CURTIS CSP961 2×8.5 Inch Bluetooth Speaker Light Up FM Radio Instruction Manual
- June 4, 2024
- Curtis
Table of Contents
CSP961 2×8.5 Inch Bluetooth Speaker Light Up FM Radio
Instruction Manual
Please read carefully and keep this manual before your use this device.
Caution
This device is not a toy, please keep it away from children.
Keep away from water and extreme temperatures.
Low power may cause poor Bluetooth connection or sound distortion.
Do not overcharge the battery.
Do not disassemble, modify, or repair the device by yourself.
Charge the device
Insert a Micro USB plug into the DC 5V/1A port, then plug another end into the
AC-DC 5V USB adapter, and plug it into one wall socket to charge the device.
The LED indicator will flash in red while charging and turn off when fully
charged.
Specification
Main Function: Bluetooth, AUX, USB, TF, FM Radio, MIC, VOL*3, Screen Display,
Light up.
Speaker Drive:2×8.5″ 15W woofer + 1×1.5″ 5W tweeter
Rated frequency: 2.4G
Power input: DC 5V
Built-In Rechargeable Battery: 3.7V 2500mAh
Signal-to-noise ratio≧75dB
Transmission distance ≧10m
In the Box
2x 8.5 “LIGHT-UP BLUETOOTH SPEAKER-FM RADIO
1 wired microphone
1AUX cable
1Micro USB Cable
1 AC-DC 5V 1A adapter
1*User Manual
Control Panel
Power ON/OFF
Turn the power on, the device will automatically enter pairing mode.
Turn the power switch to the OFF position, the device will be powered off.
Bluetooth Pairing
- Turn power on, the device will automatically enter pairing mode.
- Set your Bluetooth device and keep its Bluetooth function on to search “Curtis CSP961”, select and click and connect to the device.
- Once successfully paired, the prompts will be heard and the indicator will stop flashing.
Connect to the AUX Port
Press the “Mode” key to switch to AUX in Mode, the prompts will broadcast “AUX
IN Mode”, plug an Audio 3.5mm connector into the “AUX IN” port on the device,
then plug another connector into your media playing device.
Play Music
To listen music on the device, make sure it is paired to the Bluetooth-enabled
device or connected well to the auxiliary input port. See the Bluetooth
pairing and connected to the AUX port section of the manual for details.
FM Radio
Press the “MODE” key to switch to FM Radio state, and press and hold.
The device will automatically search for stations, lock channels, and
broadcast news or music.
Press “Prev” and “Next” to switch channels.
Card reading function
Insert the TF card or U disk which stored and recorded the audio files into
the corresponding TF slot or USB port, the device will automatically
recognize, read and play.
TWS Function
- Make sure the two device are POWER ON, NO paired with any Bluetooth device. You will hear prompts to guide you.
- Choose one speaker as your master device.
- Long press the “TWS” key on the master device.
- The two speakers will wirelessly be connected well, and you will hear the prompts Once successfully paired.
LED Lights ON/OFF
Turn on the power switch, the device automatically enters the lighting effect
and adjusts the lighting effect automatically.Users can also press the MODE
button and hold it one second each time to adjust the lighting effect, and
turn the LED lights on or off.
FCC Statement
NOTE: This device has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This device generates uses and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or
television reception, which can be detewrmined by turning the device off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
RePower ON/OFF
Turn the power on, the device will automatically enter pairing mode.
Turn the power switch to the OFF position, the device will be powered off.
Bluetooth Pairing
-
Turn the power on, the device will automatically enter pairing mode.
-
Set your Bluetooth device and keep its Bluetooth function on to search “Curtis CSP961”, select and click and connect to the device.
-
Once successfully paired, the prompts will be heard and the indicator will stop flashing.
Connect to the AUX Port
Press the “Mode” key to switch to AUX in Mode, the prompts will broadcast “AUX IN Mode”, plug an Audio 3.5mm connector into the “AUX IN” port on the device, then plug another connector into your media playing device.
Play Music
To listen to music on the device, make sure it is paired to the Bluetooth-
enabled device or connected well to the auxiliary input port. See the
Bluetooth pairing and connected to the AUX port section of the manual for
details.
FM Radio
Press the “MODE” key to switch to FM Radio state, press and hold.
The device will automatically search for stations, lock channels, and
broadcast news or music.
Press “Prev” and “Next” to switch channels.
Card reading function
Insert the TF card or U disk which stored and recorded the audio files into
the corresponding TF slot or USB port, the device will automatically
recognize, read and play.
TWS Function
- Make sure the two devices are POWER ON, NO paired with any Bluetooth device. You will hear prompts to guide you.
- Choose one speaker as your master device.
- Long press the “TWS” key on the master device.
- The two speakers will wirelessly be connected well, and you will hear the prompts Once successfully paired.
LED Lights ON/OFF
Turn on the power switch, and the device automatically enters the lighting
effect and adjusts the lighting effect automatically.Users can also press the
MODE button and hold it one second each time to adjust the lighting effect,
and turn the LED lights on or off.
FCC Statement
NOTE: This device has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This device generates uses and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or
television reception, which can be determined by turning the device off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the device and receiver.
-
Connect the device to an outlet on a circuit different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
-
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the device. -
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: orient or relocate the receiving antenna.
– Increase the separation between the device and receiver.
– Connect the device into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet the general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.
This symbol signifies that this is a wireless device powered by Bluetooth
technology.
The Bluetooth word mark and Logos are registered trademarks owned by the
Bluetooth SIG. Inc. and any used of such markes by CURTIS is under license.
Customer Support
For any questions or problems with this product, please email
support@curtiscs.com or call 1-800968-9853.
Warranty Information
90-day Warranty
This product is warranted to be free from defects in material and workmanship
for a period of ninety (90) days from the date of original purchase. During
this period, your exclusive remedy is repair or replacement of this product or
component found to be defective, at our option; however, you are responsible
for all costs associated with returning the product to us. If the product or
component is no longer available, we will replace it with a similar one of
equal or greater value. Prior to a replacement being sent, the product must be
rendered inoperable or returned to us.
This warranty does not cover glass, filters, wear from normal use, use not in
conformity with the printed directions., or damage to the product resulting
from accident, alteration, abuse, or misuse.
This warranty extends only to the original consumer purchaser or gift
recipient. Keep the original sales receipt, as proof of purchase, is required
to make a warranty claim. This warranty is void if the product is used for
other than single-family household use or subjected to any voltage and
waveform other than as on the specified rating on the label.
We exclude all claims for special, incidental, and consequential damages
caused by a breach of express or implied warranty. All liability is limited to
the amount of the purchase price. Every implied warranty, including any
statutory warranty or condition of merchantability or fitness for a particular
purpose, is disclaimed except to the extent prohibited by law, in which case
such warranty or condition is limited to the duration of this written
warranty.
This warranty gives you specific legal rights. You may have other legal rights
that vary depending on where you live. Some states or provinces do not allow
limitations on implied warranties or special, incidental, or consequential
damages, so the foregoing limitations may not apply to you.
For faster service, locate the model, type, and serial numbers on your
appliance.
Attach your proof of purchase here, proof of purchase is required to obtain
warranty service.
Please have the following information available when you contact the Support
Team:
Name, address, and telephone number.
The model number and serial number.
A clear, detailed description of the problem.
Proof of purchase including dealer or retailer name, address, and date of
purchase.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in
a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by the manufacturer could void your authority to operate this
equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum
distance of 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>