niko 350-41659 Presence Detector Dali Secondary Instruction Manual
- June 16, 2024
- niko
Table of Contents
350-41659
350-41659 Presence Detector Dali Secondary
Read the complete manual before carrying out the installation and activating the system. Keep the manual for future reference.
DESCRIPTION
This motion detector registers movement via a passive infrared sensor (PIR).
You use this device in combination with a DALI master (350-41657, 350-41650 or
350-41680) to expand the detection area. A maximum of 20 secondary detectors
can be connected to one master. Both the master and the secondary detector
have the same detection range (a circle with a diameter of 8 – 12 m). To cover
a complete surface with multiple detectors, it is recommended to take into
account an overlap of around 30 %.
The secondary detector controls the lighting according to the parameters set
on the master. For more information, consult the manual of the master.
The detector has a very flat design of only 5 mm, so that it can be mounted
almost flush with the ceiling.
INSTALLATION
2.1. Connection
Danger: Do not install the detector while it is connected to the mains voltage
supply. Do not connect the device to the power supply until the installation
is completed. It is not necessary to assemble the detector immediately because
it has removable connectors. This allows the connector first to be cabled
separately and then to be pushed back into the detector.
The detector is powered through the DALI bus. Refer to the wiring diagram in
fig. 1.
2.2. Mounting
Tip: Do not install the detector in the vicinity of heat sources such as
stoves or electric heaters, air currents (ventilation systems) or moving
objects (see fig. 2). This can activate the device unnecessarily because the
device reacts to movement and heat.
The detector is suitable for direct mounting in the ceiling (see fig. 4). As a
protection, the detector has a cover around the connectors. In addition, the
detector also has standard spring terminals that allow easy mounting in the
ceiling.
Note: It is important to install the secondary detector only after the
fittings have been programmed and divided into zones. Otherwise problems may
occur during programming and zone assignment.
MAINTENANCE
Dirt may prevent the detector from functioning properly. Therefore, always keep the lens clean and dry. Use a damp cloth and water with some detergent to clean the lens. Never exert pressure to wipe the lens clean. If the lens or other parts of the detector are defective, please contact an authorised installer.
TECHNICAL DATA
| visible dimensions (fig. 5) | 5 x 95 mm (HxW) |
|---|---|
| invisible dimensions (fig. 5) | 90 x 77 mm (HxW) |
| power supply | through the DALI bus |
| detection range | 8 – 12 m |
| detection angle | 360° |
| mounting height | 2.4 – 3 m |
| ambient temperature | 0 – +50 °C |
| protection degree | IP20 |
| protection class | class II devices, class I detector |
| quality mark | CE marked |
Warnings regarding installation
The installation of products that will permanently be part of the electrical
installation and which include dangerous voltages, should be carried out by a
qualified installer and in accordance with the applicable regulations. This
user manual must be presented to the user. It should be included in the
electrical installation file and it should be passed on to any new owners.
Additional copies are available on the Niko website or via Niko customer
services.
CE marking
This product complies with all of the relevant European guidelines and
regulations. For radio equipment Niko llc declares that the radio equipment in
this manual conforms with the 2014/53/EU directive. The full text of the EU
declaration of conformity is available at www.niko.eu
under the product reference, if applicable.
Environment
This product and/or the batteries provided cannot be disposed of in non-
recyclable waste. Take your discarded product to a recognised collection
point. Just like producers and importers, you too play an important role in
the promotion of sorting, recycling and reuse of discarded electrical and
electronic equipment. To finance the rubbish collection and waste treatment,
the government levies recycling charges in certain cases (included in the
price of this product).
Support & contact
nv Niko sa
Industriepark West 40
9100 Sint-Niklaas, Belgium
www.niko.eu
+32 3 778 90 80
support@niko.eu
Niko prepares its manuals with the greatest care and strives to make them as complete, correct and up-to-date as possible. Nevertheless, some deficiencies may subsist. Niko cannot be held responsible for this, other than within the legal limits. Please inform us of any deficiencies in the manuals by contacting Niko customer services at support@niko.eu.
PM350-41659R22381
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>