Holmes 32510140 16 Inch Digital Stand Fan Instruction Manual

: June 16, 2024
: Holmes

Table of Contents

Holmes 32510140 16 Inch Digital Stand Fan
Product Information
Product Usage Instructions
IMPORTANT SAFETY INSTRUCTIONS
PART SAND ASSEMBLY
FEATURES – OPERATIONS
Battery Replacement
OPERATIONS/CLEANING/MAINTENANCE
FCC STATEMEN T/WARRANTY INFORMATION
3 YEAR LIMITED WARRANTY
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Holmes 32510140 16 Inch Digital Stand Fan

Product Information

Specifications
- Fuse Type: Replaceable fuse
- Fuse Rating: 2.5 Amp, 125 Volt

Product Usage Instructions

Replacing the Fuse
- Unplug the fan by grasping the plug and removing it from the receptacle or outlet device. Do not unplug by pulling on the cord.
- Open the fuse cover located on the top of the plug by using your thumb or a flathead screwdriver to slide the cover towards the prongs. Ensure the fuse cover is completely open before attempting to remove the fuse.
- Carefully remove the fuse by using a small screwdriver to pry it from the compartment at the metal ends of the fuse.
- Place the plug on a solid, flat surface. Insert a new 2.5 Amp, 125 Volt fuse into the fuse compartment. Use a small screwdriver to secure the metal ends of the fuse into the compartment.
- Caution: Only replace the fuse with a 2.5 Amp, 125 Volt fuse.
- Slide the fuse cover closed completely. If the fuse cover is difficult to close, make sure the fuse is completely secured in place by pressing on the metal ends of the fuse.
- Caution: Do not replace the attachment plug. It contains a safety device (fuse) that should not be removed. Discard the product if the attachment plug is damaged.
Fan Blade Cleaning
- Remove the front grill by opening the clips located around the perimeter.
- Clean the fan blade, and front and rear grills with a soft cloth moistened with a mild soap solution.
- Securely fasten the front grill to the rear grill by closing the clips around the perimeter.
- Fan Head, Base, and Pole Cleaning
- Using a soft, moist cloth (with or without a mild soap solution), carefully clean the fan base, pole, and head.
- Use caution around the housing area. Do not allow the motor or other electrical components to be exposed to water.
FAQ
- Q: Where can I order a new fuse?
- A: You can order a new fuse from our website at www.getholmesfans.com.
- Q: Can I use a different rating fuse?
- A: No, you should only replace the fuse with a 2.5 Amp, 125 Volt fuse. Using a different rating fuse may cause damage or risk of fire.
- Q: Can I clean the fan with harsh chemicals?
- A: No, do not use solvents or benzene as a cleaner. Use a soft cloth moistened with a mild soap solution for cleaning.
- Q: How should I dispose of the product?
- A: For inquiries regarding recycling and proper disposal of this product, please contact your local waste management facility.
- Q: What is the FCC statement?
- A: The FCC statement states that this device complies with Part 15 of the FCC Rules and may not cause harmful interference. It has been tested and found to comply with the limits for a Class B digital device.
- Q: What should I do if the product causes interference?
- A: If the product causes harmful interference to radio or television reception, try repositioning the fan or using it in a different location. If the interference persists, contact customer support for further assistance.

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions should always be taken including the following:

Read all instructions carefully before using this appliance.
Use fan only for purposes described in the instruction manual.
This fan is not intended for continuous operation or equivalent.
To protect against electrical shock do not immerse the unit, plug or cord in water or spray with liquids and plug the appliance directly into a 120V AC electrical outlet.
Close supervision is necessary when any appliance is used near children.
Not intended for use by children. Unplug from the outlet when not in use, when moving the fan from one location to another, before putting on or taking off parts and before cleaning.
Avoid contact with moving parts.
Do not operate in the presence of explosive and/or flammable fumes.
To avoid fire hazards, never place the cord under rugs or any parts near an open flame, cooking or other heating appliance.
Do not operate any appliance with a damaged cord or plug, after the appliance malfunctions, or has been dropped/damaged in any manner. Discard the fan or contact customer service.
Do not run the cord under the carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not route the cord under furniture or appliances. Arrange the cord away from the traffic area so that it will not be tripped over.
The use of attachments not recommended or sold by the appliance manufacturer may cause hazards.
Do not let the cord hang over the edge of a table, counter or come in contact with hot surfaces or leave exposed to high-traffic areas.
Do not use outdoors. To disconnect, grip the plug and pull from the wall outlet. Never yank on the cord.
Always use on a dry, level surface.
Do not operate fan until fully assembled with all parts properly in place.
This product is intended for household use only and not for commercial or industrial applications.
WARNING: To reduce the risk of fire or electric shock do not use this fan with any solid-state speed control device.
WARNING: To reduce the risk of fire, electric shock or injury to persons, do not use replacement parts that have not been recommended by the manufacturer (eg: Parts made at home using a 3D Printer)
For models with overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short circuit may be present and the product should be discarded or contact customer service.

