BUTURE B 221117 Car Battery Jump Starter 2500A Jump Box User Manual

BUTURE B 221117 Car Battery Jump Starter 2500A Jump Box User Manual

PACKING LIST

• Beta02 Jump Starter

• Charging Cable

• Smart Jumper Clamps

• EVA Protection Case

• User Manual

KNOW YOUR BETA02

Thanks for choosing BUTURE Beta02 jump starter! Please read all instructions carefully before using this product and keep these instructions for easy reference.

press to switch light mode
LED display| Show the storage level of jump starter and activated output ports
Output*2| Quickly charge your phone, tablet, camera, etc
Input| Recharge the jump starter
Red clamp| Connect to positive terminal of car battery
Black clamp| Connect to negative terminal of car battery
Indicator| Indicate the corresponding problems in use

SPECIFICATIONS

Model l: Beta02
Capacity ; 21800mAh 80,88 wh
INput : 5v/2A
Out pu1 t : 5v/2.4a
output 2 : 6v/3v, 9v/2a, 12v/1.5a
Opreatin Temp : -20°C~60°C

OPERATION GUIDE

OPERATION GUIDE
Before use, please note:
• Charger not included. A universal USB charger is fine, such as your phone charger (2A above is suggested).
• When using the product for the first time, please make sure it is fully charged.
• It is recommended to charge up the product every 3 months to prolong its lifespan even if the unit has not been used.

Recharge the Jump Starter
Step 1. Connect the the jump starter to power supply via the USB C charging cable.

Step 2. Disconnect the power after it is fully charged. Tip: Do not charge the jump starter unit immediately after starting engines, but at least 30 minutes later.

Charge Your USB Devices
Step 1. Plug the Charging Cable to electronic devices with USB output.
Step 2. Press the power button to start charging. Disconnect when charging is not required.

LED Flashlight
Press the switch button 3 seconds to start the LED light and short press to switch to SOS, strobe and off in order.

Start Vehicles
Before use, please note:
• This product is only suitable for 12V vehicles
• Before starting your car, please make sure that the remaining of power is not less than 80%. Fully charged is suggested.

Step 1. Insert the clamp plug completely into the product.

Step 2. Connect the RED clamp to the vehicle’s battery positive (+) terminal and connect the BLACK clamp to the vehicle’ s battery negative (-) terminal.

Step 3. Start the vehicle, and interval time between each starting must be OVER 60s. ENGINE START STOP

Step 4. When the vehicle is started, remove jumper cable from jump starter and disconnect red and black clamps from the vehicle battery terminals within 30 seconds.
Tip: If 3 attempts fail, please check if there are problems of the vehicle engine or circuit, meanwhile, check the jump starter. If problem, please contact us at support@ibuture.com.

INDICATOR AND TROUBLESHOOTING
In any of the following situations, the smart clamp will turn protections on:

The icon above runs in
cycles from left to right| Standby status. Jumper cable connected and product voltage will display.
“ ” is on| Detect and display car battery voltage when the jumper cable conncted to car battery only.
..                                                            flashesass”| Timeout protection—No start within 60s after connection. Reconnect and start.
“ ” flashes,with long beep sound| Jumper cable has sticking fault—Contact support@ibuture.com for replacement parts
“ BBB” flashes,with long beep sound| High voltage protection—Charge other devices through the USB port to lower voltage output
“ ” is on, with short beep| Low voltage protection and EC5 port output voltage will display —Recharge the jump starter
f   is on,.. ” flashes,with short beep| Reverse polarity protection—Reverse the clips and ensure the correct connection
,” is on, ” flashes, with short beep| Reverse charge protection —Recharge the product
“ “ is on,”••in” flashes with short beep| Short circuit protection—Don’t connect the clips together or to the same metal
“ ,” is on,ass” flashes, with short beep| Over-heat protection—Remove the clamps to let it cool

IMPORTANT SAFETY WARNING
ATTENTION: Please read the following safety warning before using the product and take safety protection measures to avoid malfunctions caused by accidental operation.

Personal Safety
1. Store in a cool and well-ventilated place out reach of children and pets.
2. Do not place the product in high temperature environment for a long time. The operation temperature of this product is -20~60°C. The storage temperature should not exceed 50°C/122 °F.

Electrical Safety
1. Only start vehicles with the smart jumper cable supplied by the manufacturer. 2. Do not use the product if the clamp or cable is damaged.
3. Do not connect the red and black clamps together when the product is outputting.
4. Do not connect the red and black clamps to the same piece of metal.
5. Do not disassemble or modify this product.
6. Do not use detergent to clean this product.
7. Do not abuse this product and avoid heavy dropping or repeatedly hitting it.
8. Do not operate the product in explosive environments such as flammable liquids, gases or dusts.
9. Do not immerse the product in water.

Battery Safety
1. Do not litter the product and it should be safely recycled.
2. Do not incinerate the product or exposed to high temperatures, as they may explode.
3. Only use replacement parts or accessories provided or recommended by manufacturer.

WARRANTY
Our company provides customers with warranty of 24 months from the date of purchase.
For assistance or warranty cover claim, please contact us:
Email: support@ibuture.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>