imc M60 Mistral Bottle Cooler Instruction Manual

imc M60 Mistral Bottle Cooler

Product Information

• Specifications
  • Date Purchased: _____
  • Model Number: __
  • Serial Number: __
  • Dealer: ____
• Warranty
  • These bottle coolers are guaranteed by Lincat/IMC for 2 years from the date of purchase from Lincat/IMC, or from one of its stockists, dealers or distributors.
  • The guarantee is limited to the replacement of faulty parts or products and excludes any consequential loss or expense incurred by the purchaser.
  • Defects which arise from faulty installation, inadequate maintenance, incorrect use, connection to the wrong electricity supply, or fair wear and tear, are not covered by the guarantee.
  • The guarantee applies in this form to installations within the United Kingdom. Export units carry 2 years parts only warranty.
• Delivery
  • The packaged machine consists of: M60 Bottle Cooler
  • Shelf (Full size) – 1
  • Shelf clips – 8
  • Sets of keys – 2
  • M90 Bottle Cooler
  • Shelf (Full size) – 1
  • Shelf clips – 12
  • Sets of keys – 2
  • M135 Bottle cooler
  • Shelf (Full size) – 1
  • Shelf clips – 16
  • Sets of keys – 3
• Instruction Booklet – 1
  • Please notify both the carrier and the supplier within 24 hours of receipt if anything is missing or damaged.
  • Check that the correct machine has been supplied and that the voltage, marked on the rating plate, is suitable for the supply available.
  • The rating plate is located internally on the right hand side of the unit.
• Introduction
  • The Mistral M60, M90 and M135 are back-bar or under-bar refrigerators designed for the cooling and storage of beverages. The following quantity of beverage bottles/mixers can be held in each unit:

Bottle Cooler| M60 (900h x 600w x 500d) std| M60 (850h x 600w x 500d)| M60 (800h x 600w x 500d)
---|---|---|---
Capacity (330ml Bottles / 150ml mixer cans)| 120| 72 / 48| 72 / 48
Bottle Cooler| M90 (900h x 900w x 500d) std| M90 (850h x 900w x 500d)| M90 (800h x 900w x 500d)
Capacity (330ml Bottles / 150ml mixer cans)| 195| 117 / 78| 117 / 78
Bottle Cooler| M135 (900h x 1350w x 500d) std| M135 (800h x 1350w x 500d)|
Capacity (330ml Bottles / 150ml mixer cans)| 310| 185 / 125|

Mistral Dimensions: Refer to the table in the user manual for detailed dimensions of each model.

Product Installation

• For the Installer
  • These Instructions contain important information designed to help the user obtain the maximum benefit from their investment in a Lincat/IMC Mistral Bottle Cooler.
  • Please read them carefully before starting work, and consult with the supplier in the event of any queries.
  • Be sure to leave this Instruction Manual with the user after installation of the machine is complete.
• Procedure
  • WARNING: The following table shows the weight and the minimum quantity of people required to lift each unit:

FAQS

• Q: What is the warranty period for the Mistral bottle coolers?
• A: The Mistral bottle coolers come with a 2-year warranty from the date of purchase.
• Q: What does the warranty cover?
• A: The warranty covers the replacement of faulty parts or products, excluding any consequential loss or expense incurred by the purchaser. It does not cover defects arising from faulty installation, inadequate maintenance, incorrect use, connection to the wrong electricity supply, or fair wear and tear.
• Q: Can the Mistral bottle coolers be used outside of the United Kingdom?
• A: Export units carry a 2 years parts only warranty and are suitable for installations outside of the United Kingdom.
• Q: How many beverage bottles/mixers can each unit hold?
• A: Please refer to the capacity table in the user manual for the specific quantity of bottles/mixers that each unit can hold.

WARRANTY

• These bottle coolers are guaranteed by Lincat/IMC for 2 years from the date of purchase from Lincat/IMC, or from one of its stockists, dealers or distributors.
• The guarantee is limited to the replacement of faulty parts or products and excludes any consequential loss or expense incurred by the purchaser.
• Defects which arise from faulty installation, inadequate maintenance, incorrect use, connection to the wrong electricity supply, or fair wear and tear, are not covered by the guarantee.
• The guarantee applies in this form to installations within the United Kingdom.
• Export units carry 2 years “parts only” warranty.
• Please observe these instructions carefully.

DELIVERY

• The packaged machine consists of:

M60 Bottle Cooler containing:|
---|---
Shelf (Full size)| 2
Shelf clips| 8
Sets of keys| 2
M90 Bottle Cooler containing:|
Shelf (Full size)| 2
Shelf clips| 12
Sets of keys| 2
M135 Bottle cooler containing:|
Shelf (Full size)| 2
Shelf clips| 16
Sets of keys| 3
Instruction Booklet| 1

• Please notify both the carrier and the supplier within 24 hours of receipt if anything is missing or damaged.
• Check that the correct machine has been supplied and that the voltage, marked on the rating plate, is suitable for the supply available.
• The rating plate is located internally on the right hand side of the unit.

