FITHRILL FT-SE02 Walking Pad Under Desk Treadmill User Manual

FITHRILL FT-SE02 Walking Pad Under Desk Treadmill

IMPORTANT: Read all instructions carefully before using this product. Retain this owner’s manual for future reference. Your satisfaction is very important to us, any questions PLEASE CONTACT US: Fithrill- service@outlook.com

CUSTOMER SERVICE

Please let us know if you have any issues or concerns with the transaction. shipping or product. And relevant photos or videos are very important to help us better understand the problem. We’ll do our best to make it right for you!

Email Address: Fithrill-service@outlook.com

• Contact us via Amazon:  Log in to your Amazon account
• choose “Your orders”
• find the order ID
• click “Contact Seller”

Or

• Click our store “Seller name” Under the Buy Box
• Click “Ask a question”
• Click “An order I placed”
• Select a subject and write a message to us

IMPORTANT SAFETY INSTRUCTIONS

DANGER – To reduce the risk of electric shock:

1. Always unplug this treadmill from the electrical outlet immediately after using and before cleaning.

WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1. A treadmill should never be left unattended or plugged in. Unplug from outlet when not in use, and before putting on or taking off parts.
2. Do not operate under a blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.
3. Close supervision is necessary when this treadmill is used by, on, or near children, invalids, or disabled persons.
4. Use this treadmill only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
5. Never operate this treadmill if it has a damaged cord or plug if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the treadmill to a service center for examination and repair.
6. Do not carry this treadmill by supply cord or use cord as a handle.
7. Keep the cord away from heated surfaces.
8. Never operate the treadmill with the air openings blocked. Keep the air openings free of lint, hair, and the like.
9. Never drop or insert any object into any opening.
10. Do not use outdoors.
11. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
12. Caution – To reduce the risk of injury from moving parts – Unplug before servicing.
13. Warning – To reduce the risk of Electricshock – Unplug before cleaning or servicing.
14. Warning – Risk of personal injury – Keep children under the age of 13 away from the machine.
15. To disconnect, turn all controls to the position, then remove the plug from the outlet.
16. Connect this treadmill to a proper outlet only. See grounding instructions.
17. This treadmill is not intended for use by persons with reduces physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the treadmill by a person responsible for their safety. Keep children under the age of 13 away from this machine.
18. The maximum weight capacity for this product is 265 lbs/120 kg. DO NOT EXCEED MAXIMUM WEIGHT CAPACITY.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electricity and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded per all local codes and ordinances.

DANGER – Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product – if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

PRODUCT & ACCESSORIES

Please carefully check whether the contents of the package are complete and intact. If there is any missing or damage, please contact the seller.

Accessories

SPECIFICATION

Product Configuration| Detailed parameters| Product Configuration| Detailed parameters
---|---|---|---
Product dimension (Folded down)|

1260x560x 155 mm

|

Product dimension (Folded up)

|

1202x560x1050 mm

49.6x22x6.1 inch

|

47.3x22x41.3 inch

Running area

|

400×1000 mm

|

Maximum speed

|

7.6 mph

15.7×39.4 inch

Gross weight

|

24 KG

|

Minimum speed

|

0.6 mph

52.9 Lbs

Net weight

|

20.6 KG

|

Rate voltage

|

110 -120V ~

45.4 Lbs

Maximum load

|

120 KG

|

Peak horsepower

|

2.5 Hp

300 Lbs|

Suggested age

|

14-60 years old

PRODUCT INTRODUCTION

HOW TO USE

Unfolded To Run (Speed range: 0.6- 7.6 mph)

1. Unbox to take out the treadmill with the related accessories, then place the treadmill on flat ground.
2. Rotate the handrail switch out in the direction shown in the figure and place it aside, with the same operation on both sides.
3. Lift the handrail as shown in the figure, aligning the handrail clamp iron with the bottom frame bolt hole.
4. Lock the handrail switch into the alignment hole, and operate the same left and right.
5. Insert tablet mount refer to arrow sign.
6. Plug in the power cord to the power connector.
7. Power on and start running.
8. Note: Before use, it is necessary to install the battery in the accessory package into the lower battery slot of the handrail. As shown in the figure, open the battery cover and press the positive and negative positions to install the battery.

