Digital Monitoring Products LT-0883 7000 Series Thinline Keypad User Guide
- June 4, 2024
- Digital Monitoring Products
Table of Contents
7000 Series Thinline™ and Aqualite™ Keypad
Quick Start Guide
LT-0883 7000 Series Thinline Keypad
This quick start guide walks you through installing the keypad.
https://play.google.com/store/apps/details?id=com.smart.tesla
Full Installation and Programming Guide
To view the full 7000 Series Thinline™ and Aqualite™ Keypad Installation
and Programming Guide, scan this QR
code or visit DMP.com.
Step 1: Remove the Cover
Insert a slotted-tip screwdriver into one of the slots on the bottom of the keypad and lift the screwdriver upward. Repeat with the other slot. Separate the cover from the base and set the cover containing the keypad components aside.
Step 2: Wire the Keypad
Use 1k Ohm EOL resistor on keypad zones 1-4.
- Connect the harness to the keypad header.
- Connect the red wire to panel terminal 7.
- Connect the yellow wire to panel terminal 8.
- Connect the green wire to panel terminal 9.
- Connect the black wire to panel terminal 10.
Models 7060/A, 7063/A, 7160, and 7163
are Supplied with a 4-wire harness for panel keypad bus connection.
Models 7070/A, 7073/A, 7170, and 7173
Supplied with a 12-wire data bus/zone harness. Four wires connect to the
keypad bus. The remaining eight wires are for the four-zone inputs, four wires
for each zone.
Models 7073/A and 7173
Supplied with a 5-wire output/reader harness and a 12-wire data bus/zone
harness.
Step 3: Wire for Access Control (Optional)
For all wiring instructions, scan the QR code at the beginning of the
document.
Step 4: Wire the Electronic Lock
The Form C relay on 7073/A and 7173 keypads draw up to 15 mA of current and
the contacts are rated for 1 Amp at 30 VDC maximum, resistive. The wires
marked NO C NC allow you to connect the device wiring to the relay for module
control. Use an additional power supply to power magnetic locks and door
strikes.
Step 5: Wire the 333 Suppressor
Use the included 333 suppressors with the keypad to suppress any surges caused
by energizing a magnetic lock or door strike. Install the 333 across the
keypad C (common) and NO (normally open) or NC (normally closed).
If the device is being controlled by the relay is connected to the NO and C
wires, install the suppressor on the NO and C wires. Conversely, if the device
is connected to the NC and C wires, install the 333 Suppressor on NC and C
wires.
Step 6: Mounting the Keypad
All DMP keypad housings are designed to install on any 4” square box, 3-gang switch box, compatible backboxes, or directly on a flat surface.
- Ensure all cables are routed through the keypad base cut-outs before fully mounting the base to the wall.
- Use #6 screws to secure the keypad base to the surface.
- Place the keypad cover back onto the base and snap it into place.
Step 7: Program the Panel and Keypad
For all programming instructions, scan the QR code at the beginning of the
document.
Step 8: Test the Keypad
For all testing instructions, scan the QR code at the beginning of the
document.
© 2022 LT-2584 22143
INTRUSION • FIRE • ACCESS • NETWORKS
2500 North Partnership Boulevard Springfield, Missouri 65803-8877
Domestic: 800.641.4282 | International: 417.831.9362
DMP.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>