V-TAC VT-ST15 LED Solar Street Light Instruction Manual

V-TAC VT-ST15 LED Solar Street Light

Product Information: LED Solar Streetlight

Specifications

• Model: VT-ST15

Introduction
The LED Solar Streetlight is a high-quality lighting solution that harnesses solar power to provide illumination for outdoor areas. This product offers energy efficiency and environmental friendliness, making it an ideal choice for street lighting applications.

Warranty
The LED Solar Streetlight comes with a warranty. For any issues or queries related to the product, please reach out to us at support@v-tac.eu.

Warning

• Installation must be performed by a qualified electrician.
• Replace any cracked protective shield.
• Keep away from fire.
• Do not immerse in water.
• The luminaire cannot be installed in low-lying areas to prevent soaking.

Notice
The LED Solar Streetlight offers a working mode that can be controlled using the smart button. The lighting operation is as follows:

• ON/OFF: Press the smart button to turn the streetlight on or off.
• First 5Hrs Lighting: The streetlight will provide continuous lighting for the first 5 hours after being turned on.
• After 5Hrs Lighting or When Battery Capacity Below 30%: After the initial 5 hours of lighting, or when the battery capacity drops below 30%, the streetlight will adjust its lighting mode accordingly.

Product Usage Instructions

Installation A: Wall Mounted

1. Prepare the lamp, accessories, and tools.
2. Drill two 8mm holes with a depth of 60mm on the wall (Picture 1).
3. Insert the expansion screws into the holes (Picture 2).
4. Using a wrench, fix the lamp on the wall by tightening the expansion screws (Picture 3).

Installation B: Straight Pole

1. Prepare the lamp, accessories, and tools.
2. Remove the nut spacer from the U-shaped brackets (Picture 1).
3. Use the U-shaped brackets to fix the lamp on the pole (Picture 2).
4. This installation is suitable for poles with a diameter of 40-60mm.

Installation C: Curved Pole

1. Prepare the lamp, accessories, and tools.
2. Loosen the screws and remove the bracket (Picture 1 & 2).
3. Move the cover of the lamp socket (Picture 3).
4. Attach the arch-shaped bracket to the lamp socket without fully tightening it (Picture 4).
5. Set up the lamp onto the lamp pole (Picture 5).
6. Balance and adjust the lamp’s position, then lock the arch-shaped bracket securely (Picture 6).
7. This installation is suitable for poles with a diameter of 40-50mm.

FAQ

• Q: Can I install the LED Solar Streetlight myself?
  A: No, the installation must be performed by a qualified electrician to ensure proper and safe installation.

• Q: Can the streetlight be installed in low-lying areas?
  A: No, the streetlight should not be installed in low-lying areas to prevent soaking.

INSTRUCTION MANUAL LED SOLAR STREETLIGHT

TECHNICAL DATA

INTRODUCTION & WARRANTY

Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any another query, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at the best. The warranty is valid for 3 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. This product is warranted for manu facturing defects only.

MULTI-LANGUAGE MANUAL QR CODE
Please scan the QR code to access the manual in multiple languages.

IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: SUPPORT@V-TAC.EU FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST DEALERS. V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B

WARNING!

1. Installation must be performed by a qualified electrician
2. Replace any cracked protective shield.
3. Keep away from the fire.
4. Don’t immerse in the water
5. Luminaire cannot be installed in low-lying areas, so as not to soak.

This marking indicates that this product should not be disposed of with other household wastes.

NOTICE

1. This is a solar powered lamp, please install it in a location where can get enough sunshine.
2. Please note the lighting time depends on the sunshine duration & weather.
3. Built-in intelligent IC is with over-charge, over-discharge and over-voltage protection.
4. The lamp gets solar charged at day time, and light up automatically at dusk.
5. The lamp is equipped with an internal battery pack, which is replaceable. If any need, please contact seller for correct new battery pack.
6. If the battery is taken out and put back in or replaced with new ones, please toward the solar panel to sunshine or a strong light to activate the lamp.
7. Non-professionals please do not disassemble the lamp.
8. Please do not dispose the battery with household garbage to avoid explosion.

WORKING MODE

Smart Button

First 5Hrs Lighting

After 5Hrs lighting or When Battery capacity below 30%

3 DIFFERENT INSTALLATIONS Installation A: Wall Mounted

1. Prepare lamp, accessories and tools well firstly.
2. Drill two holes of 8mm with a depth of 60mm on the wall. (Picture 1 )
3. Fix the expansion screws into the holes. (Picture 2 )
4. Then use a wrench to fix the lamp on the wall with expansion screws. (Picture 3 )

Installation B: Straight Pole

1. Prepare lamp, accessories and tools well firstly.
2. Remove the nut spacer of U- shaped brackets. (Picture 1 )
3. Use the U-shaped brackets to fix the lamp on the pole. (Picture 2 )
4. Loosen the screws at both ends of the bracket and adjust the angle of the lamp as needed, which is 20° adjustable in clockwise direction and 10° adjustable in counterclockwise direction, then tighten the screws. (Picture 3 4 )

*This installation applies to the poles with a diameter of 40-60MM.

Installation C: Curved Pole

1. Prepare lamp, accessories and tools well firstly.
2. Loosen the screws and take off the bracket. (Picture 1 2 )
3. Move the cover of lamp socket. (Picture 3 )
4. Fix the arch-shaped bracket onto the lamp socket (do not lock first). (Picture 4 )
5. Set up the lamp onto the lamp pole. (Picture 5 )
6. Adjust the lamp and balance it, then lock the arch-shaped bracket. (Picture 6 )

*This installation applies to the poles with a diameter of 40-50MM.

References

• TAC.EU

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>