SAQICO OKQ9 Head Strap Installation Guide

SAQICO OKQ9 Head Strap

Product Information

Specifications:

• Package Includes: 1 Upper head strap frame structure, 1 Lower head strap frame structure, 1 L round buckle, 1 R round buckle, 1 L long strip buckle, 1 R long strip buckle, 8 Large Sponge pads, 9 Small Sponge pads, 1 Top strap pad

Product Usage Instructions

Step 1: Install buckles with arm band

1. Extend the Longest Position.
2. Find the Part 4 L round buckle and Part 6 L long strip buckle.
3. Use Part 1 extend band L hole to fit the 6 L hole. Make sure The L mark of 1 and 6 are upwards.
4. Use the Part 4 L to press on it. Make sure the middle of Part 4 small circular column goes into the hole, and Part 4 feet align with the 4 holes. Also, the Part 4 Gap side should align with part 1 L extend edge. Press hard to insert the 4 feet into the 4 holes.
5. Repeat steps 2-4 for the right section using Part 5 and 7.

Step 2: Install the head strap frame structure

1. Put the part 2 into the up hole of the part 1.
2. Push hard to align with the mark position to the right. Ensure stability without falling off.
3. Use the same way to put the part 3 into the down hole of the part 1.

Step 3: Install with the Sponge Pads

1. Stick the small Sponge Part 9 on the inner surface of Part 2.
2. Stick the large Sponge Part 8 on the inner surface of Part 1.
3. Put the Top strap pad Part 10 through the part 2 hole.

Step 4: Install with your VR Headset

1. Use The Part 100 Top Strap Pad through The VR Headset Top Hole.
2. Use the part 6 to fit into the VR L ear Hold the Side of 6 Position and hard press the other side of 6 until you hear a Click Sound, which means it is installed.
3. Use the same way to install the R side. Adjust the elastic black band and rotate the knob to adjust the headset with your head.

FAQ

Q: How do I remove the buckles if they are mixed up?

A: If the buckles are mixed up, it can be troublesome to remove them. You may need a straight tool to pry the buckles.

Q: What should I do if I pressed the buckles inside and cannot disassemble them?

A: Once the buckles are pressed inside, they cannot be disassembled. Therefore, it is important to make sure all the parts are used correctly and follow the provided guidance.

Q: How do I adjust the headset with my head?

A: Adjust the elastic black band and rotate the knob to achieve a comfortable fit on your head.

Q: Where can I contact customer service?

A: For any problems or inquiries, please feel free to contact us at customerafterservice@gmail.com.

Important Note:

Before installing, be sure to confirm the letters “L” and “R” icons on the buckle and extension arm. Once mixed, it will be troublesome to remove the buckles, and you may need a straight tool to pry the buckles.

Package Include

1. With 360°Round Rotation Knob frame structure
2. Upper head strap frame structure
3. Lower head strap frame structure
4. L round buckle
5. R round buckle
6. L long strip buckle
7. R long strip buckle
8. Large Sponge pads
9. Small Sponge pads
10. Top strap pad

Installations Instruction

Step 1: Install buckles with armband

1. Use the Part 1：Rotate the 360° Round Rotation knob counterclockwise to extend the band to the Longest Position.
2. Find the Part4 round buckle and Part L long strip buckle: as the Picture
3. Use Part extend band 1 “hole” to fit the 6“hole” 1 ,as the Picture Make sure The “6” mark of  and are upwards as the Picture
4. Use the Part “4” to press on it. Make sure the middle of Part  “small circular column” into the hole,and Part 4 feet align with the 4 holes. also Part 4 ” Gap“ side is align with part “4”extend dege Then hard press the 4 feet into the 4 holes. Please pay attention: “You need Press a little hard to press it in. and Once Press inside, It can’t be disassembled. So Please make sure all the Parts used is correct and follow our guidance. especially the “L” and “R”, up or down etc.
5. Find Part 5,7 use the same way as the left “step” to complete the Right Section.

Step 2 Install the head strap frame structure

Step 3 lnstall with the Sponge Pads

1.  Stick the small Sponge “Part 9 on the inner surface of Part 2 ****
2. Stick the large Sponge “Part ” 8 on the inner surface of Part 1
3. Put the Top strap pad “Part “10 through the part hole 2

Step 4 Install with your VR Headset

1. Use The Part 10″ Top Strap Pad through The VR Headset Top “ Hole”
2. Use the part 6 fit into the VR L “ear” Hold the Side of Postion and hard press the other side of Until  heard a “Click “Sound means it is installed.
3. Use the same way install the “R” side . adjust the elastic black band and rotate the knob to adjust the headset with your head.

Customer Service

Saqico is devoted to providing you high quality products for more comfortable and immersive gaming experience wandering in the VR world. If you have any problems, please feel free to contact us.

• E-mail: customerafterservice@gmail.com

Please Scan the right QR Code for get Video installations

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>