Wrap X2 Body Worn Camera User Manual
- June 16, 2024
- Wrap
Table of Contents
- Wrap X2 Body Worn Camera
- Product Information
- CAMERA INTRODUCTION
- FEATURES
- SPECIFICATIONS
- Camera Power ON/OFF
- Audio Recording
- BUTTON/FUNCTION LEGEND
- Charging and Status LEDs
- Guide to Upload from Your MDT (Single-Dock Mobile or Desktop)
- Add Your Wrap Intrinsic Uploader (New Install)
- To Change to Record Reminder Feature
- FCC Warning
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Wrap X2 Body Worn Camera
Product Information
Specifications
- Video resolution: Up to 1440
- Low light: Auto/manual
- Camera resolution: 40MP
- FOV
- Battery life: Up to 14 hours
- Image stabilization: Yes
- Charging dock: Yes + data
- Charge time: 250 minutes
- Battery capacity: 3200mAh
- Storage: 64GB
- Video file format: .MP4
- Storage type: Internal
- Pre/Post Event Recording: Yes
- One-touch recording: Yes
- Record reminder: Yes
- GPS: Yes
- Bluetooth: Yes
- Photos while recording: Yes
- Password protection: Yes
- Waterproof rating: IP67
- USB: Yes
- LCD screen: Yes
- Weight (ounces): 5.75
- Dimensions: 3.3 x 2.2 x 1
- Warranty: 1 year & optional extended
- Multiple mounts: Yes
Camera Power ON/OFF
Power On/Standby:
When the camera is powered OFF, press and hold the power button for 3 seconds to turn the camera ON. The Status LED will be solid red.
Power Off:
When the camera is powered ON, press and hold the power button for 3 seconds to turn the camera OFF.
Video Recording
When the camera is powered on/standby mode but is not currently recording: If you press the Digital audio recording button during a video recording, the video recording will save to a file and begin a new digital audio recording.
Photograph – Snapshot Capture
When the camera is powered on/standby mode but is not currently recording, press photo button 1 or 2 to take a photograph. This will be a higher resolution photograph (note zoom-in and zoom-out features available).
Screenshot
When the camera is recording a video, press photo button 1 or 2 to take a snapshot from the recording video. This photo will be smaller in size than a regular photo. Note: Taking a screenshot does not disrupt your video recording. It copies one frame from your video as a photo and saves it separately from the video recording. The photo will be much smaller and of reduced quality.
Audio Recording
When the camera is powered on/standby mode but is not currently recording: Status LED will flash green while recording audio.
CAMERA INTRODUCTION
Wrap Intrinsic | Evidence on Cloud™
- Technical Support
- 800-583-2652, option 4
- support@wrap.com
To log onto Evidence on Cloud™:
Optional Mounts
Your kit contains:
- Camera
- USB Cable (1 m or 39 in)
- Alligator Clip Mount
- Camera Dock (Charging/Transferring)
- USB Cable (1 m or 39 in)
- 110-120V AC to USB Wall Charger
- Camera Introduction Booklet
FEATURES
- Battery life – up to 14 hours
- Front video record button
- Captures photos while video continues uninterrupted
- Digital Audio Recorder
- GPS
- One button activates “Discreet Mode”
- IP67
- Notifications & Alerts: Recording Reminder, Low Battery, Low Storage
- Secured: Evidence & Settings
SPECIFICATIONS
- Video resolution: Up to 1440
- Low light: Auto/manual
- Camera resolution: 40MP
- FOV: 140°
- Battery life: Up to 14
- Image stabilization: Yes
- Charging dock: Yes + data
- Charge time: 250 minutes
- Battery capacity: 3200mAh
- Storage: 64GB
- Video file format:.MP4
- Storage type: Internal
- Pre/Post Event Recording: Yes
- One-touch recording: Yes
- Record reminder: Yes
- GPS: Yes
- Bluetooth: Yes
- Photos while recording: Yes
- Password protection: Yes
- Waterproof rating: IP67
- USB: Yes
- LCD screen: Yes
- Weight (ounces): 5.75
- Dimensions: 3.3″ x 2.2″ x 1″
- Warranty:1 year & optional extended
- Multiple mounts: Yes
Camera Power ON/OFF
Power On/Standby
When the camera is powered OFF, press, and hold the power button for 3 seconds to turn the camera ON.
- The camera will vibrate once
- The status LED will turn solid green
- The LCD screen will remain off
- If using the Pre-Event Recording Mode feature, the Status LED will be solid red.
Power Off
When the camera is powered ON, press, and hold the power button for 3 seconds to turn the camera OFF.
