BLITZSHARK SRK-DG18L 12V Kids Ride Car Installation Guide

June 16, 2024
BLITZSHARK

BLITZSHARK SRK-DG18L 12V Kids Ride Car Installation Guide

NOTE
Please install this ride-on car according to the instruction and the installation video on the detail page of your purchased product.

Charge for 4-6 hrs before initial use.

After initial charge, follow the normal recommended charging time.

SAFETY

NOTE: For best performance, only use this vehicle on flat and hard surfaces
AGE RANGE: 37-96 months
WEIGHT CAPACITY: 66LBS (30KG) is the maximum weight for 1 rider

WARNING

  • This product contains small parts. Keep children away during assembly. Make sure to remove all packaging
    material and parts from underneath the vehicle body.

  • Never open the battery. Batteries contain lead and lead compounds (acids).

  • Limbs, hair and clothing can get caughtin moving parts. Always wear shoes, keep limbs away from moving parts and do not wear loose clothing while operating this vhicle.

  • This vehicle does not have separate braking system. Do not leave a child unattended during operation. Do not use it in a location that may require emergency stop function as this could result in loss of control, which may cause serious injury or death.

  • Use of this vehice near streets, motor vehicles, steps, bodies of water, sloped surfaces, hills, wet areas, flammable vapors, in alleys, at night or in the dark could result in an unexpected accident.

  • Use of this vehicle in unsafe conditions such as snow, rain, loose dirt, mud, sand or gravel may result in an unexpected accident such as tipping over and could damage the electrical system or battery.

  • Do not operate this vehicle in an unsafe manner. Examples include but are not limited to

    • Pulling the vehicle with another vehicle or similar device
    • Allowing more than one child to ride
    • Pushing the user
    • Traveling at an unsafe speed

WARNING

  • Use of a battery or charger other than the supplied rechargeable battery and charger may cause a fire or
    explosion. Only use the supplied battery and charger.

  • Use of the rechargeable battery and charger for any other product may result in overheating, fire or explosion.

  • Never use the supplied rechargeable battery and charger with another product.

  • Explosive gases are created during charging. Charge the battery in a well ventilated area. Do not charge the battery near heat or flammable materials.

  • Contact between the positive and negative terminals may result in fire or explosion. Avoid direct contact between the terminals. Picking up the battery by the wires or charger can cause damage to the battery and may result in a fire. Always pick up the battery by its case or handles.

  • Liquids on the battery may cause fire or electric shock. Always keep all liquids away from the battery and keep the battery dry. Contact or exposure to battery leakage (lead acid) may cause serious injury. If contact or exposure occurs immediately call your physician. If the chemical is on the skin or in the eyes, flush with cool water for 15 minutes. If the chemical was swallowed, immediately give the person water or milk. Do not give water or milk if the patient is vomiting or has a decreased level of alertness. Do not induce vomiting.

  • Battery posts, terminals and related accessories contain lead and lead compounds (acid).

  • Tampering or modifying the electric circuit system may cause a shock, fire or explosion and permanently damage the system. Exposed wiring and circuitry in the charger may cause electric shock. Always keep the charger housing closed.

WARNING

  • Never leave a child unattended.

  • Always sit in the seat when using this vehicle.

  • Keep your hands, hair and clothes away from moving part.

  • Always wear shoes when operating this vehicle.

  • Children under 3 years of age cannot use the vehicle.

  • Only drive on level ground.

  • Do not go near swimming pools or other bodies of
    water, drop-offs or up and down steep inclines.

  • Do not drive the vehicle into loose dirt, mud, sand, fine gravel or on wet surfaces.

  • Do not drive the vehicle on streets or near cars.

TOOLS REQUIRED

  • 2 PERSON ASSEMBLY

  • APPROXIMATELY 45 MIN ASSEMBLY

  • SCREWDRIVER (BRING YOUR OWN)

  • WRENCH (PROVIDED)

  • Car body

    1 PCS

  • Windshield

    1 PCS

  • Steering wheel

    1 PCS

  • Seat

    1 PCS

  • Motors

    2 PCS

  • Front wheels

    2 PCS

  • Rear wheels

    2 PCS

  • Front wheels cover

    2 PCS

  • Rear wheels cover

    2 PCS

  • Remote control

    1 PCS

  • Mirrors

    2 PCS

  • Charger

    1 PCS

  • Manual

    1 PCS

Below are the photos of front wheels cover (left) and rear wheels cover (right) for reference, in which only the design of red decorative caliper is different.

PRODUCT ASSEMBLY

Part 1: Front Wheel Assembly

  • Gasket-Wheel-Gasket-Nut-wheel cover;
    1. Insert one metal gasket into the axle.
    2. Put the wheels into the axle.
    3. Insert another metal gasket into the axle.
    4. Put the nut into the axle and tighten it.
    5. Put the wheel cover onto the wheel. (Please refer to the picture in the upper right corner for the front wheel cover.)

Part 2: Rear Wheel Assembly

  • Motor-Wheel-Gasket-Nut-wheel cover;
1. Install motor into the axle first.
2. Put the wheels into the axle.
3. Insert one metal gasket into the axle.
4. Put the nutinto the axle and tighten it.
5. Put the wheel cover onto the wheel. (Please refer to the picture in the upper right corner for the rear wheel cover.)

Part 3: Steering Wheel Assembly

  1. Connect the wires of steering wheel with the wires from dashboard. Then put the connector and wires into the hole, in order to avoid being cut off during steering wheel installation.
  2. Take off the screw on the steering wheel axle.
  3. Slide the steering wheel into the axle.
  4. Tighten the nut to lock the steering wheel.

Part 4: Windshield Assembly

Fit the windshield to car body and press down, make sure it will be in the right way.
(There would be a clicking sound when each snap lock well.)

Part 5: Mirror Assembly

Fit the mirror to the car body.

Part 6: Seat Assembly

  1. Connect the red positive battery cable under the seat. Figure (a) shows an example.

  2. Fit the seat as shown in Figure (b) (make sure the seat into the slots on the rear of the vehicle);

  3. Insert the screw through the seat back-top and into the vehicle body, and tighten it with a screwdriver.

DASHBARD DIAGRAM

Functions:

  1. Pedal;
  2. Lights switch;
  3. Forward, stop, back;
  4. Speed switch;
  5. Power switch;
  6. Multi-media;

Pictures are for reference only; functions may vary with different model and setting; please adhere to the original products as standard.

  1. Socket for Flash Drives
  2. Power Display
  3. MP3 Input
  4. Horn (Pressing for a longer time to lower the volume)
  5. Pause (Pressing once to pause the music, pressing again to resume the music)
  6. Music (Pressing for a longer time to Higher the volume)
  7. Model choose (MP3, Flash Drives or Mobile wireless connection via YJ-BTcar)
  • Pictures are for reference only; functions may vary with different model and setting; please adhere to the original products as standard.

REMOTE CONTROL DIAGRAM

This remote must be used by adult only.

2.4G HZ Remote Control Operations Guide:
Step 1: The Remote Controller is loaded with two AAA batteries (nonincluded).
Step 2: Turn off the power switch on the vehicle.
Step 3: Hold down “M” keys for 3 seconds to start match code.
When the LED flicker, please turn on the vehicle power switch. Once the LED lights stop flashing, then the code is successful.

Key Description:
Forward Backlit Right, “S” Speed, “P” Stop.

  • Press the “S” key to set the speed, a light is low, two lights for medium-speed, three lights for high-speed.
  • Press “P” key to stop, All LED flicker

Pictures are for reference only, functions may vary with different model and setting, please adhere to the original products as standard.
This product does not provide dry batteries.

WARNING

Not for children under 37 months. Small parts. Choking hazard.

  • Load two AAA (1.5V) batteries according to the diagram.
  • Non-rechargeable batteries are not to be recharged.
  • Different types of batteries or new and used batteries are not to be mixed.
  • Batteries are to be inserted with the correct polarity.
  • Exhausted batteries are to be removed from the toy.
  • The supply terminals are not to be short-circuited.
  • The packaging must be retained since it contains important information.
  • Charging battery must only be under adult’ s supervision.

CHARGING INSTRUCTIONS

WARNING

  • ONLY an adult is allowed charge and recharge the battery!

  • This product with Charging Protection: when charging, all functions will be cut off.

  • Battery polarity cannot be reversed. Please ensure the red wire is connected to the red battery terminal and the blac| wire is connected to the black battery terminal.

  • Before the first use, it recommended to charge the battery for 4-6 hours, but not more than 10 hours.

  • When the vehicle begins to run slowly, recharge the battery.

  • After each use or once a month minimum recharge time as 8 to 12 hours, less than 20 hours at most. Failure to charge| the battery as directed will cause permanent damage to battery and will void warranty.

  • Use the only rechargeable battery and charger supplied with your vehicle. NEVER substitute the battery or the charger with another brand. Using another battery or charger may cause a fire or explosion.

  • Do not use the battery or charger for any other product.

  • The charger may feel warm during charging. If excessively hot, unplug and replace.

    1. Plug the charger port into the input socket.
    2. Plug the charger plug into a wall outlet. The battery will begin charging
    3. Unplug the charger when the battery is fully charged.

Battery Disposal

  • Dead battery: it eventually loses the ability to hold a charge. Depending on the amount of use, and varying conditions, the battery should operate for one to three years.
  • Important! Lead-acid batteries are completely recyclable. Recycle the dead battery responsibly. It is illegal in most areas to incinerate lead acid batteries or dispose of them in landfills. Dispose of in accordance with all applicable local, state, and national regulations.
  • Do not throw the battery away with your regular household waste!