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other).
To reduce the risk of electric shock, this plug is intended to the outlet and reverse the plug. i siy does not, contact i fully ied electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY.

PART SAND ASSEMBLY

ASSEMBLY INSTRUCTIONS (SEE FIGURE 1)
NOTE: MAKE SURE YOU REMOVE ALL CONTENTS OF THE PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR PARTS THAT COULD BE REQUIRED TO OPERATE THIS FAN. Tools required: Phillips head screw driver (not included) Estimated assembly time: 5-10 minutes

To assemble the base, place Cross Base section (S) over top of Cross Base section (S).
Place Outer Pole (P) overtop of the assembled Cross Base.
Align the screw holes of the Outer Pole (P) to the Cross Base. the send eCos Bose wine trips head screwdriver.
Slide down the Base Cover (Q) overtop of the assembled Cross Base.
Loosen Fan Post Screw (M) and slide Motor Housing (K) over top of the Extension Pole (N). Tighten fan post screw (M).
Line up the 2 holes of the Rear Grill (H) with the posts on the Motor Housing (K) assembly. When properly aligned, the handle (1) of the rear grill
Secure Reor tril 7 to dor Housing (K) with Rear Grill Mounting Nut (G). Turn clockwise to tighten.
Slide Blade (F) over Motor Shalt (J).
Secure fan blade to motor shaft with the Blade Cap (E). Turn counter-clockwise to tighten.
Open the expandable Grill Clips (D) located around the perimeter of the Front Grill (B).
Big the he lofted it he born me l ill (H) with the hole at the bottom of the Front Grill (B).
Close all the Grill Clips (D) around the perimeter of the grill.
Insert the screw into the hole at the bottom of the grill. Secure in place by tightening the nut over the back of the screw.

Figure 1

A. Logo Plate
B. Front Grill
C. Grill Locking Screw
D. Grill Clips
E. Blade Cap
F. Blade
G. Rear Grill Mounting Nut
H. Rear Grill
I. Handle
J. Motor Shaft
K. Motor Housing
L. Digital Control Panel
M. Fan Post Screw
N. Extension Pole
0. Height Adjustment Collar
P. Outer Pole
Q. Base Cover
R. Outer Pole Screws
S. Cross Base
T. Remote Control

FEATURES – OPERATIONS

OPERATING INSTRUCTIONS

Set fan base on a dry, level, stable surface.
Plug cord into any standard 120 volt AC outlet.
To turn the fan on, press the POWER button located on the control panel or remote control. The fan will start running in the lowest setting “L” ( LOW).
Press the speed button to cycle through the below 3 speed settings in sequence. The corresponding indicator light will illuminate to confirm the selection: L-Low M-Medium H-High
To turn the oscillation on and off, press the oscillation button located on the control panel or remote control.
To set your tan to automatically shut ott, timer button located on the control panel or the remote other These rain oilin 0575 hours oly shut expired.
The fin wil rae throw, ores ating spe eus with brief pauses to simulate a natural outdoor breeze. To activate SLEEP mode, press the MODE button again. This function slows the BREEZE setting by one level every ten minutes unfil it reaches LOW.
To silence setting contirmation beeps, press the MUTE button (F) located on the remote control. To reactivate setting confirmation beeps, press the MUTE button again.
To turn the fan off press the power bution located on the control panel or remote control.
- A. Power / Speed Button (control panel)
- B. Speed Button (remote control)
- C. Timer Button
- D. Oscillation Button
- E. Mode Button
- F. Mute Button
- G. Mode Indicator Lights
- H. Timer Indicator Lights
- I. Speed Setting Indicator Lights

TILT ADJUSTMENT

Gently move the fan head up or down manually to the desired angle.