Folded To Walk (Speed range: 0.6 – 4.0mph)

1. Detach the tablet mount.
2. Fold down hand I bar subassembly under the reverse procedure.
3. Enjoy walking exercises with a remote control.

Note: To enhance the customer’s incline experience, this treadmill has a manual incline component, as shown in the figure. When the component is opened, the incline is 1.5 degrees and the height is increased by 28mm .

Safety Key
In any emergency occurs, the treadmill stops automatically and shows” —” when the safety key is pulled out from the console.

NOTE: Find the clip (A) onto the waistband of your clothes, and another key (B)magnetic attracted under the console.

Transportation

1. If transportation is needed, please unplug the power cord and tablet mount before lifting the terminal of the treadmill
2. Easy to transport treadmill with bottom transportation wheel assists, like a wheelbarrow.

NOTE: Before moving and storage, please make sure the power switch into off and the power cord is unplugged.

OPERATION

Console

Touch button feature

Standby Mode
If the pause time is over 10 minutes, it will switch to “standby mode” automatically. In standby mode, not only console light off but also previous workout datas will be erased to Zero, you can weak up the console by touching any button.

Display Screen

As you walk on or run on the treadmill, the display can show the following workout information:

burned.

Time| 00 -99 minutes| Displays the elapsed time.
Distance| 00.00- 99.99 miles| Displays the distance that you have walked or run.

Note: Autonomy is 99 minutes. You have to re-start treadmill, in case your exercise time is over 99 minutes, and previous workout data will be erased and recounted accordingly.

Remote Control

FUNCTIONS OF THE REMOTE CONTROL KEY

CARE & MAINTENANCE

Symptom : walk belt off centered or slips.

The centering walk belt process is as follows:

1. Power off the treadmill and unplug the power cord.
2. The manual centering process is as follows:
   • If the walking belt has shifted to the left, use the hex tool to turn the left idler roller screw clockwise 1/4 of a turn(refer to Figure 1 ).
   • If the walking belt has shifted to the right, use the hex tool to turn the right idler roller screw clockwise 1/4 of turn(refer to figure 2).
3. Treadmill MUST work for 1-2 minutes. Repeat the manual centering process until the walking belt is centered.

The belt slip-correcting process is as follows:

1. Power off the treadmill before operation.
2. Using the hex tool, turn both idler roller screws clockwise 1/2 of the turn(refer to Figure 3).
3. After correcting, please attempt to walk 1-2 minutes under a 2-3mph speed setting. Repeat until the walking belt is properly tightened.

Note: The Tread-belt should not be adjusted too tightly, otherwise it will be damaged.

Attention

1. To prevent any injury, don’t place any debris around the treadmill before the maintenance process.
2. MUST use the associated hex tool.
3. Take care of the maintenance process. Do not pinch your fingers.

Belt lubrication process, follow the instructions below to lubricate the belt.

1. Power off the treadmill and unplug the power cord.

2. Using the hex tool, turn both idler roller screws counterclockwise till the belt loosens and lifts easily.
   Tips: Please  mark hex tool rotating cycles when loosening the belt, which is used for adapting belt tension after the lubrication process.

3. Lifting the edges of the belt and spraying lubrication oil at the center of the walking platform evenly. Not necessary to apply spray lubrication oil on the entire walk platform.

4. Lubrication oil volume Per time of maintenance: 5- 10ml.
   Attention: it would cause the belt to slip if sprayed too much.

5. Using the hex tool, turn both idler screws clockwise as previous markdown number of turns until the walking belt tightens properly.

6. Power on the treadmill and work out for a few minutes, to spread lubrication oil to the whole belt surface evenly.
   Attention: please hold the handrail when working at 4mph. Lubrication frequency: High recommend 100 Miles Per time.