INTRODUCTION

The Mistral M60, M90 and M135 are back-bar or under-bar refrigerators designed for the cooling and storage of beverages. The following quantity of beverage bottles/mixers can be held in each unit:

Mistral Dimensions

INSTALLATION

For the Installer

• These Instructions contain important information designed to help the user obtain the maximum benefit from their investment in a Lincat/IMC Mistral Bottle Cooler.
• Please read them carefully before starting work, and consult with the supplier in the event of any queries.
• Be sure to leave this Instruction Manual with the user after installation of the machine is complete.

Procedure

WARNING: The following table shows the weight and the minimum quantity ofpeople required to lift each unit:

• Install the unit on a flat and level floor.
• Ensure a minimum 10mm clearance either side of the unit, there is to be a minimum 20mm clearance at the top of the unit and a minimum 60mm clearance at the back.
• The M135 is supplied on castors to aid installation and cleaning.
• Do not install the unit close to a heat source such as a radiator or a warm air outlet. Ensure that the unit is standing level by adjusting the feet on the base of the unit.
• The unit has an automatic defrost cycle and evaporates all the condensate water without the need for a drainage system.

NOTE!

• The castors on the M135 are to aid installation only. The machine is not designed to be used as a mobile unit.
• It is important to install the Bottle Cooler on a flat surface. This ensures that the doors are level. Adjustment is provided via the feet, to enable the installer to level the cabinet.
• Engineer Call-outs in order to level Bottle Coolers, will not be covered under warranty.

TURNING LED LIGHTS ON-OFF

• The cabinet is illuminated by a LED light unit, this light can be turned on or offby depressing the switch that is located on the underside of the worktop.
• To access this switch the door must be opened (the right hand furthest door on the M90 & M135 units).
• When the switch is flush the lights are on.

CHANGING A LED LIGHT ASSEMBLY

The cabinet interior is illuminated by a LED light strip fitting located at the front of the top inner panel.
To change the light assembly:

• Ensure the mains power to the unit has been turned off.
• Open the front cabinet door(s).
• Unscrew the screws holding the LED assembly in place.
• Carefully lower the LED assembly down and disconnect the 2 wires from the unit.
• The LED light assembly should now be free to fully remove from the unit.
• To fit the replacement unit.
• Place the new LED light assembly inside the unit, re connect the 2 wires from the unit to the new LED light assembly.
• Re fit the LED light assembly inside the unit by using the screws.
• Re-connect the mains power and ensure the light illuminates by means of the switch.

ELECTRICITY SUPPLY CONNECTION

Position the unit in the chosen site. The electricity supply connection should be made to a power outlet socket or isolator mounted on the wall close to the machine. This socket or isolator must be accessible once the machine is installed. Before connecting, check that the voltage shown on the rating label is correct for the electricity supply you have available. If the plug does not fit your sockets or a longer lead is required, changes must be made by an approved electrician.
NOTE: The plug is fitted with a 10amp fuse. The plug fuse cover must be refitted when changing the fuse. In the event of losing the fuse cover the plug must NOT be used until a replacement fuse cover has been obtained and fitted or the plug replaced.
WARNING: This machine must be earthed Should the supply cord become damaged then a replacement must be fitted by an approved electrician. The IET Codes of Practice must be observed.
The wires in the mains lead are coloured in accordance with the following code:

• Green and yellow Earth
• Blue Neutral
• Brown Live

COMMISSIONING

• Before using a bottle cooler for the first time, the interior should be wiped out with a clean damp cloth.
• Allow the machine to stand for 1 hour to allow the refrigerant to settle.
• Plug in and switch on at the wall socket. There is no separate switch to turn on the machine.
• The compressor will start running less than one minute after the supply is switched on.
• Check that the light is working, and check the switch is operating correctly.
• Run the unit empty, and check that cold air is being circulated within the cabinet.

CHANGING THE CONTROLLER SET POINT
The electronic temperature controller is factory set to 4°C and will cycle the air temperature between 2°C and 6°C. The set point can be adjusted between 0°C and 18°C by following the button sequence below:

USING YOUR BOTTLE COOLER

• This unit is for cooling bottles and cans only. Do not load the cabinet with boxed goods as this prevents air circulation and the goods will not cool down as quickly.
• While loading ensure that the interior grilles are not obstructed by the bottles.
• Do not place hot or warm goods in the cabinet. Only goods at room temperature or less should be placed in the unit, otherwise performance will be affected.
• It is recommended that the cabinet is stocked after closing at night or first thing in the morning to allow time for the bottles to cool.
• Ensure that stock is rotated by placing new stock at the back of shelves or in one side of the cabinet to ensure that colder bottles are served first.
• Do not leave the doors open when the unit is running as this causes the evaporator to ice up, preventing the unit from operating efficiently.
• Ensure that the front grille is always unobstructed.

