EUROPRO MIXPRO 70 Mixer User Manual

: June 16, 2024
: EUROPRO

Table of Contents

EUROPRO MIXPRO 70 Mixer
USER MANUAL
SAFETY
TECHNICAL CHARACTERISTICS
IDENTIFICATION OF THE COMPONENTS
USE OF THE MACHINE
SETTING OF THE LEVEL SENSOR
CLEANING PROCEDURE
DECLARATION OF CONFORMITY
WARRANTY
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EUROPRO MIXPRO 70 Mixer

You just acquired one of our machines and all the team of Europe Projection thanks you for the confidence you have granted us.
Manufacturer of professional equipment for paint and fillers, we have put our know-how for 25 years at the service of the users of our machines.
Our technical & commercial team is at your disposal for any further information you may need about the machine you just acquired.

USER MANUAL

IMPORTANCE OF THE MANUAL

This manual is a key part of the use of your machine. It summarizes the procedures of starting up, cleaning and maintenance of the device and also the safety instructions you need to observe.
Read carefully all the working and safety instructions and the warnings included in this manual before starting your machine.
Most of the accidents are caused by non-compliance with safety standards and rules.
This manual must be kept near the machine, within reach of the user and held in good condition until the final destruction of the machine.
In case of loss or deterioration of the manual, you can ask the machine manufacturer mentioned on page 4 for a copy at any moment.

RECEIVERS OF THE MANUAL
This manual is intended to any staff which will manipulate the machine :

people in charge of the transport of the machine
people in charge of the use of the machine
people in charge of the cleaning and maintenance of the machine
people in charge of the final destruction of the machine

SAFETY

Using the machine in an incorrect way or in non-compliance with the safety instructions indicated in this manual can cause death or serious injuries.
Read carefully all the working and safety instructions and the warnings contained in this manual before starting your machine.

Respect all the safety standards before running the equipment.
Use the equipment only for the applications specified in the manual.
Always remain alert when using the equipment.
Transport the machine using the handles or the appropriate grips.
During the breaks, disconnect electrically the machine.
Run the equipment to its nominal voltage.
Let at least 50 cm of free space between the equipment and any obstacle so that the airflow is not blocked.
Know how to quickly stop the equipment in case of necessity.
Never use the equipment while it is running abnormally or it is defective.
Do not direct a water jet or flammable liquid on the machine.
Never direct an air jet or product jet on a person or an animal.
Do not touch the warm surfaces of the equipment.
Always wear adequate body protection (glasses, gloves, overalls and mask) and pay attention to long hair.
Never touch moving parts.
Do not insert any object or the hands inside the protection grids to avoid any accident or damage to the machine.
For any outside job, only use appropriate extension cords.
Maintain the equipment carefully and clean it properly after every use.
Disconnect the equipment before any intervention.
Avoid unscrewing any connection while the machine is under pressure.
Check the damaged parts.
Do not clean the plastic parts with solvents.
In case of damage to the electric cable or the plug, do not run the machine and contact a licensed After-Sale Service to put genuine parts instead of the defective ones.
In case of needed After-Sale Service, always specify the machine model and its serial number.
For any replacement of parts, only use genuine parts.
Do not modify the machine.
Do not cut or dismantle the protection grids.
Do not open the electric box.

WORKSPACE

Maintain the workspace clean and clear.
The ambient operating temperature must be between 5°C and 35°C.
Do not use the equipment in a potentially explosive area.
Do not place any potentially inflammable objects close to the machine.
Take away every not qualified person from the working area of the machine, as well as children and animals.
In case of installation of the machine on scaffolding or a plan above ground level, attach the machine to avoid any fall while operating.
Do not install the equipment on an inclined surface to avoid the risks of unexpected moves or falls.

HOSES

Always use hoses and connections adapted to the used product (genuine parts), do not try to fix it.
Do not walk on the hoses, do not bend them.
Do not use the hoses to pull the machine.

STORAGE

Keep the equipment in a clean and clear area in which the temperature does not exceed +35°C.
After every use, necessarily grease the pump with a mixture of water + storage liquid to avoid it blocking up. The storage of a not-greased pump can damage it seriously.

IN CASE OF NECESSITY, WE SAVE OURSELVES THE RIGHT TO MAKE ANY USEFUL MODIFICATION WITHOUT ADVANCED NOTICE.

ELECTRIC CONNECTION

The electric connection of the machine must be on a 16A – 230V plug with a differential circuit breaker.
Before any intervention on the machine, make sure that every energy supply is cut (air and electricity).

