Indesit WIA 101 Washing Machine Instructions Manual

Indesit WIA 101 Washing Machine

• Keep this instruction manual in a safe place for  future reference. Should the appliance be sold,  transferred or moved, make sure the instruction  manual accompanies the washing machine to inform  the new owner as to its operation and features.
• Read these instructions carefully: they contain vital information on installation, use and safety.

Unpacking and levelling

Unpacking

Unpack the washing machine

• Check whether the washing machine has been  damaged during transport. If this is the case, do not install it and contact your retailer.
• Remove the 3  protective screws and  the rubber washer with the respective spacer, situated on the rear of  the appliance (see figure).
• Seal the gaps using the plastic plugs provided.
• Keep all the parts: you will need them again if the washing machine needs to be moved to another location.
  • Packaging materials are not children’s toys.

Levelling

1. Install the washing machine on a flat sturdy floor, without resting it up against walls, furniture cabinets or other.
2. If the floor is not perfectly level, compen- sate for any unevenness by tightening or  loosening the adjustable front feet (see figure);  the angle of inclination,  measured according to  the worktop, must not exceed 2°.
3. Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the washing machine.

Electric and water connections

Connecting the water inlet hose

• Insert seal A into the end of the inlet hose  and screw the latter onto a cold water tap  with a 3/4 gas threaded  mouth (see figure).
• Before making the connection, allow the water to run freely until it is perfectly clear.
• Connect the other end  of the water inlet hose to the washing machine,  screwing it onto the appliance’s cold water  inlet, situated on the top  right-hand side on the  rear of the appliance (see figure).
• Make sure there are no kinks or bends in the hose.
  • The water pressure at the tap must be within the  values indicated in the Technical details table (on the next page).
  • If the water inlet hose is not long enough, contact a specialist store or an authorised serviceman.

Connecting the drain hose 65 – 100 cm

• Connect the drain hose, without bending it, to a  draining duct or a wall drain situated between 65 and 100 cm from the floor;
• alternatively, place it over the edge of a  basin, sink or tub, fastening the duct supplied to the tap (see figure). The free end of the hose should not be underwater.
• We advise against the use of hose extensions; in case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.

Electric connection

• Before plugging the appliance into the mains  socket, make sure that:
  • the socket is earthed and in compliance with the  applicable law;
  • the socket is able to sustain the appliance’s  maximum power load indicated in the Technical details table (on the right);
  • the supply voltage is included within the values i ndicated on the Technical details table  (on the right);
• Do not use extensions or multiple sockets.
• The power supply cable must never be bent or  dangerously compressed.
• The power supply cable must only be replaced by an authorised serviceman.
  • Warning! The company denies all liability if and when  these norms are not respected.

The first wash cycle

Once the appliance has been installed, and beforeyou use it for the first time, run a wash cycle with detergent and no laundry, setting the 90°C programme without a pre-wash cycle.

Technical Details

• Model: WIA 101
• Dimensions: 59.5 cm wide x 85 cm high x 52.5 cm deep
• Capacity: from 1 to 5 kg
• Electric Connections:
  • Voltage: 220/230 Volts 50 Hz
  • Maximum Absorbed Power: 1850 W
• Water Connections:
  • Maximum Pressure: 1 MPa (10 bar)
  • Minimum Pressure: 0.05 MPa (0.5 bar)
  • Drum Capacity: 40 litres
• Spin Speed: Up to 1000 rpm

Control:

• Programmes According to IEC456 Directive:
  • Programme 3
  • Temperature: 60°C
  • Run with a load of 5 kg.

Compliance:

• This appliance is compliant with the following European Community Directives:
  • 73/23/CEE of 19/02/73 (Low Voltage) and subsequent amendments
  • 89/336/CEE of 03/05/89 (Electromagnetic Compatibility) and subsequent amendments
  • 2002/96/CE

Washing machine description

• Detergent dispenser: to add detergent and fabric softener (see page 8).
• LEDS: to find out which wash cycle phase is under way.
• FUNCTION buttons: to select the functions  available. The button corresponding to the function selected will remain on.
• TEMPERATURE knob: to set the temperature or the cold wash cycle (see page 7).
• DOOR LOCK Led: to find out whether the washing  machine is on and if the appliance door can be  opened (see page 5).
• START/PAUSE button: starts or temporarily interrupts programmes.

