Godox MG2400Bi Bi Color LED Light Instruction Manual

Godox MG2400Bi Bi Color LED Light

Important Safety Instructions and Precautions

First of all, as the most basic principle: This product is a professional lighting set of equipment and should be used by professional lighting engineers or under the guidance of professionals.
Basic safety attentions must always be followed during use, as follows:

1. Before use, please read and understand these instructions and attention.

2. Professional lighting is prohibited for children. When children are near, parents or accompanying- ing persons must supervise closely to prevent children from personal injury due to collision with lamps or private use of lamps.

3. This lighting product is not ordinary and cannot be used for general lighting. Anyone who has suffered eye damage or has sensitive eyes should avoid using this product.

4. When the lamp is on, it must be used with care. Do not touch high-temperature parts, such as LED lamp beads, to avoid burns.

5. When the lamp is on, it is forbidden to look directly at the lamp beads under any circumstances. Strong light should be used under the guidance of professional lighting engineers. Avoid prolonged exposure to strong light under any circumstances. If eye discomfort, please turn off the lamp in time, suspend use, and see a doctor immediately.

6. If the lamp bead is damaged or deformed by heat, stop using this equipment, and contact the manufacturer, service agent, or qualified maintenance personnel to replace the lamp bead in time to avoid accidents.

7. This product is only suitable for use in -20C to 45C operating environments and normal humidity environments.

8. Do not use damaged equipment or accessories, and wait for professional maintenance personnel to check and repair to confirm that they are normal before use.

9. During use, if the casing of this product is broken due to being dropped, squeezed or subjected to strong impact, please do not use it, to avoid electric shock injury due to contact with internal electronic components.

10. If an extension cord is required, please use an extension cord with a current rating greater than or equal to that of the equipment. If an extension cord is rated less than the equipment, overheating may result.

11. Some products have long power cords, please place the power cords properly and keep them in a safe place. Avoid contacting the power cord with overheating surfaces, and avoid improper placement that could cause pulling damage or trip on-site personnel. Please use the certified power cord from the original manufacturer. If the product is damaged by using a non-certified power cord, it will not be repaired by our factory.

12. Be sure to unplug equipment from the power outlet before cleaning and repairing. When not in use, do not pull the power cord to unplug the equipment. For normal power-off, please hold both ends of the plug of the equipment with your hands and pull the plug out of the power outlet.
    This equipment needs to be connected to a grounded outlet.

13. Do not disassemble the product without permission. If the product fails, it must be checked and repaired by authorized maintenance personnel.

14. Before storing, make sure that the equipment has cooled down completely. For storage, unplug the power cord from the equipment. The equipment should be placed in the carrying case or a ventilated dry place.

15. Do not place equipment near flammable and volatile solvents such as alcohol and gasoline.

16. Do not use accessories that are not recommended by our factory to avoid fire, electric shock, or personal injury.

17. When cleaning, do not wipe it with a damp cloth, please use a dry cloth or a soft cloth to wipe the dirt off the equipment.

18. Please take off the protective cover before using it.

19. This product complies with ROHS, CE, and FCC certification, please refer to the relevant national standards for use and operation.

20. The safety instructions are formulated according to the strict testing of the factory, and the design and specifications of the equipment are subject to change without prior notice. For the latest product information, please check the GODOX website and view the latest electronic instructions.

21. One-year warranty period, accessories such as consumable batteries, adapters, power cords, etc. are not covered by this warranty.

22. If it is found that the equipment is repaired without authorization, the one-year warranty period will be canceled and relevant fees will be charged for maintenance.

23. Machine failures caused by non-standard operation are not covered by the warranty.

keep these instructions!

Forward
Thank you for purchasing！
MG2400Bi is a brand-new high-power LED light, with the following powerful features and functions:
input power of 2900W, support 100V-240V~50/60Hz power supply which allows you to use it anywhere in the world, ultra-high and thousand-bit adjustable brightness, separate design of light body and controller, IP54 rate, four dimming curves, wide CCT range from 2800K to 6500K, CRI≥96 & TLCI≥96, various wireless controlling methods, etc. This new product is suitable for shooting scenes in large-scale photography studios, film and television studios, broadcast studios, outdoor exteriors, and large field scenes.