GROUND CONNECTOR

All the machines must be connected to the ground when they work to protect the operator from electric shocks. Our machines are all equipped with standardized connection plugs.
The electric connection must be made by a qualified technician. It is forbidden to modify or dismantle the machine, especially the electric box.
Repairs must be made by an authorized centre or our After-sale Service.
During any intervention on the machine, make sure that the ground is well reconnected.

EXTENSION CORDS
During the use of an extension cord, make sure that it is not crushed or damaged and that it contains a ground. Check that the section of the used extension cord is sufficient to support the machine when it is working. A too- thin extension cord can cause voltage drops or overheating of the machine.
In the case of the use of a cable reel, it is imperative to unwind it entirely, otherwise, the equipment can be damaged. The section must be proportional to the length of the cord.

END OF LIFE OF THE PRODUCT
At its end of life, the machine must not be eliminated with the other household waste. The uncontrolled elimination of waste can harm the environment or human health. Individuals are invited to contact the distributor who sold them the product or to inquire with their city hall to know where and how to get rid of the product so it can be recycled while respecting the environment.
Under the regulation of Waste of Electrical and Electronic Equipments (WEEE), we undertake to process the used EEEs according to the following provisions: applicable only to products on the market since 08/13/05, under the brands EUROPE PROJECTION or VOLUMAIR, products of other brands sold by our company (upon presentation of the corresponding invoices), products that operate using electrical energy (for example, thermal washers or compressors do not fall into this category).

Treatment modality
WEEE returns are collected by our clients/distributors at their own expense to our collection points in Antony (92) or Rousset sur Arc (13). Upon receipt, the products are sorted by our employees and directed to the most appropriate processing channels.
For any further information, please contact our hotline at +33 4 42 29 08 96 or conseil@euromair.com.

DESCRIPTION
The MIXPRO 70 mixer allows a quick and homogeneous mixing of powdered products. It is equipped with a speed controller and a water doser. Its control panel with a digital display is easy to use.
This mixer can be used to work with machines such as Compact-Pro (models 10 to 50) with the supplied frame.
The 4-position adjustable frame is adapted to receive the MIXPRO 70 mixer. With a spacing of 535mm between its feet, a Compact-Pro machine type 10 to 50 may be slid underneath.

TO USE WITH
All types of mono-component powder products.

Do not use corrosive, acid or other types of products susceptible to damage the tank or the blade.
The water distribution circuit is expected to be used only with water. The use of another product, whatever it might be, can seriously damage the machine.

TECHNICAL CHARACTERISTICS

Machine compatible with: CP Joint 10, CP 10, 15, 20, 25, 30, 35, 40, 45 & 50
Mixing type: Continuous
Motor: 0,75 kW
Forward / reverse rotation speed: 50 to 280 RPM
Power supply: 230 V – 10 A – 50 & 60 Hz
Tank capacity: 40 L
Water meter: integrated
Mixing paddle: continuous Scew
Loading height: 129 cm
Dimensions (L x w x h): 133 x 73 x 92 cm
Dim. high position (L x w x h): 98 x 73 x 129 cm
Weight: 41 kg (60 kg with the frame)

IDENTIFICATION OF THE COMPONENTS

A Safety grid
B Water supply quick coupling
C Water flow-rate adjustment valve
D Level sensor
E Product outlet
F Control panel (see next page)

G	Motor speed display in %	H	Water volume display
1	Start / Stop	L1	Power on light
2	Start / Stop of the mixing in manual mode	L2	Manual mode

USE OF THE MACHINE

PREREQUISITES

The electric connection has to be 230 V – 16 A – 50 or 60 Hz with a 3 x 1,5 mm cable reel of 40m maximum, completely unreeled.

START / STOP

Once the machine has been connected, the machine is in stop mode, and the display (G) shows OFF.
With one push of the ON/OFF button (1), the display (G) shows the set value of the speed in %, the warning light (L1) lights up, and the machine is ready.
When the machine is working (warning light (L1) is on), one push of the button ON/OFF (1) will switch the machine off. The display (G) will show OFF and the warning light (L1) will switch off.

In case of a dysfunction of the machine, one 3-second push on the ON/OFF (1) will allow you to verify that the power supply is over 210 V.

