BuiltRough BR-TRS-027 Rocker Step User Guide

BuiltRough BR-TRS-027 Rocker Step

Specifications

• Part Number : BR-TRS-027
• Fits : 2005-Up Toyota Tacoma Double Cab
• Installation Time : 60-120 minutes
• Cutting Not Required
• Drilling Not Required

Product Usage Instructions

Before Installation

1. Remove contents from the box and verify that all parts are present according to the parts list.
2. Read the instructions carefully.
3. Note that the bumper is heavy, so assistance is highly recommended to avoid possible injury or damage to the vehicle.

Part List

• 27-L for Driver/Front Left Side
• 27-R for Passenger/Right Side
• Driver/Left Side Front Bracket
• Passenger/Right Side Front Bracket
• Driver/Left Side Center/Rear Bracket x2
• Passenger/Right Side Center/Rear Bracket x2
• Rocker Step x12
• 8mm x 30mm Hex Bolt x12
• 8mm Flat Washer x12
• 8mm Lock Washer x12
• 8mm x 25mm Combo Bolt x12

Step 1
Starting on the Driver/Left front of the vehicle, remove the plastic plugs (or hex bolts) covering the threaded holes in the body panel.

Step 2
Select the Driver/Left Front Mounting Bracket. Attach the Bracket to the vehicle using (2) 8mm Hex Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers. Do not tighten the hardware at this time.

Step 3
Move along the body panel to the center and rear mounting locations. Select the remaining (2) Driver/Left Center/Rear Mounting Brackets. Repeat Step 2 to install the Mounting Brackets on the center and rear mounting locations. Do not tighten the hardware.

Step 4
Select the Driver/Left Rocker Step. Carefully place the Rocker Step on the brackets. Attach the Rocker Step to the Mounting Brackets using (6) 8mm Combo Bolts. Do not tighten the hardware.

Step 5
Level and adjust the Rocker Step, then fully tighten all hardware.

Step 6
Repeat Steps 1-5 to attach the Passenger/Right Rocker Step.

Step 7
Do periodic inspections to ensure that all hardware is secure and tight.

Attention
To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Rocker Step.

FAQ

• Q: Is cutting required for installation?
  A: No, cutting is not required for installation.

• Q: Is drilling required for installation?
  A: No, drilling is not required for installation.

• Q: What tools are required for installation?
  A: You will need a 10mm wrench, 13mm wrench, 16mm wrench, 18mm wrench, 4mm Allen wrench, 5mm Allen wrench, 6mm Allen wrench, and 8mm Allen wrench.

• Q: How long does the installation usually take?
  A: The installation time is approximately 60-120 minutes.

Rocker Step
PART NO. BR-TRS-027

FITS:| 2005-Up Toyota Tacoma Double Cab

Torque & Tools

Fastener Size| Tightening Torque (ft-lbs)| Wrench Required| Allen Wrench Required
---|---|---|---
□ 6mm| □ 7-8.5| | □ 10mm| | □ 4mm
■ 8mm| ■18-20| ■ 13mm| □ 5mm
□ 10mm| □ 35-40| □ 16mm| □ 6mm
□ 12mm| □ 60-70| □ 18mm| □ 8mm

BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT DEPEND ON THE PARTS LIST. READ INSTRUCTIONS CAREFULLY. BUMPER IS HEAVY, ASSISTANCE IS HIGHLY RECOMMENDED TO AVOID POSSIBLE INJURY OR DAMAGE TO THE VEHICLE.

Part List

Tools For Use

P LEASE NOTE THAT THE FOLLOWING P ICTURES ARE BASED ON THE DRIVER S IDE INSTALLATION

• STEP 1
  Starting on the Driver/Left front of the vehicle, remove the plastic plugs, (or hex bolts), covering the threaded holes in the body panel, (Fig 1).

• STEP 2
  Select the Driver/Left Front Mounting Bracket. Attach the Bracket to the vehicle with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Fig 2). Do not tighten hardware at t his time.

• STEP 3
  Move along the body panel to the center and rear mounting location, (Figs 3 & 4). Select remaining (2) Driver/Left Center/Rear Mounting Brackets. Repeat Step 2 to install the Mounting Bracket on center and rear mounting locations, (Fig 5). Do not tighten hardware.

• STEP 4
  Select the Driver/Left Rocker Step. NOTE: The D river/Left Rocker Step will have a “27-L” on the fr ont. Carefully place Rocker Step on the brackets. IMPORTANT : Do not slide the Rocker Step front to back or damage to the finish may result. Attach Rocker Step to the Mounting B rackets with (6) 8mm Combo Bolts, (Fig 6). Do not tighten hardware.

• STEP 5
  Level and adjust the Rocker Step and fully tighten all hardware.

• STEP 6
  Repeat Steps 1—5 to attach the Passenger/Right Rocker Step.

• STEP 7
  Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Attention

• To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish.
• Mild soap may be used also to clean the Rocker Step.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>