SONOFF MINIR4M Wi-Fi Smart Switch User Manual

SONOFF MINIR4M Wi-Fi Smart Switch

Introduction

MINI Extreme is an extremely compact Wi-Fi smart switch that can be installed in the mounting box, transforming your regular switch into a smart switch. It supports Matter protocol, enabling seamless work with other smart devices from different brands to create a customized home automation system.

1. Button

   • Press once: Changing the on/off state of relay contacts
   • Press and hold for 5 seconds: The device enters the pairing mode.

2. Wi-Fi LED indicator (Blue)

   • eWeLink Mode

   • Keeps on: The device is online.

   • Flashes twice: LAN

   • Flashes once: Offline

   • Flashes two short and one long: The device is in pairing mode.

   • Flashes three times: Trigger mode switched successfully
     Matter Mode

   • Keeps on: The device is online.

   • Flashes once: Offline

   • Flashes two short and one long: The device is in pairing mode.

   • Flashes three times: Trigger mode switched successfully; Identify

3. Wiring ports

Matter-compatible ecosystem

Specification

Installation

Power off

Please install and maintain the device by a professional electrician. To avoid electric shock hazards, do not operate any connection or contact the terminal connector while the device is powered on!

Wiring instruction
To ensure the safety of your electrical installation, either a Miniature Circuit Breaker (MCB) or a Residual Current Operated Circuit Breaker (RCBO) with an electrical rating of 10A must be installed before the MINIR4M.

• No matter if S1 and S2 are connected or left idle to the external switch, this device can be controlled by automation or the App.
• It is prohibited to connect S1 and S2 terminals to the neutral or ground wire, to avoid damaging the equipment and causing danger.
• Make sure all wires are connected correctly.

Power on
After powering on, the device will enter the Pairing Mode defaulted during the first use, and the Network indicator flashes in a cycle of two short and one long.

• The device will exit the Pairing Mode if not been paired within 10mins. If you want to enter this mode again, please long press the button for 5s until the Network indicator flashes in a cycle of two short and one long and then release.

Add device

Method 1: Matter Pairing
Open a Matter-compatible App ( e.g. Alexa App, Google Home App, or Apple Home App, etc ) to scan the Matter QR code on the Quick Guide or the device itself to add the device.

Method 2: eWeLink App Pairing

Download the“eWeLink”App

• Please download the “eWeLink” App from the Google Play Store or Apple App Store.

Add device

1. Please follow the wiring instructions to connect the wires (ensure power is disconnected in advance and consult an electrician if needed)
2. Power on the device
3. Enter“Scan QR code”
4. Scan the Matter QR code on the device body or the back page of the Quick Start Guide.
5. Long press the button for 5 seconds
6. Check the Wi-Fi LED indicator flashing status (Two short and one long flashes)
7. Select“Add Device”
8. Search for the device and start connecting.
9. Select the “Wi-Fi” network and enter the password.
10. Device“Added completely”.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISED Notice

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.
This device complies with RSS-247 of Industry Canada.
Operation is subject to the condition that this device does not cause harmful interference.

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

SAR Warning

• Under normal use of conditions, this equipment should keep a separation distance of at least 20cm between the antenna and the body of the user.

WEEE Warning

WEEE Disposal and Recycling Information All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste.
Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as the terms and conditions of such collection points.

EU Declaration of Conformity

Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type MINIR4M complies with Directive 2014/53/EU. The full text of the EU Declaration of conformity is available at the following internet address: https://sonoff.tech/usermanuals.

CONTACT

• Manufacturer: Shenzhen Sonoff Technologies Co., Ltd.
• Address: 3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China
• ZIP code: 518000 Service email: support@itead.cc.
• Website: sonoff.tech Made in China.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>