ENVIO AESS-DVM70H800L 4K Lite Varifocal Dome Hybrid Camera User Guide
- June 13, 2024
- ENVIO
Table of Contents
ENVIO AESS-DVM70H800L 4K Lite Varifocal Dome Hybrid Camera
Luna Series | AESS-DVM70H800L
AESS-DVM70H800L
4K Lite Varifocal Dome Hybrid Camera
Main Features Camera
- 1/3CMOS SENSOR 4K Lite (3480×2160)
- 2.8-12mm Varifocal lens
- Maximum IR Led distance 30m
- 4in1 AHD, HD-CVI, HD-TVI, CVBS (UTC)
- 24pcs smd IR LEDs
- IP65
- DC12V
Product Usage Instructions
Warnings & Precautions
Dear Customer, thank you for choosing our product. Correct usage of this
product ensures high-quality and reliable solutions over time. This manual
provides instructions for using the product.
Connections
Make sure the camera is not powered before making connections. The video
cable is connected to the female bayonet BNC connector, which is then
connected to the monitor or DVR via RG59 type coaxial cable and BNC connector.
Twisted pair cables can also be used with balun converters.
Technical Specification
- Image Sensor : 1/3CMOS SENSOR 4K Lite (3480×2160)
- Effective Pixels: 3480×2160
- Scanning System : 1-channel BNC high definition video output
- Minimum Illumination
- IR Distance: Maximum 30m
- IR On/Off Control: Auto (ICR) / Manual
- IR LEDs: 24pcs smd IR LEDs
- Lens : 2.8-12mm Varifocal lens
- Lens Type : Auto / Manual
- Focal Length
- Angle of View
- Focus Control
- Video Resolution
- Video Output: 4in1 AHD, HD-CVI, HD-TVI, CVBS (UTC)
- Day/Night OSD Menu : Multi-language
- BLC Mode : BLC / HLC / WDR
- WDR Gain Control : WDR AGC 3D Auto / Manual
- Noise Reduction: Auto / Manual
- White Balance: Auto / Manual
- Smart IR
Installation
This section indicates how to install the camera on a ceiling or wall with
protected cable passage. Check the solidity of the structure on which you
intend to fix the camera, mark the points with a pencil and drill the
necessary holes for its fastening.
Dome type camera
- Framing adjustment
OSD menu
For the full OSD manual, please visit www.enviosecurity.com.
Main Features Camera
- 1/3”CMOS SENSOR 4K Lite
- (3480×2160)
- 2.8-12mm Varifocal lens
- Maximum IR Led distance 30m
- 4in1 AHD,HD-CVI, HD-TVI, CVBS (UTC)
- 24pcs smd IR LEDs
- IP65
- DC12V
Warnings & Precautions
Dear Customer, we thank you for choosing one of our products whose correct use
guarantees solutions of the highest quality and reliability over time. This
manual provides instructions for using the product.
Connections
Make sure the camera is not powered before making connections.
The video cable is connected to the female bayonet BNC connector, which is
then taken to the monitor or DVR in general via RG59 type coaxial cable and
BNC connector. Twisted pair cables can also be used with balun converters.
Check that the power supply is correct and provided for the camera model used.
The use of adequate power supply units is recommended. 12Vdc / 1A or 12Vdc /
1,5A stabilized is recommended. The pin required is the standard 5.5 mm.
Beware of power extension cables that are too long or have a small section,
which could introduce an excessive voltage drop, especially when the IR
illuminator is turned on.
The values expressed in the following table are to be considered at a
temperature of 20 ° C [68 ° F].
As the copper conductor section increases, there is a decrease in the resistance value () / m) and therefore in the voltage drop on the cable itself. Therefore, consider carefully the length and section of the cable during the design phase. Excessive distances between the power supply and the camera could compromise the correct functioning of the camera. The acceptable standard of variation of the supply voltage is 12Vdc ± 10%
Installation
This section indicates how to install the camera on a ceiling or wall with
protected cable passage.
Check the solidity of the structure on which you intend to fix the camera,
mark the points with a pencil and drill the holes necessary for its fastening.
3 Dome type camera
Dome cameras consist of the camera unit and the fixing base which are screwed
together. Before proceeding with the assembly, the fixing base must be
unscrewed, separating it from the camera body. Generally, no tools are needed
to unscrew the fixing base from the camera body, however, if this is tightened
too deeply, you can help yourself by placing a rigid rod, such as a
screwdriver, between the
two lateral cable outlet slots located in the base. The fixing base, separated
from the camera, is fixed to the wall or to the wall with plugs in
correspondence with the cable outlet hole and the camera body is subsequently
screwed onto it. Before tightening fully, correctly orient the viewing angle.
Framing adjustment
Once correctly fixed to the wall / ceiling, point it in the desired direction
and lock it (it may vary from model to model) by tightening the screws with
the supplied Allen key.
Fixed lens cameras (IR up to 20m) do not require focus as they are factory set
for most applications.
To ensure excellent image quality even in low light conditions, all models are
equipped with a Day & Night function with removal of the IR filter to
automatically switch from color to B / W. In addition, all models are equipped
with integrated 850nm IR LED illuminators, for adequate illumination of the
area being shot. Be careful not to install the camera very close to strong
light sources or in places subject to reflection of light that could
compromise the correct vision of the camera.
OSD menu
Depending on the camera models.
This model has a coaxial control
- Access the DVR menu in the appropriate coaxial configuration section (in ENVIO DVRs this setting is called “XVI control”. Press the central console button that appears on the monitor to enter the menu home page.
- Select topic / function of interest using the scroll up / down buttons.
- Use the left or right buttons to select the different operating modes.
- Move to [EXIT] and press the center button to exit the setting mode, without saving the settings.
- Navigate to [SAVE & EXIT] and press the center button to exit the setting mode, saving the settings.
For the full OSD manual visit www.enviosecurity.com