70915 Gold Bathroom Vanity Light Fixtures

Product Information

Specifications

• Item Number: Gold Vanity Light
• Parts Included:
  • (C) Green ground screw (1)
  • (D) Mounting plate (1)
  • (E) Stud (2)
  • (F) Glass shade (3)
  • (G) Back plate (1)
  • (H) Arm (3)
  • (I) Socket cup (3)
• Accessories Enclosed:
  • (A) Mounting screw (2)
  • (B) Plastic wire connector (3)
  • (J) Iron bar (9)
  • (K) Plastic anchor (2)
  • (L) Wood screw (2)

Product Usage Instructions

Step 1: Preparation

1. Before starting the installation, make sure to turn off the
   power. Go to the main fuse or circuit breaker box in your home and
   place the main power switch in the OFF position. Also, turn off the
   wall switch.

2. Ensure you have the following tools ready:

   • – Screwdriver
   • – Pliers
   • – Electrical tape

Step 2: Assembly

Step A1: Remove Mounting Plate

Unscrew the studs (E) from the back plate (G) and gently remove
the mounting plate (D).

Step A2: Secure Mounting Plate

Secure the mounting plate (D) to the outlet box using the
provided mounting screws (A), plastic anchors (K), and wood screws
(L).

Step A3: Make Wire Connections

Make the wire connections according to the below chart:

• – Connect wires of the fixture to the corresponding wires in
  your electrical box.

• – Connect the ground wire according to the below chart.

Twist the plastic wire connectors until the wires are tightly
joined together. Wrap each connector with approved electrical tape.
Ensure no wire strands are exposed and carefully tuck all wires
into the outlet box.

Step A4: Attach Back Plate

Align the holes in the back plate (G) with the mounting screws
and attach the back plate (G) using the previously removed studs
(E). Hand tighten until snug.

Step A5: Install Bulbs and Glass Shade

Install bulbs (not included) into the socket cup (I). Fix the
glass shade (F) on the socket cup (I) using an iron bar (J).

Step 3: Final Checks and Usage

1. Ensure everything is installed properly.
2. Turn on the power and enjoy your Gold Vanity Light!

FAQ

Q: Can I install this product myself?

A: We suggest installation by a licensed electrician to reduce
the risk of fire, electric shock, or injury to persons.

Q: How do I clean the fixture?

A: To clean, wipe the fixture with a soft cloth. Clean the glass
with a mild soap. Do not use abrasive materials such as scouring
pads or powders, steel wool, or abrasive paper.

Q: How can I order replacement parts?

A: Keep this sheet for future reference. If you need to order
replacement parts, you can do so from the place of purchase. Make
sure to use the exact wording from the illustration when ordering
parts.

Item Number: Gold Vanity Light WARNING (To reduce the risk of fire, electric shock, or injury to persons): 1. We suggest installation by a licensed electrician. 2. Please read the instruction carefully and save it as you may need it at later time. 3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go
to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position. 4. Mounting surface should be clean, dry, flat, strong enough and 1/4″ larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16″ should be corrected as required. 5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture. 6. Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb. 7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp. 8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly. 9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products. IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED): Before doing assembly and installation please prepare the needed tools as below picture
Page: – 1 – / 3

PARTS INCLUDING: (C) Green ground screw (1) (D) Mounting plate (1) (E) Stud (2) (F) Glass shade (3) (G) Back plate (1) (H) Arm (3) (I) Socket cup (3)
ACCESSORIES ENCLOSED: (A) Mounting screw (2) (B) Plastic wire connector (3) (J) Iron bar (9) (K) Plastic anchor (2) (L) Wood screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS: 1. Carefully remove the fixture from the carton and check that all parts and
accessories are included as shown in the above illustration 2. Turn off power
Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position. 3. Make assembly
Page: – 2 – / 3

Step A1: Unscrew the studs(E) from the back plate(G) then gently remove the mounting plate (D).

Step A2: Secure mounting plate (D) to outlet box with mounting screws (A)plastic anchors (K) and wood

screws (L).

Step A3: Make wire connections

Connect wires as below wires connecting shown. TAKE NOTE OF YOUR WIRE

COLOR OF FIXTURE ,NEVER CONNECT WIRE TO GROUND WIRE

Connect ground wire according to below chart

Connect wires according to below chart

Twist plastic wire connector until wires are tightly joined together,wrap each connector with approved electrical tape.Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box .
Step A4: Align the holes in the back plate (G) with the mounting screws, then attach the back plate (G) using the previously removed studs(E). Hand tighten until snug.
Step A5: Install bulbs (Not included. Please do not exceed the maximum capacity recommended on the socket.) Fix the glass shade (F) on the socket cup (I) with an iron bar (J).
4. Check everything installed properly, then you could turn on the light. Enjoy !
CLEANING To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper. ORDERING PARTS Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.

Page: – 3 – / 3

References

• The domain name tape.be is for sale | Dan.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>