N.B.: once the programme has started, pressing this button will stop the cycle and only the LED for the cycle phase in progress will light up. After about 1 minute you will be able to open the door when the DOOR LOCK led switches off). If the DOOR LOCK led stays lit, it means that there is something that  needs to be checked before the door is opened (e.g.: there is water in the tub or the temperature of the water is too high).

Pressing the button again restarts the programme  from the point at which it was interrupted. PROGRAMME/ON-OFF knob: sets the desired programme (see page 6) and switches the machine on or off.

The knob stays still during the cycle.

Leds

• The LEDS provide important information.
• This is what they can tell you:
• Cycle phase under way:
• During the wash cycle, the LEDs gradually illuminate on to indicate the cycle phase under way:

Note: during draining, the LED corresponding to the  Spin cycle phase will be turned on.

Function buttons

The FUNCTION BUTTONS also act like LEDS.

• When a function is selected, the corresponding button is illuminated.
• If the function selected is incompatible with the programme set, the button will flash and the function will not be enabled.
• If you set a function that is incompatible with another function you selected previously, only the last one selected will be enabled.

DOOR LOCK led:

• If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damages, wait for the LED to flash before you open the appliance door.
• The rapid flashing of the DOOR LOCK Led together with the flashing of at least one other LED indicates there is an abnormality. Call for Technical Assistance.

Briefly: starting a programme

• Switch on the washing machine by turning the PROGRAMME/ON-OFF knob to the desired programme.
  • All the LEDS will light up for a few seconds and the DOOR LOCK Led will begin to flash.
• Load your laundry into the washing machine and shut the appliance door.
• Set the wash temperature (see page 7).
• Add the detergent and any fabric softener (see page 8).
• Start he programme by pressing the START/PAUSE button.
  • If you want to cancel the cycle set, turn the PROGRAMME/ON-OFF knob to the position and wait for all the LEDs to illuminate and then turn off again.
  • If another programme is not selected, the DOOR LOCK led will remain lit for about 1 minute.
• When the programme is finished, the DOOR  LOCK Led will flash to indicate that the appliance door can be opened. Take out your laundry and leave the appliance door ajar to allow the drum to dry thoroughly.
  • Switch the washing machine off by turning the PROGRAMME/ON-OFF knob to the position.

Proaramme table

Notes: For the anti-crease function, please see page 7. The information contained in the table is purely indicative.

Special programme

• Daily (programme 8 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts 30 minutes and allows you to save on both time and energy. By setting this programme (8 at 30°C), you can wash different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.
• We recommend the use of liquid detergent.

Personalisations

Setting the temperature

• Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 6).
• The temperature can be lowered, or even set to a cold wash ( ).

Functions

To enable a function:

1. press the button corresponding to the desired function, according to the table below;
2. the function is enabled when the corresponding button is illuminated.

Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the programme set.

Anti-crease

• This function interrupts the wash programme, and the washing is left to soak in water before the appliance is drained. It is enabled in programmes 5 – 6 – 7 – 9- 10 and Delicate rinse cycle.
• To conclude the cycle, press the START/PAUSE button.
• To run the draining cycle alone, set the knob to the relative symbol taj and press the START/PAUSE button.

Detergents and laundry

Detergent dispenser

• Good washing results also depend on the correct dose of detergent: adding too much detergent won’t necessarily make for a more efficient wash, and may in fact cause build up on the interior of your appliance and even pollute the environment. 200006
• Open up the detergent dispenser and pour in the detergent and fabric softener, as follows.
• compartment 1: Detergent for pre-wash (powder)
• compartment 2: Detergent for the wash cycle (powder or liquid)
  • Liquid detergent should only be poured in immediately prior to the wash cycle start.
• compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow from the grid.

• Do not use hand wash detergent because it may form too much foam. Preparing your laundry
• Divide your laundry according to:
  • the type of fabric/the symbol on the label.
  • the colours: separate coloured garments from whites.
• Empty all pockets and check for loose buttons.
• Do not exceed the weight limits stated below, which refer to the weight when dry:
  • Sturdy fabrics: max 5 kg
  • Synthetic fabrics: max 2.5 kg
  • Delicate fabrics: max 2 kg
  • Wool: max 1 kg

How much does your laundry weigh?

• 1 sheet 400-500 g
• 1 pillow case 150-200 g
• 1 tablecloth 400-500 g
• 1 bathrobe 900-1,200 g
• 1 towel 150-250 g

Special items

• Curtains: fold curtains and place them in a pillow  case or mesh bag. Wash them separately without exceeding half the appliance load. Use programme 10 which excludes the spin cycle automatically.
• Quilted coats and windbreakers: if they are padded with goose or duck down, they can be machine-washed. Turn the garments inside out and oad a maximum of 2-3 kg, repeating the rinse cycle once or twice and using the delicate spin cycle.
• Trainers: remove any mud. They can be washed together with jeans and other tough garments, but not with whites.
• Wool: for best results, use a specific detergent, taking care not to exceed a load of 1 kg.

Precautions and advice

The washing machine was designed and built in compliance with the applicable international safety regulations. The following information is provided for your safety and should consequently be read carefully.

General safety

• This appliance has been designed for non- professional, household use and its functions must not be changed.
• This washing machine should only be used by  adults and in accordance with the instructions provided in this manual.
• Never touch the washing machine when barefoot or with wet or damp hands or feet.
• Do not pull on the power supply cable to unplug the appliance from the electricity socket. Pull the plug out yourself.
• Do not open the detergent dispenser while the appliance is in operation.
• Do not touch the drain water as it could reach very high temperatures.
• Never force the washing machine door: this could damage the safety lock mechanism designed to prevent any accidental openings.
• In the event of a malfunction, do not under any circumstances touch internal parts in order to attempt repairs.
• Always keep children well away from the appliance while in operation.
• The appliance door tends to get quite hot during the wash cycle.
• Should it have to be moved, proceed with the  help of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy.
• Before loading your laundry into the washing machine, make sure the drum is empty.

Disposal

• Disposing of the packaging material: observe local regulations, so the packaging can be re-used.

The European Directive 2002/96/EC on Waste

• Electrical and Electronic Equipment, requires that  old household electrical appliances must not be  disposed of in the normal unsorted municipal waste  stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment.
• The crossed out “wheeled bin” symbol on the  product reminds you of your obligation, that when you dispose of the appliance it must be separately collected.
• Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.
• Saving energy and respecting the environment

Environmentally-friendly technology

• If you only see a little water through your appliance  door, this is because thanks to the latest Indesit  technology, your washing machine only needs less than half the amount of water to get the best results: an objective reached to respect the environment.

Saving on detergent, water, energy and time

• To avoid wasting resources, the washing machine should be used with a full load. A full load instead of two half loads allows you to save up to 50% on energy.
• The pre-wash cycle is only necessary on extremely soiled garments. Avoiding it will save on detergent, time, water and between 5 and 15% energy.
• Treating stains with a stain remover or leaving them to soak before washing will cut down the need to wash them at high temperatures. A programme at 60°C instead of 90°C or one at 40°C instead of 60°C will save up to 50% on energy.
• Use the correct quantity of detergent depending on the water hardness, how soiled the garments are and the amount of laundry you have, to avoid wastage and to protect the environment: despite being biodegradable, detergents do contain ingredients that alter the natural balance of the environment. In addition, avoid using fabric softener as much as possible.
• If you use your washing machine from late in the afternoon until the early hours of the morning, you will help reduce the electricity board’s peak load.
• If your laundry has to be dried in a tumble dryer, select a high spin speed. Having the least water possible in your laundry will save you time and energy in the drying process.