STARTING UP

Once the mixer is connected, the display (G) will show AU (emergency stop). Turn the red button (AU) to deactivate it.
The display (G) shows OFF, press the ON/OFF button (1) to turn the mixer on.
The display (G) corresponds to the mixing speed from 0 to 100%, and the display (H) corresponds to the water flow rate in litres per hour.
Connect the mixer to the water supply with the quick coupling (B).
Place a bucket under the product outlet (E).
Press the WATER BACK button (6) and set the water flow rate to 250 L/h (indicated on the display (H)) using the adjustment valve (C).
Put the mixer in manual mode by pressing the button (2), and the light (L2) lights up.
Set the mixing speed to 50% using the arrows (4) and (5).
Break the powder bags on the grid (A) to fill the tank.
Press button (2), the mixer starts.
Let the product flow into the bucket for about 20 seconds, until the mixing has stabilised. The product will be very liquid at first, then reach the desired consistency, depending on the settings selected.
If the product is too liquid, use valve (C) to reduce the water flow rate. If the product is too dry, increase the water flow rate with valve (C).
To adjust the setting, increase or decrease the speed on the display (G) using buttons (4) and (5).
Increasing the speed will make the product drier, decreasing the speed will make it less dry.
When the desired texture is reached, press button (2) to put the mixer in stop mode, the light (L3) lights up.
If the mixer is used alone, press button (2) again to return to manual mode, and the light (L2) will light up.
If the mixer is coupled to a spraying machine, switch it to automatic mode with a button (3). The product will flow through the outlet (E) into the machine tank. The level sensor (D) automatically switches the mixer on or off depending on the level of the product in the tank (see 5. Setting of the level sensor).

ERROR CODES
The different error codes show up on the display (G).

CODES	DEFINITION	TO DO
	No display.	Plug the machine into the power supply, and ensure the power

supply is

230 V, verify the fuse in the electric box.

If the problem persists or if in doubt about the good running of the machine, do not try to repair it by yourself or to dismantle it.
Contact an authorized After-Sale Service or our hotline: +33 4 42 29 08 96.

SETTING OF THE LEVEL SENSOR

This operation must be carried out within 5 minutes after switching the mixer on, otherwise the level sensor will be locked.

Place a piece of white paper in the spraying machine* tank (photo 1), 2 centimetres above the desired minimum product level (diagram 2).
Place a screwdriver on the level sensor (photo 3) until LEDs Y and Z flash rapidly (6 Hz). Remove the screwdriver, the sensor is reset.
Replace the screwdriver until LEDs Y and Z flash slowly (2 Hz), and remove the screwdriver.
Replace the screwdriver, LEDs Y and Z will freeze. Remove the screwdriver.
Repeat the previous operation once.

This step can be done by filling the tank with the product instead of white paper.

When the product in the machine’s tank reaches the minimum level previously set, the mixer will restart (if AUTO mode is activated – (light (L4) on)) until the tank is filled to the set level.
Once the set level has been reached, the mixer will run for 25 seconds (mixing time). Depending on the flow rate of the spraying machine, increase or decrease the mixing time by following the procedure below.

SETTING THE MIXING TIME

Press MANU/STOP (2) and then ON/OFF (1) and keep both buttons pressed.
Release only the MANU/STOP button (2), and the light (L2) will flash.
NB: The ON/OFF button (1) must be held permanently until the end of the procedure.
Press once on MANU/STOP (2), the display (G) indicates H02. Press MANU/STOP (2) a second time, the light (L4) flashes and the display (G) indicates 25 seconds.
Use arrows (4) and (5) to set the new mixing time.
Once the time has been set, press AUTO (3) to confirm the operation.
Release ON/OFF (1).

CLEANING PROCEDURE

Unplug the mixer from the electrical supply before any intervention.

Unscrew the clamping knobs (J) and (K) from the product outlet.
Remove the mixing chamber (M), the mixing shaft (N) and the outlet (L) and clean these 3 parts.
Clean the powder outlet of the mixing chamber on the mixer (O).

The direct projection of water under pressure onto the control panel has to be stopped at the risk of water infiltration into the electric box. Proceed by simply cleaning with a humid sponge.

DECLARATION OF CONFORMITY

THE MANUFACTURER

EUROPE PROJECTION
228, avenue Olivier Perroy
13790 ROUSSET

DECLARES THAT THE EQUIPMENT DESIGNATED BELOW

Trademark: EUROPE PROJECTION
Type: Mixer
Model: MIXPRO 70

COMPLIES WITH THE DIRECTIVES

Machines 2006/42/CE
Low voltage 2014/35/UE
CEM 2014/30/UE
ROHS 2011/65/UE
Noise emissions 2005/88/CE

