ASSA ABLOY PCBA1731C1 Zigbee Module PCBA 1731 User Guide

ASSA ABLOY PCBA1731C1 Zigbee Module PCBA 1731

Specifications

• Model: Zigbee Module PCBA 1731
• Copyrights: The information in this document is subject to change at the sole discretion of ASSA ABLOY without notice. Any use, operation or repair in contravention of this document is at your own risk. ASSA ABLOY does not assume any responsibility for incidental or consequential damages arising from the use of this manual. All information and drawings in this document are theproperty of ASSA ABLOY. Unauthorized use and reproduction isprohibited.
• FCC Statements:
  • This device complies with part 15 of the FCC Rules.
  • Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that maycause undesired operation.
  • Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  • This device complies with FCC rule CFR 47, Part 15, Subpart C, paragraph 15.247, operating within the band 2400-2483.5 MHz, Digital transmission systems.
  • The final host product manufactured by ASSA ABLOY Global Solutions Norway AS and not covered by the modular transmitter grant of certification, with a PCBA 1731 installed, may also need to pass the FCC rule CFR 47, Part 15, Subpart B, unintentional emission testing requirements.
  • Labels: The Zigbee module, model PCBA 1731, must be labeled to say FCC ID: Y7V-PCBA1731C1. The concerned end product must be labeled to say Contains FCC ID: Y7V-PCBA1731C1.
• ISED Statements:
  • This device complies with Industry Canada license-exempt RSS standard CAN ICES-3 (B)/NMB-3(B) B.
  • Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must acceptany interference, including interference that may cause undesired operation of the device.
  • Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
  • To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
  • The radio transmitter IC: 9514A-PCBA1731C1 has been approved by Industry Canada to operate with the antenna type listed below with the indicated maximum permissible gain and required antenna impedance.
  • Name/Model: Inverted F antenna
  • Gain: 2.0 dB
  • Impedance: 50 ohm
  • The term IC before the equipment certification number only signifies that the Industry Canada technical specifications were met.
  • The Zigbee module, model PCBA 1731, must be labeled to say IC: 9514A-PCBA1731C1. The concerned end product must be labeled to say Contains IC: 9514A-PCBA1731C1.

Product Usage Instructions

FCC Compliance

To ensure FCC compliance when using the Zigbee Module PCBA 1731, please follow these instructions:

1. Do not make any changes or modifications to the device that are not expressly approved by the responsible party for compliance.
2. Ensure that the device operates within the frequency band of 2400-2483.5 MHz.
3. Label the Zigbee module with FCC ID: Y7V-PCBA1731C1.
4. Label the concerned end product with Contains FCC ID: Y7V-PCBA1731C1.
5. If the final host product manufactured by ASSA ABLOY Global Solutions Norway AS and equipped with PCBA 1731 is not covered by the modular transmitter grant of certification, it may need to pass unintentional emission testing requirements as per FCC rule CFR 47, Part 15, Subpart B.

ISED Compliance

To ensure ISED compliance when using the Zigbee Module PCBA 1731, please follow these instructions:

1. Ensure that the device operates within the Industry Canada license-exempt RSS standard CAN ICES-3 (B)/NMB-3(B) B.
2. Do not cause interference to other devices and accept any interference received.
3. Use an antenna of a type and maximum gain approved for the transmitter by Industry Canada.
4. Choose an antenna type and gain that does not exceed the necessary power for successful communication to reduce radio interference to other users.
5. Label the Zigbee module with IC: 9514A-PCBA1731C1.
6. Label the concerned end product with Contains IC: 9514A-PCBA1731C1.

FAQ

• Q: What should I do if I encounter interference while using the Zigbee Module PCBA 1731?
  A: If you encounter interference, ensure that the device accepts any interference received. You may also try adjusting the antenna type or gain to reduce potential radio interference.

• Q: Can I modify the Zigbee Module PCBA 1731?
  A: No, any changes or modifications to the device that are not expressly approved by the responsible party for compliance may void your authority to operate the equipment.

