Aveek F-4A Professional Audio Mixer Owner’s Manual

veek F-4A Professional Audio Mixer Owner’s Manual

Compatible Devices and Connection Methods

INPUT &OUTPUT

MIC IPPUT| XLR input jacks x 2| REC OUT| RCA L/R Line output x 1 pair
6.35MM INPUT| 6.35mm L/R Line input jacks x 1 pair| MAIN OUT| 6.35mm L/R output x 1 pair
RCA INPUT| RCA L/R Line input jacks x 1 pair| MONITOR OUT| 3.5mm monitor output jack x 1
USB 2.0 INPUT| USB input x 1 for record and playback| Bluetooth INPUT| Bluetooth wireless input x 1
USB-B INPUT| USB-B input/output 1 for record and playback| |

Welcome

Thank you for purchasing the F-4A audio mixer,
Please read this manual carefully for proper use of your F-4A audio mixer, Should you need technical assistance please email our thechnical help at “all-after-sales@outlook.com“.

Main Features

• 2 XLR Mic Linel Input + 1 pair RCA L/R Line Input and 1 pair 6,35mm L/R Line Input,
• USB-B interface can connect the PC for recroding ouput and playing audio.
• Bluetooth/USB playback
• Built-in 48V phantom power supply
• Gain and treble and bass adjustment, Delay or reverb effects adjustment.

Included Accessories

• Audio mixer*1

• Micro-USB Power Cable *1

• 3AC power adaptor * 1

• USB-B Recording/Data transmission cable (78 inch)

Panel instroduction

1. 1 [MIC/LINE 1-2) 2 XLR mono input jacks
   Used to connect microphones, musical instruments, or audio equipment (CD players, ellc.) to this device. These jacks support both XLR and phone pluge,

2. [PAD +48V] Switch
   When the switch is turned on, the LED lights up to indicate that the device has applied DC 48V phantom power to the MIC LINE 1-2 on mano input XLR port. When using a condenser microphone powered by phantom power, turn on this switch..
   NOTE: If you do not need phantom power supply, be sure to set this switch to off.

   • When operating this switch please observe the following important precautions in order to prevent noise and damage to the unit and exdamat equipment.
   • When the microphone or other equipment connected on the MIC LINE 1-2 does not support the phantom power supply function, make sure that the switch is kept off. When the switch is on, do not connect disconnect the cables on the MIC LINE 1-2.
   • Before operating this switch, set the [LEVEL] knobs of the MIC LINE 1-2 to minimum.

3. [GAIN] knob
   Input channel volume buttons, Adjust these controllers to make the corresponding(PEAK) LED flash briefly when singing and playing at the maximum volume.

   • The volume MIC LINE 1-2 can be individually adjusted..
   • The volume of LINE 3/4/PC and USB/Bluetooth module are share a single GAIN knob control.

4. Equalizer (EQ) knob
   Use the [HIGH] (high band) and (LOW] (low band) knobs to adjust the sound quality. If you do not need to adjust the sound quality, you can set the knob to the “12 o’clock direction” position,

   • The EQ of MIC LINE 1-2 can be individually adjusted on EQ key.
   • The EQ of LINE 34/PC and USB/Bluetooth module are share a single EQ knob control.

5. [EFF] Effect switch
   The EFF control adjusts the effect volume of the only for MIC LINE 1-2. LINE 3-4/PC Bluetooth/USB modules have no reverberation effect,

6. [PEAK] LED
   If will light up when the volume of the input signal or the volume after the equalizer is too high (when it reaches 3dB below the clipping distortion) If it lights up frequently, Tum the [GAIN] knob to the left to decrease the volume:

7. [LEVEL] knob
   Used to adjust the volume balance between each channel. Usually this switch is set to the “3 o’clock direction” position.

   • The volume MIC LINE 1-2 can be individually adjusted GAIN knob control.
   • The volume of LINE 3/4/PC and USB/Bluetooth module are share a single LEVEL knob control

8. [LINE 3/4/PC USB/Bluetooth function] switch
   This switch button is to switch between LINE 3/4/PC or USB/Bluetooth module When you use LINE 3/4/PC, you don’t have to press this button, When you use the USB/Bluetooth module, this button must be pressed. NOTE: Bluetooth and USB functions are only available as one of the two options and connote be uedsimu tenuously.

9. RCA LIR Line Output jacks
   Used for output connections, devices that support RCA jacks.

10. RCAL/R Line Input jacks
    For input connections, devices that support lotus Ineo jacks, For example, CD player, mobile, compeer electronic organ ect.