Main Features

• 2600W strong output power in full CCT range.
• Thousand-bit adjustable brightness from 0％ to 100％.
• The wide CCT range is adjustable from 2800K to 6500K.
• Super high CRI: CRI≥96，TLCI≥96
• Four dimming curves: linear, S-curve, exponential, logarithmic.
• Various wireless controlling methods: support DMX 512/LumenRadio CRMX/Bluetooth App control.
• With the brand-new Godox G-Mount, communication contacts, and intelligent accessory recognition, the safety index for the use of high-power lighting fixtures is significantly improved.
• IP54 rate keeps the light head and controller from dust and water.
• Adopt an efficient heat dissipation system design with a large fan to meet the cooling needs of a large LED light.
• 11 FX modes: flash, lightning, cloudy, broken bulb, TV, candle, fire, firework, explosion, welding, SOS.

Warning

• Do not look directly at the LED light or illuminate others’ eyes.
• Do not plug or unplug the power cable or connecting cable when the power is turned on, otherwise personal injuries may occur.
• Do not cover the heat dissipation vent in working status.
• Keep out of reach of children.
• Please make sure to follow the instruction manual and correctly use this professional lighting device.
• Don’t stare at a bright light source

Name of Parts

Light Body

1. Handle 1
2. Handle 2
3. Direction Adjustment Handle
4. DC Input Port
5. Lanyard Attachment
6. Yoke
7. Mount Locking Pusher
8. Godox G-Mount
9. Quick Install Device

Controller

1. Antenna Port
2. Remove Controller Port
3. DC Output Port
4. PRESET Button
5. LOCK Button
6. MENU Button
7. MODE Button
8. Adjust Dial
9. Wireless CRMX Indicator
10. Power Switch
11. Display
12. DMX OUT Port
13. DMX IN Port
14. AC Input Port
15. Ethernet Port

What’s Inside

What’s Inside MG2400Bi

What’s Inside MG2400Bi K1

What’s Inside MG2400Bi K2

Note: Due to continuous updates and upgrades of the products, there may be differences between the actual products and the pictures. Therefore, the pictures are for reference only, products to prevail in kind.

Optional Accessories

Installation and Disassembly

Installing the Yoke

1. Place the light on a flat surface with the heat dissipation side upward.
2. Press down the quick install device button and remove the wrench.
3. Align both ends of the yoke with the quick install device, lock the wrenches on both sides, and then the “click” indicates a successful installation.
4. Install the light on the roller stand and lock the fixing knob on the roller stand.

Note: The roller stand is sold separately.

Please be careful when installing the light as it is quite heavy.

Disassembling the Yoke

1. Hold the handle of the light and remove it from the roller stand then place it on a flat surface.
2. Press and hold the quick install device button and release the wrench to remove the yoke.

Installing/Disassembling the Light Protection Cover

1. Align the light protection cover with the mount and rotate clockwise to install.
2. Press and hold the mount locking pusher and rotate counterclockwise to remove the light protection cover.

Installing/Disassembling the Reflector

1. Align the reflector with the mount, insert, and then rotate clockwise to install.
2. Press and hold the mount locking pusher and rotate counterclockwise to remove the light protection cover.

Note: Make sure to align the reflector with the mount of the lamp head.

Installing the Controller on the Light Stand

1. Loosen the handle of the pipe clamp and insert the light stand pole, rotate the handle clockwise to lock the mounting device, then align the quick install device with the slot of the mounting device and insert it.

AC Power Cord Connection Instructions

• Wire 1 (yellow) is the ground wire, wire 2 (black) is the neutral wire, and wire 3 (red) is the live wire.
• Please ensure proper connection by matching the corresponding wires to the appropriate terminals on the plug before use.

Connect to DMX 512 Controller

1. Wireless DMX Connection
2. Wired DMX Connection

Connect to Ethernet

Connection 1

Connection 2

Power Supply

Note: Do not plug or unplug the power cord or connecting cable when the power is turned on, otherwise injuries may occur.

Power On/Off
Connect the device to the power source and briefly press the power switch button on the controller to turn it on or off.

