KODA 57A 093 860 Set For Spare Wheel Instruction Manual

: June 16, 2024
: KODA

Table of Contents

SET FOR SPARE WHEEL
- Fitting instructions
  - Spare wheel set
- References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SET FOR SPARE WHEEL

Fitting instructions

Order Number
57A 093 860

KAROQ (NU)

[1] 57A 093 860

The spare wheel is not included in the kit. You can order it from the SKODA Genuine Accessories assortment range using order no. 57A 601 011A.

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

Spare wheel set

The spare wheel set 57A 093 860 is intended for SKODA KAROO vehicles with 4×2 front-wheel drive with basic luggage compartment floor and stand-ard (i.e. fixed) rear seats as part of the equipment specification.

The spare wheel (H) itself is not included in the set. This must be ordered from the SKODA Genuine Accessories range using order no. 57A 601 011A.

Component index for the set for spare wheel:

Component|

Quantity

|

Item

---|---|---
Polystyrene box|

1

|

A

Plastic nut|

1

|

B

Fastening bolt with knob|

1

|

C

Luggage compartment floor pin|

1

|

D

Car jack|

1

|

E

Car jack crank handle|

1

|

F

Wheel brace|

1

|

G

Fitting instructions|

1

|

Brief description of how to insert the spare wheel and the polystyrene toolbox into the spare wheel recess in the luggage compartment floor (see figures).

Fig. 2 – Remove the existing luggage-compartment floor covering from the vehicle.
Fig. 3 – Unscrew the plastic nuts at the front of the toolbox (see arrow 1). Remove the existing toolbox from the luggage compartment (see arrow 2).
Fig. 4 – Insert the polystyrene box in the spare wheel recess (in the position shown in the figure) such that the bolts welded to the vehicle floor protrude through the holes in the polystyrene box. Secure the box using the plastic nuts (the plastic nuts that were removed (see arrow) and the plastic nuts (B) from the set).
Fig. 5 – Insert the spare wheel (H) into the spare wheel recess in the vehicle’s luggage compartment, with the outside of the wheel facing down- wards.
Fig. 6 – Insert the fastening bolt with knob (C) into the opening in the spare wheel recess. Push the bolt in and turn it 90° clockwise.
Fig. 7 – Screw on the knob as far as it will go and tighten it. Then insert the luggage compartment floor pin (D) into the fastening bolt.
Fig. 8 – Wheel secured correctly using the luggage compartment floor pin.
Fig. 9 – Remove the towing lug, the tool for removing the wheel covers, the plastic clip for wheel bolt cover caps and other components (depend-ing on the equipment specification, e.g. attachment for anti-theft wheel bolts, light bulbs, etc.) from the existing box.
Fig. 10 – Place the car jack crank handle (F), the car jack (E), the wheel brace (G) and the other components removed from the existing box into the polystyrene box. If there is no space available in the polystyrene box for the light bulb case, this can be stowed in the netting system or in the storage compartment on the luggage compartment side panelling.
Fig. 11- Fit the existing floor covering back into the vehicle’s luggage compartment.

The vehicle’s Owner’s Manual describes in detail how to use the spare wheel and how to replace a wheel in the event of a puncture.

The information on the technical data, design, equipment, materials, guarantees and outside appearance refer to the period when the mounting instructions are sent to print. The manufacturer reserves the right to changes (including the change in technical parameters with reference to the individual model measures).

Nr. 57A 093 860/ 03.2018

www.skoda-auto.com
www.skoda-auto.cz