WARRANTY

WARRANTY CONDITIONS

Each equipment is delivered inspected and tested.
We exclude any warranty for visible defects, not notified by the customer within 48 hours.
The equipment sold is guaranteed during the manufacturer’s warranty from the date of purchase, as specified on the original proof of purchase, and under the conditions defined by the manufacturer.
This warranty covers any equipment against any manufacturing or material defect, under normal conditions of use. Insofar as the customer is presumed to be a professional of the same field of specialty, this warranty covers only the defect of conception of the equipment rendering it unfit for its use, which could not be detected by a professional buyer.
The defects or deteriorations caused by natural wear, external accident or a modification, use, storage or treatment of the equipment not planned by the manufacturer, nor specified by ourselves, are excluded from any warranty.
Are expressly excluded from the warranty the defects resulting from an improper use, the application of abrasive or corrosive products, an inappropriate installation, negligence, an insufficient maintenance or cleaning, inappropriate conditions of storage, chemical, electronic or electric influences, any change in the normal process of use.
The following wearing parts are not covered by the warranty (non-exhaustive list): rotors, stators, driving shafts, connecting rods, seals, cleaning balls, spray guns, lance, nozzle, hose, needle kits, cylinders, piston rods, prime/spray valve assy, seal kits, membranes, suction and delivery valves, carding machine vanes, filters, oils, chains and quick-release clip.
The warranty also excludes the equipment on which the serial number was erased or made illegible, on which unauthorized people made attempts of repair, which were totally or partially dismantled.
Our equipment is covered by a manufacturer’s warranty (parts and labour) of 12 months following the purchase date by the final customer, without exceeding 24 months from the date of purchase by the client.
This manufacturer’s warranty shall automatically cease if the customer does not resell the equipment within 24 months of its purchase. The cases of exclusion of warranty mentioned in the articles above are also applicable to our own equipment.
The manufacturer’s warranty shall always be subject to the presentation of the purchase invoice.
If the defective equipment is covered by the manufacturer’s warranty, it shall be repaired or replaced at our discretion free of charge.
If the defective equipment is not covered by the manufacturer’s warranty, we shall issue a quote for the repair that we shall submit to the customer for approval.
Except as otherwise required by law, this manufacturer’s warranty is exclusive of all other warranties, including the statutory warranty of hidden defects.
In case of intervention of our services on a breakdown caused by the customer or an incident excluded in the conditions referred to above, the costs of repair and transport shall be invoiced to the customer.
We exclude all liability for indirect damages suffered by the customer, such as, but not limited to, loss of income, turnover, loss of profits, loss of image, of any kind whatever.
In all cases, our liability shall be limited to the amount paid by the customer for non-compliant equipment.
Any legal action of the customer against us relating to the warranty of the equipment shall be barred 1 year after the date of discovery of the defect. The customer shall have to prove the date of this discovery.

Request for Warranty

For any request related to the repair of equipment covered by the manufacturer’s warranty, the customer shall have to fill out the warranty form, available on our website, under After-Sale Service.
- For a full dossier, the following documents shall have to be attached:
- the purchase invoice of the final user
- pictures of the defective parts of the equipment
- a description of the breakdown
- the quote of labour if the customer is certified by EUROMAIR for repairing the equipment
No invoice of labour shall be taken into account without our prior approval.

Analysis of the breakdown by our technical department
A file number shall be given to the customer and an answer shall be provided within 48 working hours after
reception, provided that the warranty request is considered as full.
In the event the equipment is covered by the manufacturer’s warranty, we shall confirm the warranty to
the customer and send him a quote (without price) detailing the parts to be changed and any comments.
Return of replacement parts

Replacement parts must be ordered with a warranty agreement number and will be made available to the customer at our factory.
The conditions of return of the equipment are detailed in our Delivery terms.
In the case of a warranty claim on an on-board component such as a Kohler, Honda or Vanguard engine in a machine manufactured by us, only the manufacturer of the component can validate the warranty coverage.
In this case, the request must be addressed directly to the manufacturer of the component or its nearest authorised representative. The Euromair, Euromair MPC or Mixer service centres may be considered as the manufacturer’s representatives if they are the closest. As this principle also applies to batteries, our supplier Parts Holding Europe, or one of its sister companies remains your contact for your requests (https://www.partsholdingeurope.com/).

CONTACT

EUROPE PROJECTION – 228, avenue Olivier Perroy 13790 ROUSSET – Tél : +33 (0)4 42 29 08 96 – Fax : +33 (0)4 42 53 44 36
SAS au capital de 400 000 € – RCS Aix-en-Provence B 394 961 510 – NAF 2892 Z – Intracom : FR 54 394 961 510
More information on www.euromair.com.

EUROPE PROJECTION