CCT Mode

• Briefly press the MODE button to switch to CCT mode. Briefly press the adjust dial to switch between the brightness setting interface and the color temperature setting interface.

• In the brightness setting interface, turn the adjust dial to adjust the brightness ratio from 0% to 100%.

• Turning the adjust dial clockwise once will increase the value by 0.1 unit, while turning it counterclockwise once will decrease the value by 0.1 unit. Quick adjustment is also available during rapid rotation.

• In the color temperature setting interface, turn the adjust dial to adjust the color temperature from 2800K to 6500K.

• Turning the adjust dial clockwise once will increase the value by 100 units, while turning it counterclockwise once will decrease the value by 100 units.

FX Mode

• Briefly press the MODE button to switch to FX mode. Turn the adjust dial to switch among the following 11 effects: flash, lightning, cloudy, broken bulb, TV, candle, fire, firework, explosion, welding, SOS.
• Select the desired lighting effect and briefly press adjust the dial to enter the effect setting interface.

Flash Effect

In the flash effect setting interface, turn the adjust dial to select options among switch, dim, CCT, auto, manual, speed, mode, etc. Briefly press the adjust dial to select the desired option then turn the dial to adjust the options (except for the auto and manual options). Finally, continuously press the adjust dial/briefly press the MODE button to return to the previous menu.

• Switch: Turn on/off the effect
• Dim: 0％-100％
• CCT: 2800K-6500K
• Speed: 1-100
• Mode: Camera Flash/Flash Bulb

Note: If the manual is selected, the flash effect can be triggered once by briefly pressing the adjust dial.

Lightning Effect

In the lightning effect setting interface, turn the adjust dial to select options among switch, dim, CCT, auto, manual, times, frequency, etc. Briefly press the adjust dial to select the desired option then turn the dial to adjust the options (except for the auto and manual options). Finally, continuously press the adjust dial/briefly press the MODE button to return to the previous menu.

• Switch: Turn on/off the effect
• Dim: 0％-100％
• CCT: 2800K-6500K
• Times: Random/1-10
• Frequency: Random /2-20

Note: If the manual is selected, the lightning effect can be triggered once by briefly pressing the adjust dial.

Cloudy Effect

In the cloudy effect setting interface, turn the adjust dial to select options among switch, dim, ratio, speed, etc. Briefly press the adjust dial to select the desired option then turn the dial to adjust the options. Finally, continuously press the adjust dial/briefly press the MODE button to return to the previous menu.

• Switch: Turn on/off the effect
• Dim: 0％-100％
• Ratio：10％-90％
• Speed: Random/1-100

Broken Bulb Effect

In the broken bulb effect setting interface, turn the adjust dial to select options among switch, dim, CCT, speed, etc. Briefly press the adjust dial to select the desired option then turn the dial to adjust the options. Finally, continuously press the adjust dial/briefly press the MODE button to return to the previous menu.

• Switch: Turn on/off the effect
• Dim: 0％-100％
• CCT：2800K-6500K
• Speed: 1-100

TV Effect

In the TV effect setting interface, turn the adjust dial to select options among switch, dim, speed, etc. Briefly press the adjust dial to select the desired option then turn the dial to adjust the options. Finally, continuously press the adjust dial/briefly press the MODE button to return to the previous menu.

• Switch: Turn on/off the effect
• Dim: 0％-100％
• Speed: 1-100

Candle Effect

In the candle effect setting interface, turn the adjust dial to select options among switch, dim, speed, etc. Briefly press the dial to select the desired option then turn the adjust dial to adjust the options. Finally, continuously press the adjust dial/briefly press the MODE button to return to the previous menu.

• Switch: Turn on/off the effect
• Dim: 0％-100％
• Speed: 1-100

Fire Effect
In the fire effect setting interface, turn the adjust dial to select options among switch, dim, speed, etc. Briefly press the adjust dial to select the desired option then turn the dial to adjust the options. Finally, continuously press the adjust dial/briefly press the MODE button to return to the previous menu.

• Switch: Turn on/off the effect
• Dim: 0％-100％
• Speed: 1-100

Firework Effect
In the firework effect setting interface, turn the adjust the dial to select options among switch, dim, speed, embers, etc. Briefly press the adjust dial to select the desired option then turn the dial to adjust the options. Finally, continuously press the adjust dial/briefly press the MODE button to return to the previous menu.

