Underwater Kinetics UK4AA Lighthouse ER Dual User Manual
- June 16, 2024
- Underwater Kinetics
Table of Contents
Underwater Kinetics UK4AA Lighthouse ER Dual
Product Information
Specifications
- Batteries: 4x Alkaline AA/LR6/mignon or Energizer AA Ultimate Lithium
- Lamp Type: High-Intensity LED
- Size: 8.4×2.0x1.60in;21.4×5.1×4.1cm
- Weight: 8.1oz;231g (with batteries and clip)
- Materials: ABS, polycarbonate, copper alloys, stainless steel
- Immersion Depth: 10 feet/3m
Product Usage Instructions
Battery Installation
- Hold the case in the position shown.
- Drop two batteries with the positive + end down into the case.
- Drop two batteries with the positive + end facing up into the case.
- Place the Lamp Head over the mouth of the light and twist it onto the case.
ON/OFF
To operate the light, push in on the black rubber switch located on the case near the head to turn the light ON and OFF.
Spot/Diffuse Beam Selection
Choose between the Spot beam or Wide Angle Diffuse beam by pressing the selector switch button located on the side of the lamp head. Rotate the lamp head to point the beam to the correct position.
Rubber Padded Magnetic Base
A powerful magnet is located in the base of the Lighthouse so that it can be attached to any steel or magnetic surface. It is not attracted to aluminum, copper, or other non-ferrous metals.
Belt/Pocket Clip
A stainless steel or nylon Belt/Pocket Clip can be snapped onto the side of the Lighthouse. First, insert one side of the clip through the slot on the side of the case. Then snap the clip around the case as shown in the illustration.
O-Ring Seal
The O-ring and threads must always be kept clean. Lightly lubricate the O-ring, which seals the rubber-covered bezel and case, with silicone grease.
Pressure Equalizing Vent
Air and gas from battery leakage can pass freely in and out of the Lighthouse through a black triangle-shaped vent in the side of the light. Do not allow dirt or grease to accumulate on the vent or it will not operate properly.
FAQ
Q: What is the warranty for this product?
A: Underwater Kinetics products carry a Limited Lifetime Warranty to the original retail purchaser to be free from defective material and workmanship under normal and intended use. The warranty covers materials used in its products to the original purchaser, as follows: plastics for 10 years, rubber for 3 years, LED and electronics for 2 years, rechargeable batteries for 90 days.
Q: What should I do if I detect a defect in the material or workmanship?
A: In the event the original retail purchaser detects a defect in the material or workmanship, the product along with proof of purchase date should be returned to an authorized Underwater Kinetics dealer or directly to Underwater Kinetics with the postage prepaid. Underwater Kinetics agrees to repair or replace, at their sole discretion, any product found to be defective in material or workmanship within the time period specified above.
Q: How can I learn more about the warranty?
A: For the complete Limited Lifetime Warranty, please write to Underwater Kinetics or visit their website at www.uwk.com.
Congratulations on the purchase of your Underwater Kinetics Lighthouse work and safety light! This waterproof high high-intensity tilt and swivel LED hand light includes a magnetic base to provide you with maximum versatility for a safe and efficient work environment. The durable design will give you many years of trouble-free lighting.
Technical Data
Technical Data UK4AA eLED
- Batteries: 4x Alkaline AA /LR6/mignon or Energizer AA Ultimate Lithium
- Lamp type: High-Intensity LED
- Size: 8.4 x 2.0 x 1.60 in; 21.4 x 5.1 x 4.1 cm
- Weight: 8.1 oz; 231 g (with batteries and clip)
- Materials: ABS, polycarbonate, copper alloys, stainless steel
- Immersion depth: 10 feet / 3 m
CAUTION
Batteries can vent hydrogen gas and possibly cause an explosion
- if they are installed without the proper polarity,
- if they are not the same type, brand name and age or
- if they are completely discharged.
- Load batteries according to the diagram.
- Discard all batteries as soon as they are drained or no longer produce light.
- Do not mix batteries of different types, brands or ages.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS AND IMPORTANT INFORMATION
-
Battery Installation
To install batteries, hold the case in the position shown. (1) Drop two batteries with the positive + end down into the case. (2) Then drop two batteries with positive + end facing up into the case. Place the Lamp Head over the mouth of the light and twist it onto the case. -
ON/OFF
To operate the light push in on the black rubber switch located on the case near the head to turn the light ON and OFF. -
Tilt & Swivel Lamp Head
The Lamp Head can be tilted up or down 120° and locked into position with the Lock Knob. It can also be rotated from side to side 360° for the best lighting position. -
Spot/Diffuse Beam Selection
Choose between the Spot beam or Wide Angle Diffuse beam by pressing the selector switch button located on the side of the lamp head. Rotate the lamp head to point the beam to the correct position. -
Rubber Padded Magnetic Base
A powerful magnet is located in the base of the Lighthouse so that it can be attached to any steel or magnetic surface. It is not attracted to aluminium, copper or other non-ferrous metals. -
Belt/Pocket Clip
A stainless steel or nylon Belt/Pocket Clip can be snapped onto the side of the Lighthouse. First, insert one side of the clip through the slot on the side of the Case. Then snap the clip around the case as shown in the illustration. -
O-Ring Seal
The O-ring and threads must always be kept clean. Lightly lubricate the O-ring which seals the rubber-covered bezel and case with silicone grease. Pressure Equalizing Vent Air and gas from battery leakage can pass freely in and out of the LightHouse through a black triangle-shaped vent in the side of the light. Do not allow dirt or grease to accumulate on the vent or it will not operate properly.
Care and Maintenance
- Keep the area around the O-ring clean.
- If the light floods, empty it immediately, rinse it with fresh water and dry it completely before assembly
- Do not store batteries in the light for long periods of time when not in use; they may leak and damage the light.
US – Limited Lifetime Warranty
Underwater Kinetics products are engineered for maximum performance and
durability. All products carry a Limited Lifetime Warranty to the original
retail purchaser to be free from defective material and workmanship under
normal and intended use. In addition, the Underwater Kinetics Limited Warranty
covers materials used in its products to the original purchaser, from the date
of purchase, as follows: plastics for 10 years; rubber for 3 years, LED and
electronics for 2 year, rechargeable batteries for 90 days.
In the event the original retail purchaser detects a defect in the material or
workmanship, the product along with proof of purchase date should be returned
to an authorized Underwater Kinetics dealer or directly to Underwater Kinetics
with the postage prepaid. Underwater Kinetics agrees to repair or replace at
Underwater Kinetics’ sole discretion any product found to be defective in
material or workmanship within the time period specified above. For the
complete Limited Lifetime Warranty write to Underwater Kinetics or go to the
website www.uwk.com. Address all correspondence and
returns to:
- Underwater Kinetics, 13400 Danielson Street, Poway, CA 92064
- Tel: 858-513-9100, 800-327-7388;
- e-mail: info@uwk.com;
- web: www.uwk.com;
- e-mail info@uwk.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>