SamKnows SKWB8V3 Whitebox 8.0 with Wi-Fi Installation Guide
- June 6, 2024
- SamKnows
Table of Contents
Nielsen Broadband Panel
Whitebox
Installation Guide
What’s in the Box
Check to ensure you have the necessary parts; which should include:
- 1 x Whitebox
- 4 x Antennas
- 1 x Network cable
- 1 x Power supply
Connect antennas to the back of the Whitebox. (These are used to passively monitor nearby wireless networks for traffic, to ensure no tests are run when the line is active we do not monitor your traffic)
Connect
If you have combined modem/router
Connect one end of the network cable to a spare port on your
router. Connect the other end to the blue port marked “Internet” on the rear
of the Whitebox.
If you have a separate modem and router
Keep your NBN connection or modem connected to your separate router as usual.
Plug in wired devices
Disconnect any other wired network devices from your home
ADSL / cable router. Plug them into the ports marked 1 4 on the rear of the
Whitebox. (Please note the USB ports are non functional)
Power up
Connect the power supply to your Whitebox. Switch on at the mains socket, then
press the button on the back marked ‘ON/OFF’.
When the light below the ****icon remains steady the Whitebox is fully set up.
Log in
Your Whitebox is now ready to start testing your internet performance. You can
directly login into nbn-nielsenpanel.com to
check the status of your account.
Do not use the product in the environment at too high or too low temperature,
never expose the product under strong sunshine or too wet environment.
The suitable temperature for the product and accessories is 0 ℃-40℃.
When charging, please place the product in an environment that has a normal
room temperature and good ventilation. It is recommended to charge the product
in an environment with a temperature that ranges from 0 ℃~40 ℃. Please ensure
to use only the charger offered by the manufacturer. Using unauthorized
charger may cause danger and violate the authorization of the product and the
guarantee article.
This charger is for indoor use only.The charger type is S24B73-120A200-0K,
output voltage/current is 12Vdc/2A. The plug considered as disconnect device
of adapter.
If you use a third-party charger, the recommended output voltage/current of
the adaptor is 12dc/2A., and the adapter shall be CE approval type.
RF exposure information: The Maximum Permissible Exposure (MPE) level has been
calculated based on a distance of d=20 cm between the device and the human
body. To maintain compliance with RF exposure requirement, use product that
maintain a 20cm distance between the device and human body.
| Frequency bands | Max EIRP (dBm) |
|---|---|
| WLAN 2.4GHz | 19.51 |
| WLAN 5GHz | 21.15 |
This device is restricted to indoor use where operated in the European Community using frequency in 5150MHz-5350MHz to reduce the potential for interference.
|
AT| BE| BG| CH| CY| CZ| DE| DK
---|---|---|---|---|---|---|---|---
EE| EL| ES| Fl| FR| HR| HU| IE
IS| IT| LI| LT| LU| LV| MT| NL
PL| PT| RO| SE| SI| SK| TR| UK(NI)
Manufacturer
Manufacturer: SamKnows Limited
Address: Hill House,1 Little New Street,London, EC4A 3TR,United Kingdom
This product can be used across EU member states.
EU Regulatory Conformance
Hereby, SamKnows Limited Corporation declares that this device is in
compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EU.
For the declaration of conformity, visit the Web site https://samknows.com
/eu-certification
Federal Communication Commission (FCC) Radiation Exposure Statement
When using the product, maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
RF exposure information: To maintain compliance with FCC RF exposure
requirements, use the product that maintain a 20cm separation distance between
the user’s body and the host. MPE limit for RF exposure at prediction
frequency is 1.0mW/cm2 for 2.4G&5G WiFi. The Max MPE for 5G WiFi is
0.112mW/cm2. It satisfy RF exposure compliance-
NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications or changes to this
equipment. Such modifications or changes could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- C-onsult the dealer or an experienced radio/TV technician for help.
The device for operation in the band 5150-5350MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite
systems.
FCC ID:2AGPP-SKWB8V3
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>