• Switch: Turn on/off the effect
• Dim: 0％-100％
• Speed: 1-100
• Embers: 01-100

Explosion Effect
In the explosion effect setting interface, turn the adjust the dial to select options among switch, dim, CCT, auto, manual, speed, embers, etc. Briefly press the adjust dial to select the desired option then turn the dial to adjust the options (except for the auto and manual options). Finally, continuously press the adjust dial/briefly press the MODE button to return to the previous menu.

• Switch: Turn on/off the effect
• Dim: 0％-100％
• CCT: 2800K-6500K
• Speed: 1-100
• Embers: 1-100

Note: If the manual is selected, the explosion effect can be triggered once by briefly pressing the adjust dial.

Welding Effect
In the welding effect setting interface, turn the adjust dial to select options among switch, dim, CCT, speed, etc. Briefly press the adjust dial to select the desired option then turn the dial to adjust the options. Finally, continuously press the adjust dial/briefly press the MODE button to return to the previous menu.

• Switch: Turn on/off the effect
• Dim: 0％-100％
• CCT: 2800K-6500K
• Speed: 1-100

SOS Effect
In the SOS effect setting interface, turn the adjust dial to select options among switch, dim, CCT, etc. Briefly press the adjust dial to select the desired option then turn the dial to adjust the options. Finally, continuously press the adjust dial/briefly press the MODE button to return to the previous menu.

• Switch: Turn on/off the effect
• Dim: 0％-100％
• CCT: 2800K-6500K

Note: The default dimming curve in FX mode is linear.

Menu Settings

Briefly press the MENU button to enter menu settings, and turn the adjust dial to select among the following options: DMX, CRMX, Bluetooth, Network settings, Art-Net & sACN, optics recognition, power limit dimming curves fan, display, language, version & upgrade, factory reset, fixture info.

DMX

Briefly press the adjust dial to enter the DMX setting interface. Turn the adjust dial to select options among address, DMX mode, RDM state, DMX lost, termination, and extend DMX channels. Briefly press the adjust dial to select the desired option then turn it to adjust settings. Finally, briefly press the adjust dial to exit the current setting, and press the MENU button to return to the previous menu.

use the last received DMX control signal until powered down or a valid DMX control signal is received again.
Black Out| The light is off immediately.
Black Out After 2 Min| After the DMX control signal is lost, continue to use the last received DMX control signal for 2 minutes then blackout.

Note: If a valid DMX control signal is received within 2 minutes, then

use the new DMX control signal.

Termination| On| Turn on the DMX terminal
Off| Turn off the DMX terminal
Extend DMX Channels| On| Turn on extending DMX channels
Off| Turn off extend DMX channels

Note: Please refer to the DMX Practical Table to control the device by DMX/RDM. The electronic version can be downloaded from the official website https://www.godox.com.

CRMX
Briefly press the adjust dial to enter the CRMX setting interface. Turn the adjust dial to select options between switch and mode. Briefly press the adjust dial to select the desired option then turn it to adjust settings. Finally, briefly press the adjust dial to exit the current setting, press the MENU button to return to the previous menu.

Note: Before selecting the transmit mode/receive mode, perform a reset first.

mode)
11dBm| Output power value = 11dBm (only adjustable in transmitter mode)
16dBm| Output power value = 16dBm (only adjustable in transmitter mode)
20dBm| Output power value = 20dBm (only adjustable in transmitter mode)
Status| Link| To enter linked status (only adjustable in transmitter mode)
Linking| Linking (only adjustable in transmitter mode)

Bluetooth
Briefly press the adjust dial to enter the Bluetooth setting interface. Turn the adjust dial to select options between switch and reset. Briefly press the adjust dial to select the desired option then turn the dial to adjust settings. Finally, briefly press the MENU button to return to the previous menu.

Scan the QR code to download the “Godox Light” smartphone app version 3.0 or above (which can be used in Android and iOS).

Note: The app can be used directly on the firstly installed device (smartphone or iPad). When changing to another mobile device (smartphone or iPad), the light shall be reset before the normal connection of the app.

