fingers WL5 Wireless CMOS Imaging Barcode Reader User Guide

fingers WL5 Wireless CMOS Imaging Barcode Reader

Important – Warnings and Safety Instructions

1. Do not place the Barcode Scanners near the heat sources such as fire, radiators, stoves, light candles and other apparatus that produces heat.
2. Use only those accessories supplied by FINGERS.
3. It is recommended to refer all servicing to qualified personnel. Servicing is required when the Barcode Scanner has been damaged in any way. Any evidence of any attempt to open and/or alter the device, including any scratch, peeling, puncturing, or removal of any of the labels, will void the Limited Warranty.

In the box

• 1 N x 2D QuickScan WL5 Barcode Reader
• 1 N x USB Receiver
• 1 N x Stand
• 2 N x USB Type-C Cable
• 1 N x Quick Start Guide
• 1 N x Brand Note

Care and Maintenance

1. Unplug the Barcode Scanner before cleaning it.
2. Use soft, damp cloth (water only) to clean the surface.
3. Do not use any chemicals, solvents, or cleaning solutions containing alcohol, ammonia or abrasives.
4. Do not allow any liquid to enter into any of the openings.

Connecting the Reader

Reading Techniques

1. The viewfinder projects an aiming beam that should be centered over the barcode. However, it can be tilted at any angle and in any direction for an effective read.
2. Hand hold the scanner over the barcode, pull the trigger and position the aiming beam on the barcode.
3. The aiming beam is smaller when scanner is placed closer to the barcode and larger when it is farther from the code.
4. Hold the scanner close to the smaller barcodes, and farther away from bigger barcodes to get a good read.
5. If the barcode is highly reflective (ex. Laminated sheets, glossy), you might be required to position the scanner at an angle in such a way the barcode can be read and scanned clearly.

Note:

1. If the scanner beeps once, the link has been established.
2. The scanner will tum off in 20 seconds with a long, when in idle mode.
3. To use it again, press the button and two beeps will be heard.

All the parameter settings of the scanner can be finished by scanning the barcodes and saving them in the storage. Even while being switched off, these setting do work.

Standard Product Defaults

The following barcode resets all standard product default settings.

Note: Scan the above QR code to enable or disable Keyboard in the 10S device.

Pairing Instruction

1. Barcode Scanner Pairing with Receiver
2. Steps 1. Scan below pairing Code I, Code II in sequence, and the scanner LED indicator become red and flashing.
3. Steps 2. Connect the USB receiver to the PC or Laptop, wait till the LED indicator of both the barcode scanner and USB receiver LED turns blue after successful pairing.
4. Barcode scanner pairing with Bluetooth device
5. Step 1. Scan Below Pairing Code I, Code II in sequence and the scanner LED indicator became red and flashing.
6. Step 2. Open the Bluetooth in the Bluetooth device and search for the barcode scanner which named “2DQuickS canWL5” and click connect, wait a second, the barcode scanner LED indicator becomes red after successful pairing.
7. Wired Mode

Note: This barcode scanner can use as wired through an extra data cable. Just need to scan the above code.

Standard Product Defaults

1. Normal Mode : The data will be uploaded to the host device immediately after scan, if out of range it will not save the data, and there will b eeps out of range.
2. Inventory Mode: The data will be saved in the memory chip, and upload data to host device as instructed.
3. Eg: Scan the “Upload all data and clear”, the scanner will upload all data saved in the memory chip and cleared the original data.
4. Data upload Instruction In Inventory Mode
5. Automatic Storage Mode: The data will be uploaded to host device immediately after scan if the scanner in range, the data will be saved in the memory chip if the scanner out of range which heard 2 alarm beeps, press the scanner Tigger to upload the saved data in the memory chip will be cleared.

Cursor Setting

Keyboard Caps Lock Control

Sleep time setting

• Transmit Speed
• Image Reverse
• Keyboard language

UPC-A Converts EAN13 Settings

Scan Mode

Suffix Setting

Example: Add Suffix “A”

1. Step 1 : Scan the above barcode to enter into “Add Suffix”
2. Step 2: Scan the next barcode to add Suffix “Suffix”
3. Step 3 : Scan the numeric code correspond to “A” the ASCII value of A in Hexadecimal is “4” & “1” (Refer to Appendix 1 & Appendix 2)
4. Step 4: Scan “save” code to save (refer to Appendix 1)

Prefix Setting

Note : The method of adding Prefix is same as Suffix setting as above

Buzzer

Appendix 1

Appendix 2

Product Specifications

General

• Type  Wireless (BT) I Wired
• Interface USB Receiver
• In -built Memory 4MB
• Indicators Beeper, LED
• Operation Mode Trigger
• Barcode Type Support
  1 D: EAN, UPC, Code 39, Code 93, Code 128, UCC/EAN 128, Codabar, lnteMeave 2 of 5, ITF-6, ITF-4, ISBN, ISSN, MSI-Plessey, GS 1 Oatabar,GS 1 Composite Code, Code 11, Industrial 25, Standard 25, Plessey, Matrix 2 of 5. 2D: QR Code, Data Matrix, PDF417, Aztec, Maxicode, Micor QR, Micor PDF417,Hanxin Code .

Connection

• BT Version  V4.0
• Frequency 2402 MHz – 248 0 MHz
• Effective Range 30 – 50 meters (Open Space)

Optical

• Light Source 617nm LED Aimer, White LED
• Scan Rate 20otimes/sec
• Resolution 1O>5 mil
  • 20>10mil
• Print Contrast Ratio 20%
• Depth of Field
  • EAN 13 50-200 mm (13 mil);
  • QR 25 – 240 mm (20 mil);
  • PDF417 30 – 130 mm (6.67 mil)

Electrical

• Input Voltage DC 5V±5%
• Working Current 26 0mA
• Standby Current 0mA
• Sleep Mode 26mA

Battery

• Battery Type Lithium
• Battery Capacity 2200mAh
• Charging Type USB Type-C Cable
• Charging Time About 5 hours

Physical

• Housing Material ABS+PC
• Charging Cable Type USB Type-C (1.20 meters)
• Dimensions 15.4 (H) x 6.5 (W) x 6.2 (L) cm
• Weight 201 grams (without receiver)
• Color Black+ Grey

Environment & Safety  Conformance

• Operating Temperature 0 c – 40°C
• Storage Temperature 40°C – 10°c
• Operating Humidity 5% – 85% (non-condensing)
• Shock Resistance 1.5 m drops

fingers.co.in

Images shown may vary from actual product • Specifications, features and appearance are subject 10 change wi1holl1 notice.• All logos, brands, 1rademarks and product names are properties of their respective owners. • Produc1 warranty is governed by warranty terms mentioned on www.flngers.co.in • This product falls under a-waste (Management & Handling) Rules, 2011. For proper disposal method, visit our website www.flngers.co.in

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>