• Q: What labels should be applied to the Zigbee module and the end product?
  A: The Zigbee module should be labeled with FCC ID: Y7V-PCBA1731C1 and IC: 9514A-PCBA1731C1. The concerned end product should be labeled to say Contains FCC ID: Y7V-PCBA1731C1 and Contains IC: 9514A-PCBA1731C1.

Copyrights

• The information in this document is subject to change at the sole discretion of ASSA ABLOY without notice.
• Any use, operation or repair in contravention of this document is at your own risk. ASSA ABLOY does not assume any responsibility for incidental or consequential damages arising from the use of this manual.
• All information and drawings in this document are the property of ASSA ABLOY. Unauthorized use and reproduction is prohibited.

FCC and ISED statements

FCC statements
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Caution : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note : This device complies with FCC rule CFR 47, Part 15, Subpart C, paragraph 15.247, operating within the band 2400-2483.5 MHz, Digital transmission systems. Test performed in accordance with ANCI C63.4-2014 and ANSI C63.10-2013.
The final host product manufactured by ASSA ABLOY Global Solutions Norway AS and not covered by the modular transmitter grant of certification, with a PCBA 1731 installed, may also need to pass the FCC rule
CFR 47, Part 15, Subpart B, unintentional emission testing requirements.

Exposure statement:
This portable device with its antenna complies with FCC RF exposure limits for general population/uncontrolled exposure. The antenna used for this device must not be co-located or operating in conjunction with any other antenna or transmitter. Use only the supplied antenna. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antennas or transmitters.

Labels:

• The Zigbee module, model PCBA 1731, must be labeled to say FCC ID: Y7V-PCBA1731C1.
• The concerned end product must be labeled to say Contains FCC ID: Y7V-PCBA1731C1.

ISED statements

This device complies with Industry Canada licence-exempt RSS standard CAN ICES-3 (B)/NMB-3(B) B. Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
The radio transmitter IC: 9514A-PCBA1731C1 has been approved by Industry Canada to operate with the antenna type listed below with the indicated maximum permissible gain and required antenna impedance. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

• The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.
• The Zigbee module, model PCBA 1731, must be labeled to say IC: 9514A-PCBA1731C1.
• The concerned end product must be labeled to say Contains IC: 9514A-PCBA1731C1.

Overview

This document is a quick reference guide for the Zigbee module manufactured by ASSA ABLOY Global Solutions, model PCBA 1731.
The electronic module consists of a PCB and its components.

• Mass: 7.2 g
• Dimensions (W x D x H): 61.8 x 35.5 x 6.5 mm.

1. To be operating, PCBA 1731 must be mounted on an ASSA ABLOY Global Solutions electronic lock that works as a host system. The six-pin connector allows data communication with the lock and provides power supply from the lock. Several types of ASSA ABLOY Global Solutions electronic locks are compatible with the module.
2. Power supply: 4.5VDC battery pack located inside the lock
3. The main purpose of PCBA 1731 is to establish wireless communication with a Zigbee network to exchange data e.g. in the hospitality industry.
4. The exchange of information is via radio by an integral 2.4GHz PCB antenna, using Zigbee protocol to either a router or a gateway; both router and gateway can be a third-party equipment. The PCBA 1731 is compatible with a cloud-based service.

The ASSA ABLOY Group is the global leader in access solutions. Every day we help people feel safe, secure and experience a more open world.
ASSA ABLOY Global Solutions APAC
apac.globalsolutions@assaabloy.com
Phone : +852 23162200
ASSA ABLOY Global Solutions EMEA
emea.globalsolutions@assaabloy.com
Phone : +47 69 24 50 00
ASSA ABLOY Global Solutions North America
nam.globalsolutions@assaabloy.com
Phone : +1 972 907 2273
ASSA ABLOY Global Solutions Latin America
lac.globalsolutions@assaabloy.com
Phone : +52 55 36 40 12 00
assaabloyglobalsolutions.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>