Network Settings
Briefly press the adjust dial to enter the network settings interface. Turn and briefly press the adjust dial to select network mode, then turn the dial to select DHCP, Art-Net 2. x, Art-Net 10. x, and manual. Finally, briefly press the MENU button to return to the previous menu.

address is 2. B.C.D in Art-Net 2. x mode.

The ID address is 10. B.C.D in Art-Net 10. x mode. In manual mode:

AAA＝0-255

BBB＝0-255 CCC＝0-255 DDD＝0-255

Subnet Mask| 255.BBB.CCC.DDD| The subnet mask is 255.BBB.CCC.DDD and can not be adjusted by menu settings in DHCP/Art-Net 2.x/Art-Net 10. x mode.

In manual mode:

AAA＝0-255 BBB＝0-255 CCC＝0-255 DDD＝0-255

Default Gateway| AAA.BBB.CCC.DDD| The default gateway is assigned by DHCP in DHCP mode. The default gateway is 2. B.C.D in Art-Net 2. x mode.

The default gateway is 10. B.C.D in Art-Net 10. x mode. In manual mode:

AAA＝0-255

BBB＝0-255 CCC＝0-255 DDD＝0-255

Art-Net & sACN
Briefly press the adjust dial to enter the Art-Net & sACN setting interface. Turn and briefly press the adjust dial to select options among auto, Art-Net, sACN, and off, then other level 2 options are available to adjust. Finally, briefly press the MENU button to return to the previous menu.

accepted. Art-Net： Only Art-Net protocol.

sACN： Only sACN protocol.

Off： No network protocols are accepted.

Art-Net Net| 0-127| Art-Net network
Art-Net Sub-Net| 0-15| Choose the Art-Net subnet in the Art-Net network.
Art-Net Port| 0-15| Art-Net port
Art-Net Universe| 0…32767| Art-Net universe
sACN Universe| 1…63999| sACN universe

Optics Recognition
Briefly press the adjust dial to enter the optics recognition setting interface. Turn and briefly press the adjust dial to turn the function on or off. Finally, briefly press the MENU button to return to the previous menu.

Note: The light will not be lightened if the optics are not correctly installed even optics recognition function is turned on.

Power Limit
Briefly press the adjust dial to enter the power limit setting interface. Rotate and briefly press the adjust dial to turn the function on or off. Finally, briefly press the MENU button to return to the previous menu.

Max. limit:10%-100%

Note: If the power supply environment is unable to meet the requirements for powering on, you can activate this function while the device is in the powered-off state. Simultaneously press the Preset button and MODE button, and the device will automatically enter the Power Limit mode upon startup (default power limitation is set to 50%).

Dimming Curves
Briefly press the adjust dial to enter the dimming curves setting interface. Rotate and briefly press the adjust dial to choose among linear, S-curve, exponential, and logarithmic. Finally, briefly press the adjust dial/MENU button to return to the previous menu.

Fan
Briefly press the adjust dial to enter the fan setting interface. Rotate and briefly press the adjust dial to choose among mute, auto, medium, and high. Finally, briefly press the adjust dial/MENU button to return to the previous menu.

Display
Briefly press the adjust dial to enter the display setting interface. Rotate and briefly press the adjust dial to adjust display brightness from 10％ to 100%. Finally, briefly press the MENU button to return to the previous menu.

Language
Briefly press the adjust dial to enter the language setting interface. Rotate and briefly press the adjust dial to select between Simplified Chinese and English. Finally, briefly press the MENU button to return to the previous menu.

Version & Upgrade
Briefly press the adjust dial to enter the version & upgrade setting interface to check the firmware version of the lamp head & controller and upgrade instructions. Then, short press the MENU button to return to the previous menu.

Factory Reset
To access the factory reset interface, briefly press the adjust dial. Rotate the adjust dial to select “Yes” or “No,” then briefly press the adjust dial to complete the setting. Once you have confirmed the factory reset, the light fixture will restart, and the interface will automatically display options for Chinese and English. Rotate the dial to select an option and then press the dial to confirm the setting. At this point, the brightness value of the light will automatically be set to 100% and the interface will return to the CCT mode interface.

