nVent CADDY IGBSF Nail Gun Insert Owner’s Manual

nVent CADDY IGBSF Nail Gun Insert

Product Information

Specifications

• Material: Nylon
• Diameter: 3/4 A: 0.240
• Height: 0.330
• Hole Size: 0.120

Additional Product Details

For additional product details, please refer to the instruction sheets available at www.nvent.com or contact your nVent customer service representative.

Contact Information

If you have any questions or need assistance, you can contact nVent customer service representatives in the following regions:

• Europe Netherlands: +31 800-0200135
• France: +33 800 901 793
• Germany: 800 1890272
• Other Countries: +31 13 5835404
• APAC Shanghai: +86 21 2412 1618/19
• Sydney: +61 2 9751 8500

Disclaimer

Please note that nVent reserves the right to change specifications without notice. It is important to follow the provided instruction sheets and training materials for proper installation and usage of nVent products. Failure to do so may result in product malfunction, property damage, serious bodily injury, and voiding of warranty.

Product Usage Instructions

Step 1: Preparation

Before using the Nail Gun Insert, ensure that you have the following:

• Nail gun (gas or battery-actuated)
• Pole (if planning to install from the floor)
• Junction boxes, electrical boxes, or cable trunking to be fastened
• nVent CADDY Metal Pressure Clip (compatible with the Nail Gun Insert)

Step 2: Attaching the Nail Gun Insert

To attach the Nail Gun Insert, follow these steps:

1. Make sure the nail gun is turned off and disconnected from any power source.
2. Locate the nozzle of the nail gun.
3. Align the Nail Gun Insert with the nozzle and firmly clip it onto the nozzle.
4. Ensure that the Nail Gun Insert is securely attached and does not move or wobble.

Step 3: Fastening Junction Boxes, Electrical Boxes, or Cable Trunking

Once the Nail Gun Insert is attached, follow these steps to fasten the desired objects:

1. Position the nail gun with the Nail Gun Insert at the desired location for installation.
2. If using a pole for hands-off installation, ensure that the pole is securely held.
3. Aim the nail gun at the target object (junction box, electrical box, or cable trunking).
4. Press the trigger of the nail gun to release the nail and secure the object in place.
5. Repeat the process for each desired installation location.

Step 4: Removing the Nail Gun Insert

When you have completed your installations, follow these steps to remove the Nail Gun Insert:

1. Turn off and disconnect the nail gun from any power source.
2. Gently unclip the Nail Gun Insert from the nozzle of the nail gun.
3. Store the Nail Gun Insert in a safe place for future use.

FAQ (Frequently Asked Questions)

• Can I use the Nail Gun Insert with any nail gun?
• The Nail Gun Insert is designed to be compatible with gas or battery-actuated nail guns. However, it is recommended to check the compatibility with your specific nail gun model.
• What is the maximum diameter of nails that can be used with the Nail Gun Insert?
• The Nail Gun Insert has a hole size of 0.120, which can accommodate nails with a diameter up to 0.120 inches.
• Is the Nail Gun Insert suitable for fastening materials other than junction boxes, electrical boxes, and cable trunking?
• The Nail Gun Insert is specifically designed for fastening junction boxes, electrical boxes, and cable trunking. It may not be suitable for other materials or applications.
• How can I obtain the instruction sheets for the Nail Gun Insert?
• The instruction sheets for the Nail Gun Insert can be found on the event website at www.nvent.com. Alternatively, you can contact your nVent customer service representative for assistance.
• Can I use the Nail Gun Insert with other nVent products?
• The Nail Gun Insert is compatible with the nVent CADDY Metal Pressure Clip. It is recommended to check compatibility with other nVent products before use.

CATALOG NUMBER

• IGBSF

FEATURES

• Clips onto the nozzle of gas or battery-actuated nail guns allow for hands-off installation at the structure or from the floor using a pole
• Ideal for fastening junction boxes, electrical boxes and cable trunking
• Helps prevent damage when fastening to brittle materials
• Works with nVent CADDY Metal Pressure Clip
• Halogen-free

PRODUCT ATTRIBUTES

• Material: Nylon
• Diameter: 3/4″
• A: 0.240″
• Height: 0.330″
• Hole Size: 0.120″

ADDITIONAL PRODUCT DETAILS
Nail gun insert is compatible with BeA® CN60-688ES, Hilti® BX 3, GX 3, DEWALT® Trak-It C3, SPIT® PULSA 800E, 700, 1000 or equivalent nailers.

DIAGRAMS

WARNING

• nVent products shall be installed and used only as indicated in nVent’s product instruction sheets and training materials.
• Instruction sheets are available at www.nvent.com and from your nVent customer service representative. Improper installation, misuse, misapplication or other failure to completely follow nVent’s instructions and warnings may cause product malfunction, property damage, serious bodily injury and death and/or void your warranty.

CONTACT

North America

• +1.800.753.9221
• Option 1 – Customer Care
• Option 2 – Technical Support

Europe

• Netherlands:
• +31 800-0200135
• France:
• +33 800 901 793

Europe

• Germany:
• 800 1890272
• Other Countries:
• +31 13 5835404

APAC

• Shanghai:
• + 86 21 2412 1618/19
• Sydney:
• +61 2 9751 8500

nVent.com. CADDY ERICO HOFFMAN RAYCHEM SCHROFF TRACER

© 2023 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without notice.

References

• Building a more Sustainable and Electrified World | nVent
• Building a more Sustainable and Electrified World | nVent

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>