CORSAIR 20LAG9901 Light Strip Pro User Manual

CORSAIR 20LAG9901 Light Strip Pro

Placement

• The length of the Light Strip Pro can be adjusted are adapted to the manner where you want to use it maximum strip length is 2000 mm). To the Light
• To shorten Strip Pro, use scissors around the strip at the opale copper cutting cushions. A couple Before you do this, feed Light Strip Pro weld.
• Prepare the surface for installation clean with a lint-free cloth. Pull a piece of the protective film on the adhesive strip weld and attach the Light Strip Pro on the surface by 5 to 10 seconds. Now draw the remaining protective film a little little read with one hand while you use the other hand to remove the adhesive strip to press. After you use Light Strip Pro and have fully confirmed, you go with your fingertips consider the entire length of it to make sure he sticks well. Use the extra Tesa® adhesive strips to stick the controller in place.
• The Light Strip Pro and the controller are magnetic so you can use it without glue on magnetic metal surfaces. If you have an ICD or
• If you have a pacemaker, avoid close prolonged contact with magnets or their magnetic fields.

Installation

• Download and install the Control Center app for Mac, Windows, iOS or Android: elgato.com/download
• Connect the LED strip to the controller Then connect the controller to the power supply and plug it in the Wall outlet. After booting, Light Strip Pro will see a quick start-up procedure and pairing mode starts.
• Open the Control Center app and click on the t symbol around the Light Strip Pro to connect. Control Center helps you now with the configuration. If you have a Mac used for linking via WiFi, switch on the Light Strip Pro, click on the WiFi symbol at the top right, and select your new accessory.
• Complete the configuration with Airport Configuration Utility, the Light Strip Pro can be accessed from the Elgato Control Center.
• Use the Control Center to activate the Light Strip
• Turn Pro on or off, turn the brightness on to fit, choose the exact color, and set the color temperature. Power your PC doesn’t have WiFi, then use you have the Elgato Control Center app on your iOS or Android device to use the Light
• Add Strip Pro. For the initial pairing requires a WiFi connection.
• After the connection, you can use the Light Strip Pro Control via any wired or wireless device in your network.

Reset

RESET restores factory settings from the Light Strip Pro and removes all wifi login details. Hold the RESET button pressed for at least 10 seconds with a small pointed object until the light Flashes 3 times. The Light Strip Pro starts automatically restarts and activates the pairing mode again.

Warning

• The Light Strip Pro can be used during prolonged use will be hot. Always be careful.
• The Light Strip Pro is exclusive for indoor use.
• Cover this product. and especially the controller, not finished.
• Be especially careful when there are children in it are nearby.
• Do not expose the Light Strip Pro to direct sunlight.
• Keep the illuminated surface clear of dust and dirt. Wipe a become dirty Light Strip Pro: carefully with a soft, damp cloth with some water and a mild, neutral detergent. Benzene, thinner and other volatiles substances can cause irreparable damage cause and should not occur used to clean the product to make.
• Do not use the product for anything other than in this manual or on the packaging mentioned applications.
• Only use accessories that come with it product are supplied or supplied by the manufacturer are indicated as compatible.
• RESET will restore Light Strip Pro factory settings and forget all Wi-Fi credentials.
• Push and hold the RESET Button with a small tool for at least 10 seconds until the light flashes 3x.
• Light Strip Pro will reboot automatically and re-engage pairing mode.

Wi-Fi 2. 4 GHz Max RF e.i.r.p power< 20 dBm, Wi-Fi 5 GHz Max RF e.i.r.p. power< 23 dBm, Temperature range: 0 °C – 45 °c

FCC

This equipment complies with FCC RF, IC RSS-102 and CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For indoor use only.
Hereby, Corsair Memory Inc. declares that this device complies with the essential requirements and other relevant provisions of Directive 2014/ 53/EC. The declaration of conformity for Elgato products is available at www.elgato.com/doc

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>