CLEANING

• Clean doors and surfaces as required, occasionally remove all merchandise and clean interior surfaces with a clean damp cloth.
• DO NOT USE CLEANING MATERIALS CONTAINING ABRASIVES OR BLEACHES.
• In the case of heavy soiling use a mild liquid detergent. The unit can be washed on the inside using bicarbonate of soda to remove stale smells.

CHANGING SHELF POSITION

• The shelves in all Mistral units are fully adjustable. To adjust the shelves:
• Remove the shelf.
• Unclip the shelf supports as shown below.
• Hook the shelf supports in the required location.
• Ensure all shelf supports are at the same height for a level shelf. The support strips are numbered to aid positioning.
• Replace the shelf.
• On the shelves in the M135 ensure that the clips are in position on the front covering the join (it should be a tight fit if not squeeze the clip slightly to give a better fit).
• Extra shelves are available from Lincat/IMC.

MAINTENANCE

Warning

• Never service, repair or troubleshoot a unit unless you are a professional air conditioning / refrigeration service person.
• Improper servicing can lead to serious injury or death from fire, electric shock or explosion.
• Remove the service panel and insulation block inside the cabinet after switching the unit off from the mains supply.
• Clean the compressor coil with a brush and vacuum cleaner.
• THIS MUST BE DONE every three months or when dirty (whichever is sooner).
• Re-fit the insulation and service panel and secure with the original screws.
• Once the service panel has been re-fitted clean the grille at the bottom front of the cabinet.
• Reconnect the power supply and check that unit returns to normal operation.
• Other than regular cleaning the unit requires no maintenance by the end user.
• It is recommended that the unit is serviced by a Lincat/IMC approved engineer at least once a year.
• Details of IMC Service Contracts are available on application.

DO’S AND DON’TS

• Do Install on a level surface.
• Do Ensure plug is accessible with the unit installed.
• Do Regularly clean the condenser and compressor.
• Do Rotate stock of bottles.
• Don’t Sit or stand on the unit worktop.
• Don’t Load with boxed goods.
• Don’t Leave the doors open.
• Don’t Cover the shelves with any protective materials which may obstruct air circulation through them.
• Don’t Install unit in direct sunlight.
• Don’t Block the air inlet grilles.
• Don’t Store food in the unit.
• Don’t Place hot or warm goods in the unit.
• Don’t Use the unit outside.
• Don’t Use mechanical devices to accelerate the defrosting process.
• Don’t Use electrical appliances inside the storage area, unless they are recommended by the manufacturer.
• Don’t Store explosive substances such as aerosol cans with flammable propellant in the appliance.

END OF LIFE DISPOSAL

At the end of its useful life the unit must be disposed of correctly and safely, to meet the requirements of EU legislation regarding the recovery of ozone depleting substances. The unit must be sent to a specialist recovery, recycling and disposal site that is licensed for the disposal of refrigerated equipment. Please note that the insulation in the Mistral range does not contain any ozone depleting substances. The refrigerant used in the Mistral M60, M90 and M135 is R290a.

Warning
The refrigerant used in this Bottle Cooler is R290a and is Flammable

MATERIAL CONTENT
The Mistral units may contain a combination of the following materials;

• Metals Stainless Steel, Mild Steel (Inc. Nickel Plated, Chrome Plated & Zinc Plated), Aluminium and Copper.
• Plastics & Rubber PVC, Nylon, Polypropylene, Polycarbonate, Polyester, Acetate, Neoprene Rubber and Silicone Rubber.
• Insulation Polystyrene, Polyurethane Foam.
• Oils & Gases Ester oil, Refrigerant R290a.
• Other Glass, Magnesium Oxide, electronic components.

WIRING DIAGRAM

M60 WIRING DIAGRAM

M90 WIRING DIAGRAM

M135 WIRING DIAGRAM

SPARES IDENTIFICATION FRONT

SPARES IDENTIFICATION REAR

SPARE PARTS LIST

Mistral M60 – Series 13

• Part No Description
  • A11/278 Door Gasket
  • A11/283 Door Gasket (850)
  • A11/284 Door Gasket (800)
  • A12/073 Pilaster Strip
  • A12/091 Z1 Shelf
  • A12/082 Wine Shelf
  • S76/025 Perforated Shelf 60
  • A12/036 Shelf Clip (4 per shelf)
  • A19/027 Glider Foot
  • A21/011 Lock, clip & keys
  • E76/221 Access panel
  • G30/561 Electronic Controller (Red)
  • G42/020 Plastic Drip Tray
  • G40/101 M6 Mains Cable
  • G60/349 Mains cable EU plug
  • S76/300 Refrigeration Pack
  • S76/306 Refrigeration Pack 220V-60Hz
  • J09/054 Condenser/fan motor assembly
  • J09/026 Evaporator
  • J09/007 Service Drier
  • X08/057 (2mtr) Capillary 60
  • G96/049 Evaporator Fan
  • C46/001 Z Door Handle (State Colour)
  • S76/250 LED assembly (white)
  • S76/253 LED assembly (red)
  • S76/256 LED assembly (blue)
  • S76/259 LED assembly (green)
  • A11/279 Door Gasket
  • A11/285 Door Gasket (850)
  • A11/286 Door Gasket (800)
  • A12/073 Pilaster Strip
  • A12/092 Z1 Shelf
  • A12/051 Wine Shelf
  • S76/024 Perforated Shelf 90
  • A12/036 Shelf Clip (6 per shelf)
  • A19/027 Glider Foot
  • A21/011 Lock, clip & keys
  • E76/221 Access panel
  • G30/561 Electronic Controller (Red)
  • G42/020 Plastic Drip Tray
  • G40/101 M6 Mains Cable
  • G60/349 Mains cable EU plug
  • S76/301 Refrigeration Pack
  • S76/307 Refrigeration Pack 220V-60Hz
  • J09/046 Condenser/fan motor assembly
  • G40/239 Condenser Fan – Motor Only
  • J09/045 Evaporator
  • J09/007 Service Drier
  • X08/057 (3mtr) Capillary 90
  • G96/049 Evaporator Fan
  • C46/001 Z Door Handle (State Colour)
  • S76/251 LED assembly (white)
  • S76/254 LED assembly (red)
  • S76/257 LED assembly (blue)
  • S76/260 LED assembly (green)

Mistral M135 – Series 13

• Part No Description
  • A11/279 Door Gasket
  • A11/286 Door Gasket (800)
  • A12/073 Pilaster Strip
  • A12/099 Shelf
  • A12/102 Wine Shelf
  • E76/267 Perforated Shelf LH 135
  • E76/268 Perforated Shelf RH 135
  • A12/036 Shelf Clip (6 per shelf)
  • A19/027 Glider Foot
  • A21/011 Lock, clip & keys
  • E76/221 Access panel
  • G30/561 Electronic Controller (Red)
  • E77/123 Drip Tray 135
  • G40/101 M6 Mains Cable
  • G60/349 Mains cable EU plug
  • S76/302 Refrigeration Pack
  • S76/308 Refrigeration Pack 220V-60Hz
  • J09/046 Condenser/fan motor assembly
  • G40/239 Condenser Fan – Motor Only
  • J09/042 Evaporator
  • J09/007 Service Drier
  • X08/057 (2mtr) Capillary V135
  • G96/049 Evaporator Fan
  • C46/001 Z Door Handle (State Colour)
  • S76/252 LED assembly (white)
  • S76/255 LED assembly (red)
  • S76/258 LED assembly (blue)
  • S76/261 LED assembly (green)

ORDERING SPARE PARTS

• In the event that spare parts or accessories need to be ordered, please always quote the SERIES AND SERIAL NUMBER of the machine. This is to be found on the rating plate located near the supply cable.
• For installations outside the UK please contact your supplier.
• For information on IMC spares and service support (if applicable), please call Lincat on +44 (0) 1522 875520. Alternatively, contact us via email:
  • Lincat Spares Desk E-mail: spares@Lincat.co.uk.
  • Lincat Service Desk E-mail: service@Lincat.co.uk.
• Lincat Limited
  • Whisby Road,
  • Lincoln, LN6 3QZ,
  • United Kingdom
  • Tel: +44 (0)1522 875500
  • E-mail: info@Lincat.co.uk.
  • Website: www.Lincat.co.uk.
• FURTHER INFORMATION
  • https://lincat.co.uk/brands/imc.
  • https://www.youtube.com/watch?v=1hSfEPKi-fg.

Please make a note of your product details for future use:

• Date Purchased: _____
• Model Number: __
• Serial Number: __
• Dealer: ____

Documents / Resources

| imc M60 Mistral Bottle Cooler [pdf] Instruction Manual
M60, M90, M60 Mistral Bottle Cooler, Mistral Bottle Cooler, Bottle Cooler, Cooler, M135
---|---

References

• Home - Lincat Catering Equipment
• IMC Archives - Lincat Catering Equipment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>