HEIGHT ADJUSTMENT

Turn the Height Adjustment Collar (0) counterclockwise to loosen the pole.
Adjust the Extension Pole (N) to the desired height, a dows righter the height adjustment collar in

REMOTE CONTROL: (SEE FIGURE 3)
NOTE: PLEASE REMOVE THE PROTECTIVE PLASTIC FROM THE REMOTE CONTROL BATTERY BEFORE OPERATION. This unit includes one lithium battery, CR2025/3V Remove the battery before discarding the remote.

Battery Replacement

The cells should be disposed of properly, including keeping them away from children. Even used cells may cause injury.

Locate the battery compartment on the bottom back of the remote control handset. Push the tab and pull the battery tray.
Remove the old battery.
Place the new battery into the battery compartment.
Slide the battery compartment into the remote control handset.

NOTES:

Remove the battery from the equipment when it is not being used for an extended period of time.
Remove the used battery promptly.
Do not discard used batteries into household trash containers. Contact your local government for disposal or recycling practices in your area.

OPERATIONS/CLEANING/MAINTENANCE

USER SERVICING INSTRUCTIONS
Follow these instructions to safely and correctly care for this fan.

REPLACEABLE FUSE

If the (2.5 Amp, 125 Volt) replaceable fuse blows, please visit our website at www.getholmestans.com. for information on how to order a new fuse.
Follow the below instructions to replace the fuse on the plug.

REPLACING THE FUSE

Unplug the fan. Grasp the plug and remove it from the receptacle or other outlet device.
- NOTE: Do not unplug by pulling on the cord.
Open the fuse cover, located on the top of the plug, by using your thumb or a head screwdriver to slide the cover towards the prongs.
- NOTE: Ensure the fuse cover is completely open before attempting to remove fuse
Remove the fuse carefully by using a small screwdriver to pry it from the compartment at the metal
Place the plug on a solid, flat surtace. Insert new 2.5 Amp, 125 Volt fuse into fuse compartment. Use a small screwdriver to secure the metal ends of the fuse into the compartment.
- CAUTION: Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse. The slide fuse cover closed completely. In us, I completely stirred in le by pressing on the metal ends of the fuse.
- CAUTION: Risk of fire. Do not replace the attachment plug. It contains a safety device (fuse) that should not be removed. Discard the product it the attachment plug is damaged.

FAN CLEANING

Always unplug the fan before cleaning.
Do not allow water to drip on or into fan housing.
Use only a soft cloth moistened with a mild soap solution.
Do not use harsh chemicals such as gasoline, thinner or benzene as a cleaner.

FAN BLADE CLEANING

Remove the front grill by opening the clips located around the perimeter.
Clean the fan blade, front and rear grills with a soft cloth moistened with a mild soap solution.
Securely fasten the front grill to the rear grill by closing the clips around the perimeter.

FAN HEAD, BASE AND POLE CLEANING

Using a soft, moist cloth (with or without a mild soap solution), carefully clean the fan base, pole and head.
Use CAUTION around the housing area. Do not allow the motor or other electrical components to be exposed to water.

FAN STORAGE

This fan can be stored either partially disassembled or assembled.
Store the fan in a clean, dry location between seasons or when not in use for an extended period of time.
Keep the fan protected from dirt and dust during storage.
NOTE: This fan can also be used during the cold winter season to circulate warm air throughout your home.
For inquiries regarding recycling and proper disposal of higermen please contact your local vuste

FCC STATEMEN T/WARRANTY INFORMATION

FCC STATEMENT
Potential for Radio/Television interference This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the product on or off, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the product and the receiver.
Connect the product into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The following importer is the responsible party:

Company Name: SEG Products US Corp.
Address: 8 The Green, Suite #6962, Dover, DE 19901
Telephone: 1-959-202-4223

3 YEAR LIMITED WARRANTY

This device has a limited warranty of 3 years from the original date of purchase against workmanship and defects in material. If under normal use, your product fails to operate, please contact our customer service department at [email protected]. A refund or replacement will be provided to you with proof of purchase. Star Elite Inc. may deny claims of damage caused by misuse or modifications of this product.
Warranty Service
Contact our customer service at www.getholmesfans.com/en/contact- us. or [email protected]. or 1-866-769-3166 (8:30 am – 5:00 pm EST) Monday-Friday. Our team will be happy to assist. www.getholmesfans.com. © 2023 Sunbeam Products, Inc. All rights reserved.