- The camera will beep once
- The camera will quickly vibrate three times
- The Wrap Intrensic logo will display on the LCD screen
- The status LED will turn off
Video Recording
When the camera is powered on/standby mode but is not currently recording:
- Start = Single-Press the video recording button to start recording the video
- Stop = Double-Press (default) the video recording button again to stop the recording.
- There is an optional single-tap stop programmable in the camera manager
If you press the Digital audio recording button during a video recording, the video recording will save to a file and begin a new digital audio recording.
Photograph—Snapshot Capture
When the camera is powered on/standby mode but is not currently recording, press the photo button 1 or 2 to take a photograph. This will be a higher resolution photograph (note zoom-in and zoom-out features available.)
Screenshot
When the camera is recording a video, press photo button 1 or 2 to take a
snapshot from the recording video. This photo will be smaller in size than a
regular photo.
Note: Taking a screenshot does not disrupt your video recording. It
copies one frame from your video as a photo and saves it separate from the
video recording. The photo will be much smaller and reduced quality.
Audio Recording
When the camera is powered on/standby mode but is not currently recording:
- Start = Single-Press the audio recording button to start recording audio
Status LED will flash green while recording audio
- Stop = Double-press the audio recording button again to stop recording
If you press either of the Video recording buttons during a digital audio recording, the audio recording will save to a file and begin a new video recording.
BUTTON/FUNCTION LEGEND
Charging and Status LEDs
Fully charge the X2 camera using the included USB cable and charging dock for 3–4 hours.
-
* The charging indicator on the top of the camera will turn solid blue LED when charging. When the device is fully charged, the blue LED will turn off.
Guide to Upload to TOC (Multi-Camera “Kiosk Mode”)
Power the Wrap Intrinsic X2 Camera OFF and place in docking dtation. If the
camera is assigned and the PIN requirement is “OFF” the camera will
automatically begin to offload. If the camera is not assigned, you will see
this screen and must identify yourself prior to uploading if the PIN
requirement is OFF after selecting yourself from the list, the camera will
begin to offload. If the PIN requirement is ON for your agency, you will see
this screen and must code your PIN# for the camera to begin offloading. When
it’s completed, the message will display for 30 seconds after the offload to
indicate the offload is complete, and you may remove your camera.
Note: After the offload and upload to the cloud you may go to the link
below to identify and categorize your videos. A new screen “Evidence Labeling”
is now available to assist you in labeling your evidence.
Guide to Upload from Your MDT (Single-Dock Mobile or Desktop)
- From your MDT or desktop make sure the Wrap Intrensic uploader is installed per the previous instructions and connected to the single docking station with the USB cable provided.
- Power off the camera, then dock the Wrap Intrensic X2 camera in your single dock supplied (connected to MDT or desktop)
- When prompted, log in with your username and password (this tells the system where to park your files)
- Preview, edit, and add identifiers to your evidence, then hit “Send to Cloud”. The video will be copied from the camera to the computer where they will process and upload to the cloud.
- Once prompted, “Video Transferred, Safe to Remove your Camera”, unplug your camera and place back in service.
Add Your Wrap Intrinsic Uploader (New Install)
- Open your browser and go to app.intrensic.com
- Log in to the Wrap Intrinsic Evidence on CloudTM
- Select the last item in the menu: “Wrap Intrinsic Uploader”
- Click the icon to download then click set-up in the toolbar
- Follow the instructions to complete the set-up
To Change to Record Reminder Feature
(User Selectable)
Single press the first button on the back to wake up the device. Single press again to “Enter Password.” The password is [SIX] 0’s, or just hit the main “ENTER” button (the first button below the screen) six times.
- After entering the password, press button 3 to highlight the gear, and button 1 to select
- Press button 3 to scroll down to “record reminder” and select using 1. Scroll through the options and select with button 1
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Specific Absorption Rate (SAR) information: This X2 meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement
- This radio is designed for and classified as “General population/uncontrolled Use”, the guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.The exposure standard for wireless radio employs a unit of measurement known as the Specific Absorption Rate, or SAR, the SAR limit set 1.6W/kg.
- Body-worn operation; this device was tested for typical body-worn operations with the back of the handset kept 0mm for body worn. To maintain compliance with RF exposure requirements, use accessories that maintain a 0mm for body worn. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with RF exposure requirements, and should be avoided.
- The highest reported SAR value for worn on the body is 0.626 W/kg ©2023 WRAP TECHNOLOGIES, INC. | ALL RIGHTS RESERVED
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>