oEdRo 2019-2023 Hard Trifold Truck Bed Tonneau Cover Instruction Manual

June 16, 2024
OEDRO

oEdRo 2019-2023 Hard Trifold Truck Bed Tonneau Cover

ASSEMBLY INSTRUCTIONS

Part List

CD| Xl| Cover Assembly
0| X6| Clamp Foam Pad
®| Xl| Seal Strip
©| X2| Replacement Hinge
®| X4| Mounting Block (for Toyota/Nissan/Jeep ONLY)
®| Xl| Allen Wrench (for Toyota/Nissan/Jeep ONLY)
(j)| X2| Bulkhead Seal Sticker (for Tacoma ONLY)

Warning

  1. Tonneau cover must be completely secure in the closed position or opened position while driving. DO NOT DRIVE with cover in partially opened position.
  2. Clean the debris before fold the tonneau cover.
  3. Professional installation would be highly recommended.
  4. Period check to ensure all clamps remain secure and tight.
  5. Remove the tonneau cover before tow the truck from rear.
  6. Do not drive without safety clamps.
  7. Check the hinge before fold or unfold during installation. If any damage found, do not use the cover and contact us.

Step 1

  1. Clean the bulkhead and bed rail before installation.
  2. For Tacoma truck stick the seal sticker on the bulkhead bar.
  3. Srick the seal strip onto the bulkhead.

Step 2

  1. Place cover assembly on front truck bed rail against the cab.
  2. Release safety buckles.

Step 3

  1. Fully unfold the cover towards rear.
  2. Ensure the cover aligns on truck bed.

Step 4
Carefully refold the cover without moving position on the truck bed.

Step 5

  1. Pull down the front clamp to vertical position.
  2. Loosen the knob and slide front clamp to bed rail.
  3. Stick the clamp pad to mounting position on bed rail.
  4. Hook the J-shaped clamp under the metal bed rail lip and tighten the knob.

Note
Hand tighten ONLY. DO NOT over tighten .

The clamps may not precisely vertical.

Step 6

  1. Loosen the safety clamp and attach to the bed rail lip on both side.
  2. Hand tighten the knob clockwise. DO NOT use wrench or overtighten.
  3. Adjust the strap to proper length. and pull the the other end of the strap to tight.

Step 7
Carefully unfold the cover and secure the rear clamps.

  1. Pull down the rear clamp to vertical position.
  2. Slide rear clamp to bed rail.
  3. Stick the clamp pad to mounting position on bed rail.
  4. Turn the clamp handle to adjust rear clamp to proper length.
  5. Hook the J-shaped clamp under the metal bed rail lip and push the clamp handle to vertical position.

Note
The clamps may not precisely vertical.

Step 8

  1. Close the tailgate. Installation completed.

Fold up the Cover

  1. Open the tailgate.

  2. Release and fold up the rear clamps.

  3. Fold up the cover towards front.

  4. Secure the safety buckles.

  5. After the tonneau cover installed, periodic check to ensure all clamps and buckles remain secure and tight.

Special Instruction for Trucks with Utility Rail
For trucks with utility rail

  1. Slide mounting block into track rail.
  2. Attach front clamps onto mounting block.
  3. Attach center and rear clamps onto mounting block.
  4. Tighten set screw on mounting block.

Special Instruction for Tacoma Trucks

  1. Remove the bulkhead bar.
  2. Stick the seal on both ends of bar.
  3. Install the buckhead bar back.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals