tp-link AP9665 Omada Pro Ceiling Mount AP User Guide

AP9665 Omada Pro Ceiling Mount AP
User Guide

AP9665 Omada Pro Ceiling Mount AP

Regulatory Compliance
Ceiling Mount AP
1910013332 REV1.2.0

FCC Compliance Information Statement

Product Name: Omada Pro Ceiling Mount Access Point
Model Number: AP9635 / AP9650 / AP9665 / AP9670 / AP9778
Responsible party: TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is  encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
   Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
   Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
   FCC RF Radiation Exposure Statement:
   This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
   “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all  persons and must not be collocated or operating in conjunction with any other antenna or transmitter.”
   For AP9778:
   FCC regulations restrict operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying  above 10000 feet. Operation of transmitters in the 5.9256.425 GHz band is prohibited for control of or communications with unmanned aircraft systems.
   We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the  equipment is properly maintained and operated. Issue Date: 2023-12-28

CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

OPERATING FREQUENCY (the maximum transmitted power)
For AP9635 V1 / AP9650 / AP9670:
2412 MHz -2472 MHz (20dBm)
5150 MHz -5250 MHz (23dBm)
5250 MHz -5350 MHz (23dBm)
5470 MHz -5725 MHz (30dBm)
For AP9635 V2 / AP9665:
2402 MHz-2480 MHz (10dBm)
2412 MHz -2472 MHz (20dBm)
5150 MHz -5250 MHz (23dBm)
5250 MHz -5350 MHz (23dBm)
5470 MHz -5725 MHz (30dBm)
For AP9778:
2402 MHz-2480 MHz (10dBm)
2412 MHz -2472 MHz (20dBm)
5150 MHz -5250 MHz (23dBm)
5250 MHz -5350 MHz (23dBm)
5470 MHz -5725 MHz (30dBm)
6105 MHz -6425 MHz (23dBm)

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU Declaration of Conformity  may be found at https://www.tp-link.com/en/support/ce/.
RF Exposure Information
This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
The device complies with RF specifications when the device used at 20cm from your body.
National Restrictions
For AP9635 / AP9650 / AP9665 / AP9670:
Frequency band: 5150 – 5250 MHz:
Indoor use: Inside buildings only. Installations and use inside road vehicles and train carriages are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached to a fixed installation or to the external body of  road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 – 5250 MHz band. Frequency band: 5250 – 5350 MHz:
Indoor use: Inside buildings only. Installations and use in road vehicles, trains and aircraft are not permitted. Outdoor use is not permitted.
Frequency band: 5470 – 5725 MHz:
Installations and use in road vehicles, trains and aircraft and use for unmanned aircraft systems (UAS) are not permitted.
For AP9778:
Frequency band: 5150 – 5250 MHz:
Indoor use: Inside buildings only. Installations and use inside road vehicles and train carriages are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached to a fixed installation or to the external body of  road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 – 5250 MHz band.
Frequency band: 5250 – 5350 MHz:
Indoor use: Inside buildings only. Installations and use in road vehicles, trains and aircraft are not permitted. Outdoor use is not permitted.
Frequency band: 5470 – 5725 MHz:
Installations and use in road vehicles, trains and aircraft and use for unmanned aircraft systems (UAS) are not permitted.
Frequency band 5945 -6425MHz:
Restricted to indoor use, including in trains with metal-coated windows and aircraft.
Outdoor use, including in road vehicles, is not permitted.

UKCA Mark
UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK Declaration of Conformity may be found at https://www.tp- link.com/support/ukca 
National Restrictions
Attention: This device may only be used indoors in Great Britain.

| UK
---|---

Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Caution
For AP9635 / AP9665:

1. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; 5150 MHz to 5350 MHz is restricted to indoor operations in Hong  Kong.
   For AP9650 / AP9670 / AP9778:
2. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; 5150 MHz to 5350 MHz is restricted to indoor operations in Hong Kong.
   DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350 MHz, 54705600MHz, and 5650-5725MHz.
   For AP9778:
   ISED regulations restrict operation of this device to indoor use only. The operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying  above 10000 feet. Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications with unmanned aircraft systems.
   Pour AP9778:

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
Korea Warning Statements
NCC Notice & BSMI Notice

Safety Information

• Keep the device away from water, fire, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended.
• Do not use the device where wireless devices are not allowed
• Adapter shall be installed near the equipment and shall be easily accessible.
• Operating Temperature: 0℃ ~ 40 ℃ (32 ℉ ~ 104  ℉ )
• This product uses radios and other components that emit electromagnetic fields.
  Electromagnetic fields and magnets may interfere with pacemakers and other implanted medical devices. Always keep the product and its power adapter more than 15 cm (6 inches) away from any pacemakers or other implanted  medical devices. If you suspect your product is interfering with your pacemaker or any other implanted medical device, turn off your product and consult your physician for information specific to your medical device.
  Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

Explanation of the symbols on the product label
Note: The Equipment marking is at the bottom of the device. Symbols may vary from products.

Symbol	Explanation

Class II equipment
| Class II equipment with functional earthing
| Alternating current
| Direct current
| Polarity of d.c. power connector
| For indoor use only
| Dangerous voltage
| Caution, risk of electric shock
| Energy efficiency Marking
| Protective earth
| Earth
| Frame or chassis
| Functional earthing
| Caution, hot surface
| Caution
| Operator’s manual
| Stand-by
| ON/”OFF” (push-push)
| Fuse
| Fuse is used in neutral N
| RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be  handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
| Caution, avoid listening at high volume levels for long periods
| Disconnection, all power plugs
m| Switch of mini-gap construction
| Switch of micro-gap construction (for US version) Switch of micro-gap / micro-disconnection construction (for other versions except US)
| Switch without contact gap (Semiconductor switching device)

Mounting Requirements

For safety, we recommend you to use the original screws in the package when mounting. The following are alternatives to mount the device on the wall:

• (For AP9635 / AP9650 / AP9665 / AP9670) Use 4 screws which comply with ANSI B1.1 4# standard and are longer than 15 mm.
• (For AP9778) Use 6 screws which comply with ANSI B1.1 4# standard and are longer than 15 mm.

References

• Link: Simple, secure one-click payments
• CE Regulatory Compliance | TP-Link
• Regulatory Compliance | TP-Link
• WiFi Networking Equipment for Home & Business | TP-Link

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>