L S 2036 Remote Controller User Manual
- June 16, 2024
- L S
Table of Contents
2036 Remote Controller
User Manual
2036 Remote Controller
-
remote control button function
Note: short press the corresponding number to select the group to be controlled for example short press“1“，that means “group 1”is to be controlled, all subsequent operations are for the group selected last time
Reset：long press“off” button for 5s, LED light indicator blinks in red for 60S, if no other operations LED light indicator turn off，enter low power mode. To work again, repeat the above steps -
controller button function
(1) Input 24V power off, CCT/single CCT dip switch to select
(2) Reset: long Press”Reset” button for 5s -
button press instruction
(1) Short press, press time＜1s
(2) Long press，press time ＞5s -
device working through the Hue gateway instruction
Note the remote controller can’t show on the Hue App（The buttons on the remote control are customization defined）
(1) Join ZigBee network
1）remote join Hue gateway
Step 2: Open the Hue APP and click Add Device
(remote controller) to enter the pairing modeler light indicator stop flicker
in relight up in green and then light off that indicate pairing successfully
if not successful repeat the operation.
- Controller join Hue gateway
Method one：
Step2: Open
the Hue APP and click Add Device，APP will show the device if pairing
successfully or repeat the operation
Method two：
Open HUE APP，enter the 6 digitals on the controller to pair directly，APP will show the device if pairing successfully or repeat the operation
(2) Add
group and delete group instruction
1）controller adding group
2）delete group
a. delete one of the device in the group
b. delete all the device at the remote controller group
pairing through Touchline
(1) Join ZigBee network and group
Step1: reset the remote controller,
Step2: Make the distance between the remote controller and the device
(controller and LED strip) less than 15cm
(2) Exit ZigBee network and group
Step1: Make the distance between the remote controller and the device
(controller and LED strip) less than 15cm。
connect RC to ZigBee controller Sun richer type SR-ZG1029 through Touch
link
Step2: long press off button on remote controller to reset and the indicator light will flicker in red
Step4: make
the distance between the remote controller and the device (controller and LED
strip) less than 15cm
FCC Statement
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Supplier’s Declaration of Conformity
Product Name：Remote Controller
Model number： RR-CONTROL-EASYLUX-1+4-CH, Remote control 4-chan
Suppliers Name: VISHTEC LLC
Suppliers Address (USA) ：9888 W Belleview Ave Ste 2142 Denver CO 80123
Suppliers Website: N/A
Contact Email/Telephone: Alan.graham@vish-tec.com /（571）4007350
FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>