Treadmill cleaning

1. Power off the treadmill and unplug the power cord before cleaning.
2. Wipe and clean with a damp cloth, Do not clean with acidic or caustic detergents.
3. Do not clean the opposite of the walk belt.
4. Its normal few black powders are residual under the treadmill after a long working.

ERROR CODE

E01

| ****

Communication was interrupted between the controller and the numeric display.

| Unscrew the motor hood and verify the connection between the controller and the numeric display.

Please contact after-sale service if the E01 code has not been eliminated.

Notice: Always power off and unplug the power cord before processing.

E02

| ****

Flame protection

| 1. Unscrew the motor hood and verify the connection between the controller and the motor.

2. Power supply interrupt due to connector loosening or out, please unscrew the motor hood to check.

3. Please contact after-sale service if the problem CAN NOT solved by the above process.

EOS

| ****

Over current protection

| 1. Due to user over limited 120Kg.

2. Open to check any foreign objects blocking moving parts. ( such as drive motor, idler roller, driver roller, walking belt)

3. The walking belt is overtightened or lacks lubricant. ( please see detailed chapters relate to belt tension and lubricant process)

E06

E07| Software bug| Replace the new controller.

E10

| ****

Communication was interrupted between the signal cable and the console.

| 1. Unscrew the console box and verify the connection between the signal cable and the console.

2. Unscrew the console box and verify internal lead wires whether are damaged or pierced.

3. Replace the new console PCBA board.

IMPORTANT: If an error code appears, you MUST stop the workout immediately, Please contact after-sale service if the problem CAN NOT be solved after the restart.

TROUBLESHOOTING

No working

| 1. Power rock switch dyfunction.

2. Power supply interrupted.

3. Power cord damaged.

| 1. Replace the new power rock switch if it doesn’t light on.

2. Make sure that the power cord is plugged into a properly grounded outlet.

3. Replace the new power cable.

Walking belt slips

| ****

A walking belt soothe sen

| Tighten walking belt tension with the hex tool

( 1/4 a turn both idler roller screw clockwise)

The remote control does not work

| ****

1. Incorrect use of default.

2. Battery power shortage.

3. Remote control malfunction.

| ****

1. Remotor control should directly aiming to receiver port when in use.

2. Replace new battery cells.

3. Replace new remote control.

Friction noise| ****

Walking belt off center.

| ****

See details of the walking belt tension chapter.

WARRANTY

MANUFACTURER’S LIMITED WARRANTY
FITHRILL warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated by FITHRILL Owner’s Manual. FITHRILL’S obligation under this warranty applies to the following:

COMPONENT LENGTH OF WARRANTY
Structural Frame 1 year For Home Use Only. All Other Components are 90 days For Home Use Only.

Exclusions from Warranty Coverage:
FITHRILL does not warrant against and is not responsible for, and no implied warranty shall be deemed to cover, any product failure, product malfunction, or damages attributable to:

1. Improper installation and/or failure to abide by FITHRILL’s installation guidelines;
2. Use of this product beyond normal home use, or in an application for which it wasn’t designed;
3. Cosmetic items such as scratches, dents or discolorations;
4. Damage caused by normal wear and tear, vandalism, accidental or by animals;
5. Any act of Nature (such as fire, flooding, snow, ice, hurricanes, earthquakes, lightning other natural disasters), environmental condition (such as air pollution, mold, mildew. etc.), or staining from foreign substances (such as dirt, grease, oil, etc.);
6. Normal weathering is due to exposure to sunlight, weather, and atmosphere which can cause colored surfaces to among other things, flake, chalk, and accumulate dirt or stains.
7. Improper operation, alteration, handling, storage, abuse, or neglect of the products.

FITHRILL, using its sole discretion, will either repair or replace free of charge any part(s) proven to be defective under normal home use, Any repair or replacement shall provide no new warranty coverage, but shall retain only the remaining portion of the original product’s warranty. This warranty is offered only to the original purchaser and is not transferable. Proof of original purchase is required.

When ordering replacement parts please have the following information ready:

1. Order Number
2. Description of Parts(Adding photos or videos would be helpful)
3. Part Number
4. Date of Purchase

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>