Fixture Info
Briefly press the adjust dial to enter the fixture info setting interface to check the model, UID NO., the firmware version of the lamp head and controller, light head temp., lamp maintenance time reminder, certification, etc. Then, briefly press the MENU button to return to the previous menu.
When the lamp head displays a remaining maintenance time of 0 hours, it is recommended for the customer to clean the glass or other parts of the lamp head. We suggest using a dry or soft cloth to wipe away any dirt or debris on the equipment. Once the maintenance is complete, if you choose to reset, the lamp head maintenance time will start counting again.

Lock Setting

Briefly press the LOCK button, the panel is locked when < > is displayed on the panel, briefly press again to unlock.
Note: The locking function only works on the controller panel, other operations are still available.

Preset Setting

Briefly press the PRESET button to enter the preset effects interface. Rotate and briefly press the adjust dial to choose and enter preset effects 1-20, then briefly press to select save or cancel. Then, briefly press the adjust dial to return to the previous menu and briefly press the PRESET button to exit.

• Apply: Apply this set of preset lighting effects.
• Save: Save the current lighting effect of the light fixture.
• Cancel: Return to the previous interface.

Note: If light effect data has been previously saved, there will be an additional option.

Software Upgrade

The firmware version of the controller

1. Download the new firmware to the U disk from the official website (https://www.godox.com.cn/-firmware-continuous-light).
2. Turn off the device. Insert the U disk with new firmware into the USB Type-A port.
3. Turn on the device, and the MG2400Bi controller will automatically enter the upgrading interface.
4. It will return to the main interface after completion.

The firmware version of the lamp head

1. Download the new firmware to the U disk from the official website (https://www.godox.com.cn/-firmware-continuous-light).
2. Turn off the device. Insert the U disk with new firmware into the USB Type-C port.
3. Turn on the device, and the MG2400Bi lamp head will automatically enter the upgrading interface.
4. It will return to the main interface after completion.

Notes

1. New firmware must be downloaded from the official website, and only one BIN file in the root directory of the USB disk.
2. The USB Type-A port can only support output voltage and current of 5V/1.5A. Do not connect to an over-rated USB device.

Version &Upgrade

• Insert The U Disk With New Firmware After Power Off, Then Reboot To Upgrade The Device.
• Box:0.13 Lamp: V0.03

Maintenance

• This product, except for consumables, is supported with a one-year warranty.
• Unauthorized service will void the warranty.
• Maintenance of the light must be performed by our authorized maintenance department which can provide original accessories.
• If the product fails or becomes wet, do not use it until it is repaired by professionals.
• Shut down the device immediately should abnormal operation be detected.

Photometric Data

CCT| Testing

Condition

| Illuminance Unit| 3m| 5m| 7m| 9m| 10m
---|---|---|---|---|---|---|---
2800K| ****

Bare Light

| lux| ≈8810| ≈3540| ≈2120| ≈1480| ≈1250
fc| ≈818| ≈329| ≈197| ≈137| ≈116
3200K| lux| ≈9700| ≈3950| ≈2360| ≈1640| ≈1380
fc| ≈901| ≈367| ≈220| ≈152| ≈128
4300K| lux| ≈11600| ≈4740| ≈2840| ≈1920| ≈1650
fc| ≈1080| ≈440| ≈264| ≈179| ≈153
5600K| lux| ≈12000| ≈4890| ≈2900| ≈1970| ≈1700
fc| ≈1120| ≈454| ≈269| ≈183| ≈158
6500K| lux| ≈11300| ≈4650| ≈2730| ≈1870| ≈1600
fc| ≈1050| ≈432| ≈254| ≈174| ≈149
CCT| Testing

Condition

| Illuminance Unit| 3m| 5m| 7m| 9m| 10m
---|---|---|---|---|---|---|---
2800K|

With Reflector (45°)

| lux| ≈32200| ≈11700| ≈6240| ≈4000| ≈3380
fc| ≈2990| ≈1090| ≈580| ≈372| ≈314
3200K| lux| ≈35900| ≈13000| ≈6900| ≈4450| ≈3740
fc| ≈3340| ≈1200| ≈641| ≈413| ≈348
4300K| lux| ≈43200| ≈15700| ≈8340| ≈5370| ≈4490
fc| ≈4020| ≈1460| ≈775| ≈499| ≈417
5600K| lux| ≈44600| ≈16200| ≈8590| ≈5520| ≈4650
fc| ≈4140| ≈1500| ≈798| ≈513| ≈432
6500K| lux| ≈42100| ≈15300| ≈8110| ≈5260| ≈4400
fc| ≈3910| ≈1420| ≈753| ≈489| ≈408

The above data are not absolute values but rather average values. All tests were conducted with the light at 100% brightness.