TROUBLESHOOTING

Problem Possible Cause Remedy
Vehicle does not run Battery low on power Recharge battery (see Battery:

Recharge Interval and Time)
Thermal fuse has tripped| Let the vehicle rest for 5 to 10 minutes before continuing normal operation.
Battery connector or wires are loose| Check that the battery connectors are firmly plugged into each other. If wires are loose around the motor, please contact customer service department by email: care@joywhale.com
Battery is dead| Replace battery (Please contact customer service department by email: care@joywhale.com for further help)
Electrical system is damaged| Please contact customer service department by email: care@joywhale.com
Motor is damaged| Please contact customer service department by email: care@joywhale.com
Vehicle does not run very long| Battery is under charged| Check that the battery connectors are firmly plugged into each other when recharging
Loud grinding or clicking noises coming from motor or gear box| Motor or gears are damaged| Please contact customer service department by email: care@joywhale.com
Vehicle runs sluggishly or beeping occurs| Battery low on power| Recharge battery
Battery s old| Replace battery (Please contact customer service department by email: care@joywhale.com for further help)
Vehicles over loaded| Reduce weight on vehicle (see User Requirements and Safety Warnings)
Vehicles being used in harsh conditions| Operate the vehicle level ground and firm surfaces (see User Requirements and Safety Warnings)
Vehicle needs a push to go forward| Poor contact of wires or connectors| Check that battery connectors are firmly plugged into each other. If wires are loose around the motor, please contact customer service department by email: care@joywhale.com
“Dead Spot” on motor| Ahead spot means the electric power is not being delivered to the terminal connection and the vehicle needs repair. Please contact customer service department by email: care@joywhale.com
12V Battery will not recharge| Battery connector or adapter connector is loose| Check that battery connectors are firmly plugged into each other
Charger not plugged-in| Check that battery charger is plugged into a working wall outlet
Chargers not working (lights not glowing)| Please contact customer service department by email: care@joywhale.com
Battery bubbles or gurgles when charging| This is normal and not a cause for condemn|
Charger feels warm when recharging| This is normal and not a cause for conked|

CARING FORYOUR RIDE-ON

  • Park the vehicle indoors or cover it with a tarp to protect it from wet weather.
  • Do not leave the vehicle in the sun for long periods of time or fading may occur. Store in shade or cover with tarp.
  • Do not wash the vehicle with a hose.
  • Do not wash the vehicle with soap.
  • Charge battery at least once a month to prolong the life of the battery.

CARING FORYOURRIDE-ON

If you have any questions about the steps of installing the product or if there are any problems with the product in use, please feel free to contact the customer service of your purchase platform by email.

WARNING
The battery on the vehicle is not replaceable.

  • Do not mix old and new batteries.
  • Do not mix alkaline, standard(carbon-zinc) or recharge able batteries,
  • Non-rechargeable batteries should not be charged.
  • Rechargeable batteries should be charged under adult supervision only.
  • Exhausted batteries should be removed.
  • The supply terminals should not be short-circuited.
  • Do not put batteries next to or in a heat source(fire, electronic heating device, etc.).
  • Do not hit batteries against hard objects. Do not submerge batteries in water.
  • Batteries should be inserted with the correct polarity.

IMPORTANT

  • Always charge battery for 4-6hrs the first time you use it.
  • Always charge battery for 8-12hrs after each use.
  • Charge the battery once a month, even if you are not using your vehicle

WARNING

  • Protective equipment should be worn. Not to be used in traffic.
  • The toy should be used with caution since skill is required to avoid falls or collisions causing injury to the user or third parties.
  • To reduce the risk of injury, adult supervision is required. Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water; always wear shoes, and never allow more than one rider.

WARNING
CHOKING HAZARD-Small parts.
Not for children under 3yrs.
To reduce the risk of injury, adult supervision is required. Never use in roadways. Never motor vehicles, on or near steep inclines or steps, swimming poor’s or other bodies of water; always wear shoes, and never allow more than one rider.

WARNING
ADULT ASSEMBLY REQUIRED

WARNING
Not to be used in traffic.

CARING FORYOUR RIDE-ON

Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following. measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio / TV technician for help.

MAINTENANCE

The vehicle should be checked for damage, missing or badly worn parts before use.

  • Check the tightness of the fasteners before each use.
  • Check the tightness of the wheels.
  • Ensure the battery is securely in place before use.
  • Occasionally use lightweight oil to lubricate moving parts such as wheels and steering linkage.
  • Do not use oil on plastic or nylon parts. No lubrication is required.
  • Store the vehicle indoors or cover it with a tarp to protect it from the wet weather. Keep it away from  sources of heat, such as stoves and heaters.
  • Clean the vehicle with a soft, dry cloth. To restore shine to plastic parts, use a non-wax furniture polish. Do not use car wax, abrasive cleaners or wash the vehicle with soap and water. Water will damage the motor, electrical system and battery.
  • Joywhale recommend you ask professional advice from our technical team if you need maintenance or repair service. Official email address of Joywhale: care@joywhale.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals