IMC TOYS 911284-VCC Newborn Coney Instruction Manual
- October 30, 2023
- IMC TOYS
Table of Contents
911284-VCC Newborn Coney
Instruction Manual
WARNING: This product contains a Button or Coin Cell Battery. A swallowed Button or Coin Cell Battery can cause internal chemical burns in as little as two hours and lead to death. Dispose of used batteries immediately. Keep new and used batteries away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
FCC statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interferenceand (2) this device must accept any interference received,
including interference that may cause undesired operation. Warning: Changes or
modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operatethe equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limitsare designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one ormore of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Batteries warnings
- Do not mix old and new batteries.
- Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries. Canada ICES-003 Compliance label: CAN ICES-3(B) / NMB-3(B)
INSTRUCTIONS FOR USE
PRODUCT CHARACTERISTICS
Play with Coney and take care of her! The doll makes sounds and demands your
attention, just like a baby! Only you can calm her down with the bracelet.
Remove the pacifier and she will cry real tears.
USE AND OPERATING INSTRUCTIONS
IMC TOYS products undergo strict production controls to guarantee the
enjoyment and safety of your children. They are easy to use and operate. We
are certain that they will provide your children with great entertainment.
Thank you for purchasing one of our products.
To consult our extensive product catalogue, please visit our web page at
www.imctoys.com
IMPORTANT INFORMATION
NOTE FOR ADULTS
Before giving the product to children, first remove all plastic, wires and any
other object designed to fasten it during transport. This product comes
factory-prepared for the “TRY ME” function. The batteries that it includes are
designed for this use. Therefore, it is possible that they may be spent. If
this is the case, we recommend they should be replaced. The product is shipped
from the factory for demonstration in shops with the selector in the TRY-ME
position. In this position, the product has limited functionality. Position
the selector (A) in the ON position for normal operation (see fig. 1).
BATTERY OPERATION
Doll – Replacement and insertion
Warning! Remember to empty the water from the tank inside the doll before
replacing the batteries, to prevent the water from spilling (see the “Purging
and emptying the tank” section of this manual). This product requires 2 (AAA)
1.5 V alkaline batteries. First of all open the Velcro fastener on the doll’s
back and turn the selector switch (A) to the OFF position (see fig. 1). Remove
the safety screws from the battery compartment lid (B) located on the back
(see fig. 2). Take out the exhausted batteries. The correct insertion of the
batteries is shown in the illustration (see fig. 2). Place them in the
indicated position with the required polarity. Screw the lid on again, to
ensure the safety of your children. Lastly, set the selector switch (A) to ON
and close the Velcro fastener.
Bracelet – Replacement and insertion
This product requires 1 x 3V CR2032 battery. Remove the safety screw from
the battery compartment lid (C) located on the back (see fig. 2). Take out the
exhausted battery. The correct insertion of the battery is shown in the
illustration (see fig. 2). Place it in the indicated position with the
required polarity. Screw the lid on again, to ensure the safety of your
children. Warning! The batteries must always be replaced or handled under the
supervision of an adult. Read the warnings and safety section.
BEFORE STARTING
Filling the tank:
Note: Perform this operation away from elements that can be damaged by water
(electronic devices, plugs, etc.). First of all, for filling the tank, open
the lid (D) located on the back of the head (see fig. 3.) Using a container or
a glass, pour water into the tank. After filling the water tank, close the lid
(D).
PURGING AND EMPTYING THE TANK
Important! Before performing this operation, choose an appropriate place where
no damage to materials or products will be caused by spilled water (for
example, in the bathroom washbasin or the kitchen sink).
PURGING:
When using the product for the first time and/or after filling, water might
not appear in the doll’s eyes when the pacifier is taken away. This may simply
be due to air that is stopping the water from coming out. To purge that air,
use the purge or emptying function. Turn the selector switch (A) to OFF and
remove the pacifier. Then, turn the selector switch (A) to the TRY-ME position
and bring the bracelet close to the doll while you press the button (F) on it.
When the purge function is activated, the lights in her cheeks will go on and
you will hear a double “beep” confirming it has been activated. Wait until
water appears in both eyes (see fig. 4). If you release the button (F) during
the purging process and/or move the bracelet away from the doll, the purging
will stop and it will be necessary to carry out the aforementioned process
again. Caution! Remember, the water will emerge with some pressure in the
form of a jet. As soon as the water appears, stop pressing and the water will
fall in the form of droplets again. To stop the water from dripping, put the
pacifier back in the doll’s mouth.
EMPTYING:
Remove the lid (D) and turn the doll upside down to empty all the water
inside. To empty all the water as recommended in the maintenance section,
perform the operation indicated above, but in this case, keep the button (F)
pressed until there is no water in the
eyes.
OPERATION
With the selector switch (A) set to ON, remove the pacifier (E) from the
doll’s mouth and she will start to cry (sounds and tears). To stop the tears
from falling, put the pacifier (E) back in the doll’s mouth (see fig. 5).
There must be water inside the doll for the crying function to work.
When the doll is laid down, she will automatically close her eyes. If you put
her upright again, she will open her eyes (see fig. 6).
INTERACTION WITH THE BRACELET:
First of all, the user has to put the bracelet (F) on and press the button to activate it (see fig. 7). When both the bracelet and the doll are activated, bring the bracelet close to the doll and her cheeks will light up following a sequence of sounds. If the bracelet is moved away from the doll, she will no longer detect it and her cheeks will be deactivated (see fig. 7.1). If her cheeks do not light up, remove the pacifier or put it back to reactivate the doll and the bracelet. Note: The doll will remain activated for the bracelet to work for about 3 minutes after the last interaction. Once that time has passed, the doll must be reactivated by replacing the pacifier (E) in her mouth or removing it. Remember to press the button (F) on the bracelet again.
NOTE FOR ADULTS!
Although the product contains only a small quantity of water, bear this in
mind when playing, to prevent damage to electrical or electronic appliances
and other products or materials that could be damaged by contact with water.
Do not place these objects near the play area. Remember to put the pacifier
(E) back in the doll’s mouth to stop the tears.
Energy-saving mode
The doll is fitted with 2 types of energy-saving systems to avoid unnecessary
power consumption: She will make sounds without stopping for about 30 seconds
if there is no interaction and change to the partial energy-saving mode for 3
minutes, during which time the doll will react by interacting with the
bracelet. After 3 minutes with no interaction, the doll will change to the
total energy-saving mode. To reactivate the doll, place the pacifier in her
mouth or remove it. To stop it correctly, place the pacifier in the doll’s
mouth and turn the selector switch (A) to OFF.
Tips to ensure correct use
Trouble-shooting:
If the light and sound level is lower than normal, this means the batteries
have run down and they must be replaced (bracelet and doll). If no water
droplets appear in the eyes, first check that the tank still has water and if
not, refill it. If the problem persists, perform the air emptying function
described in this manual (“Purging and emptying the tank” section). If there
is a blockage, do not try to insert sharp objects in the water circuit, as
this could cause damage. Empty the water tank completely, fill it again and
perform the purging process.
MAINTENANCE
Cleaning:
Only the surface of the doll and the bracelet are washable. To wash them, use
a cloth dipped in a mild dry cleaning product. Do not use detergents or
solvents. If the event of wetting the equipment, turn it off and remove the
batteries immediately. Dry the battery compartment with a dry cloth. Leave the
battery compartment open until it is completely dry. This operation can be
speeded up by using a hairdryer. Do not try to use the equipment until it is
completely dry. Note for Adults: For safety and design reasons, the pajamas
cannot be taken off the doll.
Conservation: To avoid damage to the product or accidental water
spillage, you are recommended to remove all the water from the product after
play. To do this, follow the emptying process indicated in the “PURGING OR
EMPTYING” section included in this manual. If the product is not going to be
used for a prolonged period after being emptied, to facilitate evaporation of
the water remaining inside it, we recommend not putting the dummy into the
doll’s mouth and removing the batteries.
RECOMMENDATIONS FOR RESPONSIBLE USE AND FOR PROTECTING THE ENVIRONMENT
Put all the transport packaging, cardboard, plastic, etch, in the recycling
containers in your neighborhood.
If you no longer want the toy and it still works, do not throw it away.
Remember that other people can still enjoy it, and find bodies or associations
that can give it to them.
You must not throw the product away in a rubbish bin when it is no longer any
use.
Use your community recycling services. Products labelled with the WEEE symbol
(a crossed-out rubbish bin) indicate that the end user must not throw the
product away and that it must be taken to a recycling point for electrical and
electronic devices.
Use rechargeable batteries whenever possible. Remember to turn off the toy if
you have finished playing with it and take out the batteries if you are not
going to be using it again for a longtime.
Consult the symbol on the product, in the user manual or on the packaging for
more information. The materials are recyclable in accordance with their
markings. If you recycle materials or find ways to reuse old devices, you make
a considerable contribution to protecting the environment. Please consult the
nearest recycling centre or local authorities.
WARNINGS!
– Warning. This product contains a coin battery. A coin battery can cause
serious internal chemical burns if swallowed.
– Warning. Dispose of used batteries immediately. Keep new and used batteries
away from children. If you think batteries might have been swallowed or placed
inside any part of the body, seek immediate medical attention.
– Warning. This toy produces flashes that may trigger epilepsy in sensitised
individuals.
– Please keep the packaging for future reference as it contains very important
information.
– Please note that due to technical improvements this product may differ from
the one that appears in the illustration.
– This product requires 2 type AAA/1,5V batteries (doll) and 1 type CR2032
(bracelet) (included).
– This product is distributed with 2 type AAA/1,5V and 1 type CR2032 batteries
for the “try-me” function. For normal operation of the product, it may be
necessary to replace the batteries.
– The batteries or accumulators must be inserted according to the polarity
indicated in the illustration.
– Used batteries or accumulators must be removed from the toy; failure to do
so could cause damage.
– Do not mix old batteries with new ones. – Do not mix different types of
batteries.
– Use only those batteries recommended by the manufacturer or equivalents.
– Non-rechargeable batteries must not be recharged.
– The battery terminals must not be bridged or shorted.
– Changing or handling the batteries must always be carried out under the
supervision of an adult.
– Remove the batteries from the compartment if the unit is not going to be
used for a long period of time.
– Please respect the environment and deposit used batteries in the containers
provided.
– Rechargeable batteries are to be removed from the toy before being charged.
– Rechargeable batteries are only to be charged under adult supervision.
– This product achieves better performance using alkaline batteries.
– Read the instructions before use, follow them and keep them for reference.
– Under the environment with radio frequency interference, the sample may
malfunction and will be resumed to normal after removal of the interference.
– Under the environment with electrostatic discharge, the sample may
malfunction and require user to reset the sample.
– Under the environment with Fast Transient, the sample may malfunction and
require user to reset the sample.
– Remove all elements designed to fasten and protect the product during
transport before giving it to children (plastic pieces, labels, wires, etc.).
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, IMC.TOYS S.A. declares that the radio equipment type REMOTE RADIO
CONTROL Receiver category 3, Temperature Category I is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address: https://imctoys.com/es/doc
SIMPLIFIED UK DECLARATION OF CONFORMITY
Hereby, IMC.TOYS S.A., declares that the radio equipment type REMOTE RADIO
CONTROL Receiver category 3, Temperature Category I is in compliance with
Radio Equipment Regulations 2017. The declaration of conformity may be
consulted at https://imctoys.com/es/doc
a) frequency band(s) in which the radio equipment operates: 2418-2462MHz
b) maximum radio-frequency power transmitted in the frequency band(s) in which
the radio equipment operates: < 10 dBm.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
WARNING: Button/coin batteries are hazardous and must be kept out of
reach of children at all times, whether the battery is new or used. These
batteries can cause severe or fatal injuries in 2 hours or less if swallowed
or placed inside any part of the body. Seek medical attention immediately if
it suspected that the battery has been swallowed or placed inside any part of
the body or contact the Australian Poisons Information Centre on 13 11 26 for
24/7 fast, expert advice.
Dispose of used batteries immediately, and out of the reach of children.
- All instruction sheets must be retained since it contains important information.
Points de collected sur www.quefairedemesdechets.fr Battery requirements: Made in China
Manufactured for
IMC. TOYS, S.A. • Pare Labrador, 172 • 08224 Terrassa (Barcelona) SPAIN • NIF:
ES A08667370 • www.imctoys.com
Distributed by IMC US
IMC TOYS USA INC • 14 Fairmount Ave, Suite 4, Chatham NJ 07928 • Phone: (877)
836-0384
Customer Service • Servizio al Consummator • Service Clients:
info.usa@imctoys.com /
help.usa@imctoys.com
IN UK, IMPORTED BY
Unit 1, Somerville Court • Trinity Way • Atterbury • Bunbury • OX17 3SN •
United Kingdom
References
- IMC Toys | A world of toys to have fun and enjoy
- FICHAS COMPOSICIÓN EMBALAJE PRODUCTO | IMC toys
- Que Faire de mes Déchets ? Découvrez les solutions pour tous vos déchets et nos conseils pour en produire moins.
- Declaración de Conformidad | IMC toys
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>