Technical Data

Waterproof Grade of Light

Body/Controller

| IP54
Controlling Methods| DMX 512 Control(support RDM protocol/LumenRadioCRMX)/RC-A6 Remote Control/Bluetooth App Control /Ethernet (support Art-Net & sACN protocol)/Remove Controller/Light Body Control（Remove Controller RC11 is

sold separately）

Bluetooth Controlling Distance| Max. 100m
USB Type-A Port| Firmware Upgrade/5V  1.5A Power Supply
Dimension（Yoke and reflector are not included in the light

body）

| Light Body：16.10” ×15.16”×14.02”

Controller：11.02‘16.54“8.27”

Net weight≈| Light Body（Yoke and reflector not included）：20kg

Controller：13kg

Specifications and data may be subject to changes without notice.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.

Warning

• Operating frequency: 2402MHz – 2480MHz（BT）
• Maximum EIRP Power: 5dBm

Declaration of Conformity

• GODOX Photo Equipment Co., Ltd. hereby declares that this equipment complies with the
  essential requirements and other relevant provisions of Directive 2014/53/EU. By

• Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states. For more information on DoC, Please click this web link:

• https://www.godox.com/eu-declaration-of-conformity/

• The device complies with RF specifications when the device is used at 0mm from your body.

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and keep it. Thank you!

Product

Information

| Model| Product Code Number
---|---|---
Customer Information| Name| Contact Number
Address

Seller Information

| Name
Contact Number

Address

Date of Sale
Note

Note: This form shall be sealed by the seller.

Applicable Products

The document applies to the products listed on the Product Maintenance information (see below for further information). Other products or accessories (e.g. promotional items, giveaways additional accessories attached, etc.) are not included in this warranty scope.

Warranty Period
The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day(purchase date) when the product is bought for the first time, And the purchase date is considered as the date registered on the warranty card when buying the product.

How to Get the Maintenance Service
If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide a valid warranty card. If you cannot provide a valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

Inapplicable Cases
The guarantee and service offered by this document are not applicable in the following cases: ① The product or accessory has expired its warranty period; ② Breakage or damage caused by inappropriate usage, maintenance, or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by an external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding, and damp environments, etc; ③ Breakage or damage caused by non- authorized institution or staff in the process of installation, maintenance, alteration, addition, and detachment; ④ The original identifying information of product or accessory is modified, alternated, or removed; ⑤ No valid warranty card; ⑥ Breakage or damage caused by using illegally authorized, nonstandard or non-public released software; ⑦ Breakage or damage caused by force majeure or accident; ⑧ Breakage or damage that could not be attributed to the product itself. Once met these situations are met, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories, and software that are beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion, and consumption are not the breakage within the maintenance scope.

Maintenance and Service Support Information

The warranty period and service types of products are implemented according to the following Product Maintenance Information:

Parts

|

Circuit Board

|

12

| The customer sends the product to the designated site

Battery

|

3

| The customer sends the product to the designated site
Electrical parts e.g.battery charger, etc.|

12

| The customer sends the product to the designated site

Other Items

| Power cord, lamp cover, locking device, package, etc.|

No

|

Without warranty

Godox After-sale Service Call +86-755-29609320(8062)

CONTACT

• GODOX Photo Equipment Co., Ltd.
• Add.: Building 2, Yaochuan Industrial Zone Tangwei Community, Fuhai Street, Baoan District,
• Shenzhen 518103, China Tel: +86-755-29609320(8062) Fax: +86-755-25723423
• E-mail: godox@godox.com.
• godox.com.

References

• GODOX Photo Equipment Co.,Ltd.
• GODOX Photo Equipment Co.,Ltd.
• Godox神牛 - 官方网站

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>