Care and maintenance

Cutting off the water or electricity supply

• Turn off the water tap after every wash. This will limit the wear of your appliance’s water system and also prevent leaks.
• Unplug your appliance when cleaning it and ring all maintenance operations.

Cleaning your appliance

The exterior and rubber parts of your appliance can be cleaned with a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser

• Remove the dispenser by pulling it out (see figure).
• Wash it under running water; this operation should be repeated frequently.

Caring for your appliance door and

Always leave the appliance door ajar to prevent unpleasant odours from forming.

Cleaning the pump

• The washing machine is fitted with a self-cleaning  pump that does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the pre-chamber that protects the pump, situated in the lower part of the same.
• Make sure the wash cycle has ended and unplug the appliance.

To access the pre-chamber:

• using a screwdriver, remove the cover panel on the lower front of the washing machine (see figure):
• unscrew the lid rotating it anti- clockwise (see figure): a little water may trickle out. This is perfectly normal;
• clean the interior thoroughly;
• screw the lid back on;
• reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.
  • Checking the water inlet hose
  • Check the water inlet hose at least once a year. If you see any cracks, replace it immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.
  • Never use hoses that have already been used.

Troubleshooting

Your washing machine could fail to work. Before calling for Assistance (see page 12), make sure the problem can’t easily be solved by consulting the following list.

Service

Before calling for Assistance:

• Check whether you can solve the problem on your own (see page 11);
• Restart the programme to check whether the problem has been solved;
• If this is not the case, contact an authorised Technical Service Centre on the telephone number provided on the guarantee certificate.
• Always request the assistance of authorised servicemen.

Notify the operator of:

• the type of problem;
• the appliance model (Mod.);
• the serial number (S/N).

This information can be found on the data plate situated on the rear of the washing machine.

Frequently Asked Questions

What is the capacity of the Indesit WIA 101 Washing Machine?

The Indesit WIA 101 has a capacity ranging from 1 to 5 kg for laundry.

How do I level my Indesit WIA 101 Washing Machine?

To level the machine, adjust the adjustable front feet on a flat and sturdy floor. Ensure the angle of inclination does not exceed 2 degrees.

What is the voltage requirement for the Indesit WIA 101?

The Indesit WIA 101 requires a voltage of 220/230 Volts at 50 Hz.

Can I use an extension cord with the Indesit WIA 101 Washing Machine?

No, it's not recommended to use extensions or multiple sockets with the washing machine.

How do I connect the water inlet hose to the Indesit WIA 101?

Insert seal A into the hose and screw it onto a cold water tap with a 3/4 gas threaded mouth. Ensure the water runs clear before making the connection.

What should I do if the water inlet hose is too short for my setup?

If the hose is too short, contact a specialist store or authorized serviceman for an extension.

How do I connect the drain hose of the Indesit WIA 101?

Connect the drain hose without bending it to a draining duct or wall drain situated between 65 and 100 cm from the floor.

Can I use hose extensions for the drain hose?

It's advised against using hose extensions, but if necessary, the extension must have the same diameter as the original hose and not exceed 150 cm in length.

What is the maximum spin speed of the Indesit WIA 101?

The maximum spin speed of the Indesit WIA 101 is up to 1000 rpm (revolutions per minute).

How do I start the first wash cycle with the Indesit WIA 101?

Run a wash cycle with detergent and no laundry, setting the 90°C program without a pre-wash cycle after installation.

What are the dimensions of the Indesit WIA 101 Washing Machine?

The dimensions of the Indesit WIA 101 are 59.5 cm wide x 85 cm high x 52.5 cm deep.

Can I wash different fabric types together in the Indesit WIA 101?

It's recommended to divide your laundry based on the type of fabric and color to achieve the best results.

Reference:Indesit WIA 101 Washing Machine Instructions Manual- device.report

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>