SEALEY 20230913 Rip Claw Hammer Instruction Manual

SEALEY 20230913 Rip Claw Hammer

Product Information

Specifications

• Manufacturer: Sealey
• Product Type: Hammers
• High-quality manufacturing

General Safety
Before using the hammer, it is important to perform a risk assessment. Ensure that the work area is clean and well lit. Always wear appropriate clothing, eye protection, and footwear while using the hammer. Depending on the task at hand, additional personal protective equipment (PPE) may be required. Do not use the product if you are tired or under the influence of drugs, alcohol, or medication.

Hammer Types

pulling
nails, and prying.
Ball-pein hammer| Has a round, domed face on one end and a ball-shaped pein on
the other end.| Used for forging metal, shaping sheet metal, and riveting.
Deadblow hammer| Has a solid metal head that is filled with lead or another
heavy material.| Used for striking without damaging the surface being
struck.
Framing hammer| Has a long handle and a large, heavy head.| Used for framing walls and other construction tasks.
Mallet| Has a large, smooth head made of wood, rubber, or plastic.| Used for tasks that require a soft strike, such as driving
chisels or shaping wood.
Sledgehammer| Has a very large, heavy head.| Used for demolition and other heavy-duty tasks.
Tapered pin hammer| Has a tapered, pointed head.| Used for driving tapered pins and other small objects.

Usage Instructions

• Wear Safety Goggles
  Always wear safety goggles when using a hammer, especially when hammering hard materials or in circumstances where materials are likely to chip and fly.

• Striking Tools
  When striking chisels, punches, wedges, or other tools, ensure that the striking face of the hammer is larger than the head of the tool being struck. For example, if using a 12mm cold chisel-head, use a hammer with at least a 25mm face.

• Masonry Nails
  Masonry nails, which are hardened, should only be struck with a lump or club hammer. It is essential to wear safety goggles when driving these nails.

• Striking Technique
  Always strike squarely and avoid glancing blows. Do not strike with the side cheek of the hammer head and never strike a material that is harder than the hammer head. Never strike two hammer head faces together.

• Inspect Before Use
  Never use a hammer with a loose or damaged handle. Discard any hammer if the head shows any signs of excessive wear, mushrooming, chipping, dents, etc. Refurbishing hammer faces is not recommended. Light hammers should be used with caution.

FAQ

• Q: Can I use a claw hammer for metalworking tasks?
  A: Claw hammers are primarily designed for general carpentry tasks such as nailing, pulling nails, and prying. For metalworking tasks, it is recommended to use a ball-pein hammer or other suitable hammer types.

• Q: Do I need to wear additional personal protective equipment (PPE) while using a hammer?
  A: Depending on the task at hand, additional PPE may be required. It is important to assess the risks and ensure proper protection by wearing appropriate clothing, eye protection, footwear, and any other necessary equipment.

• Q: How often should I inspect my hammer?
  A: It is recommended to inspect the hammer before each use. Check for any loose or damaged handles, excessive wear on the head, mushrooming, chipping, dents, or any other signs of damage. If any issues are found, do not use the hammer and consider replacing it.

GUIDANCE ON THE SAFE USE OF HAMMERS

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

• GENERAL SAFETY
  • Perform a risk assessment before using the hammer. Ensure the area is clean and well lit. Always wear appropriate clothing, eye protection and footwear when using a hammer.
  • Additional PPE may be required depending on the task at hand. DO NOT use this product if you are tired or under the influence of drugs, alcohol or medication.
• HAMMER TYPE
  Always select a suitable hammer, of the appropriate type, size and weight, for the job concerned. See table below.

pulling nails, and prying.
Ball-pein hammer| Has a round, domed face on one end and a ball- shaped pein on the other end.| Used for forging metal, shaping sheet metal, and riveting.
Deadblow hammer| Has a solid metal head that is filled with lead or

another heavy material.

| Used for striking without damaging the surface being struck.
Framing hammer| Has a long handle and a large, heavy head.| Used for framing walls and other construction tasks.
Mallet| Has a large, smooth head made of wood, rubber, or plastic.| Used for tasks that require a soft strike, such as driving chisels or shaping wood.
Sledgehammer| Has a very large, heavy head.| Used for demolition and other heavy-duty tasks.
Tapered pin hammer| Has a tapered, pointed head.| Used for driving tapered pins and other small objects.

• WEAR SAFETY GOGGLES
  Always wear safety goggles when using a hammer. This is especially important when hammering hard materials and in circumstances where materials are likely to chip and fly.

• STRIKING TOOLS
  When striking chisels, punches, wedges, or other tools, the striking-face of the hammer should be larger than the head of the tool being struck. For example, a 12mm cold chisel-head requires at least a 25mm hammer face.

• MASONRY NAILS
  Masonry nails, which are hardened, should only be struck with a lump or club hammer. It is essential that safety goggles are worn when driving these nails.

• STRIKING TECHNIQUE
  Always strike squarely and avoid glancing blows. Never strike with the side cheek of a hammer head and never strike a material which is harder than the hammer head. Never strike two hammer head faces together.

• INSPECT BEFORE USE
  Never use a hammer with a loose or damaged handle and discard any hammer if the head shows any sign of excessive wear, mushrooming, chipping, dents, etc. Never attempt to refurbish hammer faces. Attention is drawn to the use of light hammers with elongated heads, such as the welder’s chipping hammer, since, whilst handle tests and assembly are appropriate to the mass of the tool, the mode of use can be particularly prone to loosening of handles.

• STORAGE – WOODEN HAMMERS ONLY
  Always store wooden handled hammers at ambient temperatures. DO NOT store in a heated warehouse or storage place as this is a significant cause of loose hammer heads, due to the drying out of the wooden handles.

• INSPECT REGULARLY
  Inspect hammers regularly to ensure they are fit for purpose. If in doubt, seek specialist advise or contact the manufacturer.

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

• Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
• Important: No Liability is accepted for incorrect use of this product.

Warranty

Guarantee is 12 months from purchase date, proof of which is required for any claim.

• Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
• 01284 757500 sales@sealey.co.uk    www.sealey.co.uk
• © Jack Sealey Limited
• Hammers Issue 2 13/09/23

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>