service Specialist will
provide you with return and packing instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other
rights that vary from state to state. Some states do not permit the exclusion
or limitation of incidental or consequential damages, so the above may not
apply to you.
FCC WARNINGS
This unit has been tested and found to comply with FCC limits for Class B
digital devices. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This unit
generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. Operation of this unit may not cause harmful
interference, and this unit must accept any interference received, including
interference that may cause undesired operation. To see if this unit
interferes with radio or television reception, try turning it off and on.
To correct any interference:
- Reorient or relocate the receiving antenna.
- Increase the distance between the unit and the receiver.
- Connect the unit to a different outlet than the receiver.
- Consult the dealer or an experienced technician for help.
Caution: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate it.
For accessories and replacement parts, visit sharkclean.com/accessories
TECHNICAL SPECIFICATIONS
- Voltage: 120V~, 60Hz
- Power: 1300 Watts
References
- Hair Care & Styling Tools for All Hair Types – Shark Beauty™ US
- Find Shark® Clean Parts & Accessories - Shark®
- Manual-Hub.com – Free PDF manuals!