11. 6,35mm L/R Line Input jacks
    It is used for input connection and supports 6.35mm-line jack devices, For example, CD player, mobile, computer. Electronic organ ect. 12 6.35mm L/R Line Output jacks is used for output connection and supports 6,35 line socket equipment, For example, active speaker, power amplifier ect,

12. USB input
    Used for USB port device input. Such PC, USB Stick, MP3 devices ect, it can be used for music playback and recording to USB stick output,

13. Display
    Used to display USB mode or Bluetooth mode.

14. USB Player /Bluetooth player/USB recording controller
    The first button on the left: switch USB MP3 Player or Bluetooth MP3 Player or USB Stick Recording mode: The second button on the kift: previous song The first button on the right button: playback pause: The second button on the right next song.

15. [DELAY] Delay effect knob
    Adjust the intensity of the delay effect processing for the MIC LINE 1-2 signal.

16. Power switch LED
    The mixer’s power switch indicator

17. [PHONES] output jack
    Used to connect headphones.

18. [REPEAT] Reverb effect knob
    reverberation effect processing for the MIC LINE 1-2 signal.

19. [PHONES] knob
    You can adjust the volume of the sound output from the [PHONES] jack.

20. [MAIN] knob
    All signals volume control knob.

21. [DC5V/Micro
    Power port] Connect the included power cord and AC adapter to power the mixer, or connect to a computer to record and play. There are three ways to supply power.

22. Power up with the supplied AC adapter and power cord connection.

23. It can be connected with the supplied power cord with the power bank.

24. You can connect to your computer with the included power cord.

25. Power switch
    This key is the switch that controls the mixer.

26. USB-B port for PC/Phone Connection
    This USB-B port is designed to connect to a computer/mobile phone for lossless data transfer/recording/ playback, and at the same time to output recordings made on the mixer to a computer/mobile phone. (Note that if you connect a mobile phone, you need an OGT header to transfer data to the mobile phone)

27. PC LED
    This indicator lights up when the USB-B port is connected to a computer or mobile phone.

General Specifications

How to Use the Audio Mixer?

STEP1:

1. Connect the micro-usb power cable to mixer, then connect the Supplied AC adapter.

2. Adjust all level control knobs to zero. Includes [Gain] knob (red), [Level] knob (blue) and [Main] knob (white); Then set the equalizer knob (green) to the center “12 o’clock”

3. Turn on the power switch button.

4. Connect the output device (active speakers or power amplifier + passive speakers) to the output device jack of the mixer.
   

5. Connect the input devices you need in the following order:
   

STEP2:

1. If you connect a device with high output level, such as a CD player or an electric keyboard to connect the channels 1-2, Press the [PAD] switch of the corresponding channel
   

2. Set the [LEVEL] knob as required to adjust the volume balance between the corresponding channels.
   NOTICE There are three functions to adjust the volume: [PAD], [GAIN] and [LEVEL]. Once the [PAD] switch and [GAIN] knob have been set, do not adjust these controls as much as possible. Generally, the volume is adjusted with the [LEVEL] knob.

Operating Steps for Computer Recording

1. First connect the pc or laptop to the mixer using a cable to power it on and then directly open the recording software to record(no need to install a driver)
2. Before connecting to the computer to record, you need to set the computer as follows:

Windows system settings

1. Open the Start menu, and then click Control Panel.

2. Open the sound preferences from the control panel folder.
   

3. Click “Record” and set the microphone to the default value to start recording.

Apple system settings

1. Open the “System Preferenc- es” application.

2. Find “Sound” and click to open it.

3. Click to open the “Output” interface to select the microphone and start recording.
   

How to record via USB jack USB

1. Plug in usb stick, flash drive.

2. Press MODE button until ” USB REC” shown on the LCD and you will hear the voice prompt” Recording
   Mode”, at this time, start recording automatically to USB.

3. Press the button to start or pause recording.
   

4. Press the MODE button to finish recording and save the file in the MP3 format & Play recording file.
   

Operating Steps for Bluetooth Playback

1. Press MODE button until “BT” shown on the LCD and you will hear the voice prompt “The bluetooth device is ready to pair” If Bluetooth is not connected, the word “BT” will keep flashing
2. Open Bluetooth mode on the phone, click “F-4A” to connect successfully, and you will hear the voice prompt “Bluetooth connect successful, and then play music.
3. Press the button to start or pause music, Press the and switch songs.

NOTE: When using Bluetooth and USB functions, Pls press this key (

NOTE: Bluetooth and USB functions are only available as one of the two options and cannot be used simultaneously.

Operating Steps for USB Play Music USB

1. Plugin sub stick, flash drive, MP3
2. Press MODE button until MP3 shown on the LCD and you will hear the voice prompt” Music Play Mode”. Then music automatically plays
3. Press the button to start or pause music, Press the and switch songs.

NOTE: When using Bluetooth and USB functions, Pls press this key

NOTE: Bluetooth and USB functions are only available as one of the two options and cannot be used simultaneously.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>